TY  - JOUR
AU  - Živković, A.
AU  - Durdević, A.
AU  - Sedmak, Aleksandar
AU  - Tadić, Srđan
AU  - Jovanović, I.
AU  - Durdević, D.
AU  - Zammit, K.
PY  - 2015
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/2145
AB  - The paper presents results of research on the possibility of producing T-joints of aluminium alloys without defect by friction stir welding process. Friction stir welding process is applied in welding T-joints of aluminium alloys 5052-H32 and 5754-H111. These relatively new welding tech-nologies produce high quality welded joints, where strength of the joint can reach the strength of the base material. Visual and macrostructural examination and microhard-ness measuring of the welded T-joints are processed.
PB  - Institut za ispitivanje materijala, Beograd
T2  - Structural Integrity and Life
T1  - Friction stir welding of aluminium alloys - T joints
EP  - 186
IS  - 3
SP  - 181
VL  - 15
UR  - https://hdl.handle.net/21.15107/rcub_machinery_2145
ER  - 

@article{
author = "Živković, A. and Durdević, A. and Sedmak, Aleksandar and Tadić, Srđan and Jovanović, I. and Durdević, D. and Zammit, K.",
year = "2015",
abstract = "The paper presents results of research on the possibility of producing T-joints of aluminium alloys without defect by friction stir welding process. Friction stir welding process is applied in welding T-joints of aluminium alloys 5052-H32 and 5754-H111. These relatively new welding tech-nologies produce high quality welded joints, where strength of the joint can reach the strength of the base material. Visual and macrostructural examination and microhard-ness measuring of the welded T-joints are processed.",
publisher = "Institut za ispitivanje materijala, Beograd",
journal = "Structural Integrity and Life",
title = "Friction stir welding of aluminium alloys - T joints",
pages = "186-181",
number = "3",
volume = "15",
url = "https://hdl.handle.net/21.15107/rcub_machinery_2145"
}

Živković, A., Durdević, A., Sedmak, A., Tadić, S., Jovanović, I., Durdević, D.,& Zammit, K.. (2015). Friction stir welding of aluminium alloys - T joints. in Structural Integrity and Life
Institut za ispitivanje materijala, Beograd., 15(3), 181-186.
https://hdl.handle.net/21.15107/rcub_machinery_2145

Živković A, Durdević A, Sedmak A, Tadić S, Jovanović I, Durdević D, Zammit K. Friction stir welding of aluminium alloys - T joints. in Structural Integrity and Life. 2015;15(3):181-186.
https://hdl.handle.net/21.15107/rcub_machinery_2145 .

Živković, A., Durdević, A., Sedmak, Aleksandar, Tadić, Srđan, Jovanović, I., Durdević, D., Zammit, K., "Friction stir welding of aluminium alloys - T joints" in Structural Integrity and Life, 15, no. 3 (2015):181-186,
https://hdl.handle.net/21.15107/rcub_machinery_2145 .

TY  - CONF
AU  - Antić, A.
AU  - Željković, Milan
AU  - Petrović, Petar
AU  - Živković, A.
AU  - Hodolč, J.
PY  - 2012
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/1602
AB  - Presented in this paper is a comparative analysis of vibrations, measured during machining process and modelled by FEM. Moreover, microscopic structure of chip cross section was analyzed in order to establish the frequency of lamellae generation and its influence on the total level of vibrations of the cutting tool. Based on the results thus obtained, a method was proposed which allows determination of tool wear degree through separation of reliable indicators from the high-frequency spectrum of the measured vibration signals. This investigation showed that the change of chip segmentation frequency significantly influences the output vibration signal within the high-frequency spectrum, and is a function of tool wear degree.
PB  - Croation Union of Mech. Engineers and Naval Architects
C3  - Strojarstvo
T1  - Experimental analysis and FEM modelling of a cutting tool vibrations
EP  - 125
IS  - 2
SP  - 117
VL  - 54
UR  - https://hdl.handle.net/21.15107/rcub_machinery_1602
ER  - 

@conference{
author = "Antić, A. and Željković, Milan and Petrović, Petar and Živković, A. and Hodolč, J.",
year = "2012",
abstract = "Presented in this paper is a comparative analysis of vibrations, measured during machining process and modelled by FEM. Moreover, microscopic structure of chip cross section was analyzed in order to establish the frequency of lamellae generation and its influence on the total level of vibrations of the cutting tool. Based on the results thus obtained, a method was proposed which allows determination of tool wear degree through separation of reliable indicators from the high-frequency spectrum of the measured vibration signals. This investigation showed that the change of chip segmentation frequency significantly influences the output vibration signal within the high-frequency spectrum, and is a function of tool wear degree.",
publisher = "Croation Union of Mech. Engineers and Naval Architects",
journal = "Strojarstvo",
title = "Experimental analysis and FEM modelling of a cutting tool vibrations",
pages = "125-117",
number = "2",
volume = "54",
url = "https://hdl.handle.net/21.15107/rcub_machinery_1602"
}

Antić, A., Željković, M., Petrović, P., Živković, A.,& Hodolč, J.. (2012). Experimental analysis and FEM modelling of a cutting tool vibrations. in Strojarstvo
Croation Union of Mech. Engineers and Naval Architects., 54(2), 117-125.
https://hdl.handle.net/21.15107/rcub_machinery_1602

Antić A, Željković M, Petrović P, Živković A, Hodolč J. Experimental analysis and FEM modelling of a cutting tool vibrations. in Strojarstvo. 2012;54(2):117-125.
https://hdl.handle.net/21.15107/rcub_machinery_1602 .

Antić, A., Željković, Milan, Petrović, Petar, Živković, A., Hodolč, J., "Experimental analysis and FEM modelling of a cutting tool vibrations" in Strojarstvo, 54, no. 2 (2012):117-125,
https://hdl.handle.net/21.15107/rcub_machinery_1602 .