Pretraživanje
Prikaz rezultata 31-40 od 74
The performance of pip-cascade controler in hvac system
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2014)
Primitive controllers used in the early version for HVAC systems, like the on-off (Bang-Bang) controller, are inefficient, inaccurate, unstable, and suffer from high-level mechanical wear. On the other hand, other controllers ...
Determining the theoretical reliability function of thermal power system using simple and complex weibull distribution
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2014)
The main subject of this paper is the representation of the probabilistic technique for thermal power system reliability assessment. Exploitation research of the reliability of the fossil fuel power plant system has defined ...
Thermomechanics of soft inelastics bodies with application to asphalt behavior
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2014)
Thermomechanical behavior of hot mix asphalt (HMA) is considered. Its highly irregular microstructure is covered by the hierarchical approach. A brief survey of endochronic thermodynamics precedes constitutive consideration. ...
Influence of friction stir welding parameters on properties of 2024 t3 aluminium alloy joints
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2014)
The aim of this work is to analyse the process of friction stir welding (FSW) of 3 mm thick aluminium plates made of high strength aluminium alloy - 2024 T3, as well as to assess the mechanical properties of the produced ...
Numerical analysis of temperature field during hardfacing process and comparison with experimental results
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2014)
The three-dimensional transient nonlinear thermal analysis of the hard facing process is performed by using the finite element method. The simulations were executed on the open source Salome platform using the open source ...
Two-dimensional numerical analysis of active flow control by steady blowing along foil suction side by different urans turbulence models
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2017)
The effects of active separation control by steady blowing jets were investigated numerically on three different examples: subsonic flow past Aerospatiale A airfoil at 13 degrees angle-of-attack, transonic flow past NACA ...
Measurement of thermal emission during cutting of materials using abrasive water jet
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2017)
This article deals with measurement of the thermal gradient on material during abrasive water jet cutting. The temperature was measured by thermocamera before the technological process started, during the abrasive water ...
Boundary-layer transition detection by thermography and numerical method around bionic train model in wind tunnel test
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2018)
Methods of diagnosing aerodynamic characteristics are constantly developing in order to conduct the precise and energy efficient wind tunnel testing of transport vehicles in the prototype design early stages. This is of a ...
Influence of material velocity on heat generation during linear welding stage of friction stir welding
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2016)
The heat generated during friction stir welding process depends on plastic deformation of the material and friction between the tool and the material. In this work, heat generation is analysed with respect to the material ...
Experimental and numerical thermo - mechanical analysis of friction stir welding of high - strength alluminium alloy
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2014)
This paper presents experimental and numerical analysis of the change of temperature and force in the vertical direction during the friction stir welding of high-strength aluminium alloy 2024 T3. This procedure confirmed ...