TY  - JOUR
AU  - Mladenović, Goran
AU  - Bojanić, Pavao
AU  - Tanović, Ljubodrag
AU  - Klimenko, Sergey
PY  - 2015
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/2221
AB  - The paper contains an experimental study of microcutting intended to help the optimization of the grinding process of the oxide ceramic CM332 (99.5% Al2O3) grinding. The need for investigating the mechanisms occurring between the abrasive material and the ceramic is imposed by the fact that grinding is the dominant technology used to achieve the required quality of the workpiece surface finish. The microcutting process was performed with a single diamond cone-shaped grain of tip radius of 0.2mm at varying depths of cut. The investigations were carried out to determine the normal and tangential cutting forces, the critical penetration depth and the specific grinding energy as a function of the grain penetration speed and depth. The critical grain penetration depth separating ductile flow from brittle fracture falls within the 4-6 mu m range. The values of the critical penetration depth are also consistent with the results of changes in the cutting forces and the specific grinding energy. The chip formation mechanism is associated with the presence of median/radial and lateral cracks, ductile flow, chipping along the groove, and crushing beneath the diamond grain, all this affecting the quality of the ceramic's machined surface.
PB  - ASME, New York
T2  - Journal of Manufacturing Science and Engineering-Transactions of The Asme
T1  - Experimental Investigation of Microcutting Mechanisms in Oxide Ceramic CM332 Grinding
IS  - 3
VL  - 137
DO  - 10.1115/1.4029564
ER  - 

@article{
author = "Mladenović, Goran and Bojanić, Pavao and Tanović, Ljubodrag and Klimenko, Sergey",
year = "2015",
abstract = "The paper contains an experimental study of microcutting intended to help the optimization of the grinding process of the oxide ceramic CM332 (99.5% Al2O3) grinding. The need for investigating the mechanisms occurring between the abrasive material and the ceramic is imposed by the fact that grinding is the dominant technology used to achieve the required quality of the workpiece surface finish. The microcutting process was performed with a single diamond cone-shaped grain of tip radius of 0.2mm at varying depths of cut. The investigations were carried out to determine the normal and tangential cutting forces, the critical penetration depth and the specific grinding energy as a function of the grain penetration speed and depth. The critical grain penetration depth separating ductile flow from brittle fracture falls within the 4-6 mu m range. The values of the critical penetration depth are also consistent with the results of changes in the cutting forces and the specific grinding energy. The chip formation mechanism is associated with the presence of median/radial and lateral cracks, ductile flow, chipping along the groove, and crushing beneath the diamond grain, all this affecting the quality of the ceramic's machined surface.",
publisher = "ASME, New York",
journal = "Journal of Manufacturing Science and Engineering-Transactions of The Asme",
title = "Experimental Investigation of Microcutting Mechanisms in Oxide Ceramic CM332 Grinding",
number = "3",
volume = "137",
doi = "10.1115/1.4029564"
}

Mladenović, G., Bojanić, P., Tanović, L.,& Klimenko, S.. (2015). Experimental Investigation of Microcutting Mechanisms in Oxide Ceramic CM332 Grinding. in Journal of Manufacturing Science and Engineering-Transactions of The Asme
ASME, New York., 137(3).
https://doi.org/10.1115/1.4029564

Mladenović G, Bojanić P, Tanović L, Klimenko S. Experimental Investigation of Microcutting Mechanisms in Oxide Ceramic CM332 Grinding. in Journal of Manufacturing Science and Engineering-Transactions of The Asme. 2015;137(3).
doi:10.1115/1.4029564 .

Mladenović, Goran, Bojanić, Pavao, Tanović, Ljubodrag, Klimenko, Sergey, "Experimental Investigation of Microcutting Mechanisms in Oxide Ceramic CM332 Grinding" in Journal of Manufacturing Science and Engineering-Transactions of The Asme, 137, no. 3 (2015),
https://doi.org/10.1115/1.4029564 . .

TY  - JOUR
AU  - Tanović, Ljubodrag
AU  - Bojanić, Pavao
AU  - Popović, Mihajlo
AU  - Belić, Zivorad
AU  - Trifković, Spasoje
PY  - 2012
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/1366
AB  - The paper presents an experimental study of micro-cutting intended to aid the optimization of the grinding process of the oxide-carbide ceramic BOK 60. The necessity for investigating the mechanisms occurring between the abrasive material and the ceramic is imposed by the fact that grinding is the dominant technology used to achieve the required quality of the workpiece surface finish. The investigations were carried out to determine the normal and tangential cutting forces, the critical penetration depth, and the crack generation angle on the workpiece surface as a function of the grain penetration speed and depth. The micro-cutting process was performed with a single diamond cone-shaped grain at varying depths of cut. It was found that the critical grain penetration depth separating ductile flow from brittle fracturing ranges from 3 to 5 mu m, while radial cracks on the ceramic's surface are distributed at an angle from 35A degrees to 75A degrees, measured relative to the direction of the diamond grain's motion.
PB  - Springer London Ltd, London
T2  - International Journal of Advanced Manufacturing Technology
T1  - Mechanisms in oxide-carbide ceramic BOK 60 grinding
EP  - 989
IS  - 9-12
SP  - 985
VL  - 58
DO  - 10.1007/s00170-011-3449-5
ER  - 

@article{
author = "Tanović, Ljubodrag and Bojanić, Pavao and Popović, Mihajlo and Belić, Zivorad and Trifković, Spasoje",
year = "2012",
abstract = "The paper presents an experimental study of micro-cutting intended to aid the optimization of the grinding process of the oxide-carbide ceramic BOK 60. The necessity for investigating the mechanisms occurring between the abrasive material and the ceramic is imposed by the fact that grinding is the dominant technology used to achieve the required quality of the workpiece surface finish. The investigations were carried out to determine the normal and tangential cutting forces, the critical penetration depth, and the crack generation angle on the workpiece surface as a function of the grain penetration speed and depth. The micro-cutting process was performed with a single diamond cone-shaped grain at varying depths of cut. It was found that the critical grain penetration depth separating ductile flow from brittle fracturing ranges from 3 to 5 mu m, while radial cracks on the ceramic's surface are distributed at an angle from 35A degrees to 75A degrees, measured relative to the direction of the diamond grain's motion.",
publisher = "Springer London Ltd, London",
journal = "International Journal of Advanced Manufacturing Technology",
title = "Mechanisms in oxide-carbide ceramic BOK 60 grinding",
pages = "989-985",
number = "9-12",
volume = "58",
doi = "10.1007/s00170-011-3449-5"
}

Tanović, L., Bojanić, P., Popović, M., Belić, Z.,& Trifković, S.. (2012). Mechanisms in oxide-carbide ceramic BOK 60 grinding. in International Journal of Advanced Manufacturing Technology
Springer London Ltd, London., 58(9-12), 985-989.
https://doi.org/10.1007/s00170-011-3449-5

Tanović L, Bojanić P, Popović M, Belić Z, Trifković S. Mechanisms in oxide-carbide ceramic BOK 60 grinding. in International Journal of Advanced Manufacturing Technology. 2012;58(9-12):985-989.
doi:10.1007/s00170-011-3449-5 .

Tanović, Ljubodrag, Bojanić, Pavao, Popović, Mihajlo, Belić, Zivorad, Trifković, Spasoje, "Mechanisms in oxide-carbide ceramic BOK 60 grinding" in International Journal of Advanced Manufacturing Technology, 58, no. 9-12 (2012):985-989,
https://doi.org/10.1007/s00170-011-3449-5 . .

TY  - BOOK
AU  - Mladenović, Goran
AU  - Bojanić, Pavao
PY  - 2012
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/6905
AB  - Studenti trece godine Mašinskog fakulteta u Beogradu imaju mogucnost da kroz izborni predmet „CAD/CAM sistemi“ ovladaju znanjima o metodama i tehnikama izgradnje savremenih CAD/CAM sistema kao i u primeni istih u projektovanju proizvoda, projektovanju tehnologije izrade, simulaciji putanje alata, dobijanju CL file-a i generisanju upravljacke informacije za CNC mašine alatke. U cilju efikasnijeg rada sa studentima na vežbama ukazala se potreba za jednim ovakvim prirucnikom. On ce u mnogome olakšati i samostalni rad studenata iz ovog predmeta i van nastave. Imajuci u vidu da fakultet raspolaže sa licencom Pro/ENGINEER®, verzija Wildfire® 4.0, i da je na raspolaganju studentima na radnim stanicama to je ovim udžbenikom obuhvacen samo ovaj softver.

U prvom delu detaljno se razraduje problem izgradnje geometrijskog 3D modela koji se u suštini svodi, na danas vec, konvencionalne tehnike 3D modeliranja, koje su više manje zajednicke za sve moderne CAD/CAM sisteme. Detaljno se razradjuju najcešce korišcene funkcije oblikovanja modela radnog predmeta u Part modulu kao što su Extrude, Revolve, Blend, Shell, Hole, Round itd. Studentima se pored uobicajenog postupka izgradnje 3D modela na bazi Bulovih operacija nad geometrijskim primitivima, objašnjava i postupak izgradnje 3D modela kada na ulazu u proces geometrijskog modeliranja imamo rezultate fukcionalnih proracuna ili više 2D digitalnih slika, dobijenih skeniranjem magnetnom rezonancom (MRI), kompjuterskom tomografijom (CT) ili industrijskom kompjuterskom tomografijom (ICT).

Problem izgradnje modela sklopova, odnosno viših nivoa ugradnje, detaljno se razraduje u Assembly modulu. U okviru ovog modula moguce je direktno kreirati delove koje ulaze u strukturu sklopa ili da se importuju 3D modeli vec prethodno kreiranih delova sklopa, odnosno proizvoda. Posebna pažnja je posvecena kreiranju 3D modela pokretnih sklopova i simulaciji njihovog kretanja.

U drugom delu udžbenika obuhvacena je problematika CAM modula, odnosno Manufacturig modula, pocev od generisanja modela pripremka na osnovu referentnog modela izratka pa preko definisanja operacija, definisanje tehnoloških zahvata, simulacije kretanja alata, definisanja CL file-a do postprocesiranja i dobijanja NC koda za datu upravljacku jedinicu.

Svaki student na kraju kursa dobija zadatak da modelira neki radni predmet, da projektuje tehnologiju za izradu datog dela, da simulacijom proveri eventualne greske i kolizije, da generise NC program za obradni centar ILR HMC 500/40 sa upravljackom jedinicom FANUC serije O–M i da na kraju taj isti deo obradi.
PB  - Univerzitet u Beogradu - Mašinski fakultet
T2  - Univerzitet u Beogradu - Mašinski fakultet
T1  - CAD/CAM Sistemi - Prirucnik za vežbe  (Pro/ENGINEER - Prakticna primena)
UR  - https://hdl.handle.net/21.15107/rcub_machinery_6905
ER  - 

@book{
author = "Mladenović, Goran and Bojanić, Pavao",
year = "2012",
abstract = "Studenti trece godine Mašinskog fakulteta u Beogradu imaju mogucnost da kroz izborni predmet „CAD/CAM sistemi“ ovladaju znanjima o metodama i tehnikama izgradnje savremenih CAD/CAM sistema kao i u primeni istih u projektovanju proizvoda, projektovanju tehnologije izrade, simulaciji putanje alata, dobijanju CL file-a i generisanju upravljacke informacije za CNC mašine alatke. U cilju efikasnijeg rada sa studentima na vežbama ukazala se potreba za jednim ovakvim prirucnikom. On ce u mnogome olakšati i samostalni rad studenata iz ovog predmeta i van nastave. Imajuci u vidu da fakultet raspolaže sa licencom Pro/ENGINEER®, verzija Wildfire® 4.0, i da je na raspolaganju studentima na radnim stanicama to je ovim udžbenikom obuhvacen samo ovaj softver.

U prvom delu detaljno se razraduje problem izgradnje geometrijskog 3D modela koji se u suštini svodi, na danas vec, konvencionalne tehnike 3D modeliranja, koje su više manje zajednicke za sve moderne CAD/CAM sisteme. Detaljno se razradjuju najcešce korišcene funkcije oblikovanja modela radnog predmeta u Part modulu kao što su Extrude, Revolve, Blend, Shell, Hole, Round itd. Studentima se pored uobicajenog postupka izgradnje 3D modela na bazi Bulovih operacija nad geometrijskim primitivima, objašnjava i postupak izgradnje 3D modela kada na ulazu u proces geometrijskog modeliranja imamo rezultate fukcionalnih proracuna ili više 2D digitalnih slika, dobijenih skeniranjem magnetnom rezonancom (MRI), kompjuterskom tomografijom (CT) ili industrijskom kompjuterskom tomografijom (ICT).

Problem izgradnje modela sklopova, odnosno viših nivoa ugradnje, detaljno se razraduje u Assembly modulu. U okviru ovog modula moguce je direktno kreirati delove koje ulaze u strukturu sklopa ili da se importuju 3D modeli vec prethodno kreiranih delova sklopa, odnosno proizvoda. Posebna pažnja je posvecena kreiranju 3D modela pokretnih sklopova i simulaciji njihovog kretanja.

U drugom delu udžbenika obuhvacena je problematika CAM modula, odnosno Manufacturig modula, pocev od generisanja modela pripremka na osnovu referentnog modela izratka pa preko definisanja operacija, definisanje tehnoloških zahvata, simulacije kretanja alata, definisanja CL file-a do postprocesiranja i dobijanja NC koda za datu upravljacku jedinicu.

Svaki student na kraju kursa dobija zadatak da modelira neki radni predmet, da projektuje tehnologiju za izradu datog dela, da simulacijom proveri eventualne greske i kolizije, da generise NC program za obradni centar ILR HMC 500/40 sa upravljackom jedinicom FANUC serije O–M i da na kraju taj isti deo obradi.",
publisher = "Univerzitet u Beogradu - Mašinski fakultet",
journal = "Univerzitet u Beogradu - Mašinski fakultet",
title = "CAD/CAM Sistemi - Prirucnik za vežbe  (Pro/ENGINEER - Prakticna primena)",
url = "https://hdl.handle.net/21.15107/rcub_machinery_6905"
}

Mladenović, G.,& Bojanić, P.. (2012). CAD/CAM Sistemi - Prirucnik za vežbe  (Pro/ENGINEER - Prakticna primena). in Univerzitet u Beogradu - Mašinski fakultet
Univerzitet u Beogradu - Mašinski fakultet..
https://hdl.handle.net/21.15107/rcub_machinery_6905

Mladenović G, Bojanić P. CAD/CAM Sistemi - Prirucnik za vežbe  (Pro/ENGINEER - Prakticna primena). in Univerzitet u Beogradu - Mašinski fakultet. 2012;.
https://hdl.handle.net/21.15107/rcub_machinery_6905 .

Mladenović, Goran, Bojanić, Pavao, "CAD/CAM Sistemi - Prirucnik za vežbe  (Pro/ENGINEER - Prakticna primena)" in Univerzitet u Beogradu - Mašinski fakultet (2012),
https://hdl.handle.net/21.15107/rcub_machinery_6905 .

TY  - CONF
AU  - Tanović, Ljubodrag
AU  - Bojanić, Pavao
AU  - Glavonjić, Miloš
AU  - Milutinović, Dragan
AU  - Majstorović, Vidosav
AU  - Puzović, Radovan
AU  - Kokotović, Branko
AU  - Popović, Mihajlo
AU  - Živanović, Saša
AU  - Slavković, Nikola
AU  - Mladenović, Goran
AU  - Stojadinović, Slavenko
PY  - 2012
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/4704
AB  - Predmet istraživanja je nova generacija domaćih obradnih sistema, zajedno sa proizvodnim tehnologijama, koje su potrebne za razvoj tih obradnih sistema i za njihov nesmetani rad. Ključne oblasti istraživanja u ovim tehnologijama su mašine alatke, roboti, alati, tehnološki procesi i digitalni kvalitet. Istraživanja su usmerena ka tehnologijama otvorene arhitekture, u pogledu sistema upravljanja i programiranja, ali i u pogledu struktura ovih sistema, prateći aktuelna istraživanja u ovim oblastima. Tako se obezbeđuju fleksibilnost tehnoloških resursa i agilnost kompanija, kojima su i namenjeni ovi novi obradni sistemi, sa svojim pratećim tehnologijama. Ovde se daje pregled rezultata istraživanja za 2011. godinu.
PB  - Univerzitet u Beogradu, Mašinski fakultet, Katedra za proizvodno mašinstvo
C3  - Zbornik radova - 38. JUPITER konferenencija
T1  - Razvoj nove generacije domaćih obradnih sistema – rezultati istraživanja za 2011. godinu
EP  - UR.95
SP  - UR76
UR  - https://hdl.handle.net/21.15107/rcub_machinery_4704
ER  - 

@conference{
author = "Tanović, Ljubodrag and Bojanić, Pavao and Glavonjić, Miloš and Milutinović, Dragan and Majstorović, Vidosav and Puzović, Radovan and Kokotović, Branko and Popović, Mihajlo and Živanović, Saša and Slavković, Nikola and Mladenović, Goran and Stojadinović, Slavenko",
year = "2012",
abstract = "Predmet istraživanja je nova generacija domaćih obradnih sistema, zajedno sa proizvodnim tehnologijama, koje su potrebne za razvoj tih obradnih sistema i za njihov nesmetani rad. Ključne oblasti istraživanja u ovim tehnologijama su mašine alatke, roboti, alati, tehnološki procesi i digitalni kvalitet. Istraživanja su usmerena ka tehnologijama otvorene arhitekture, u pogledu sistema upravljanja i programiranja, ali i u pogledu struktura ovih sistema, prateći aktuelna istraživanja u ovim oblastima. Tako se obezbeđuju fleksibilnost tehnoloških resursa i agilnost kompanija, kojima su i namenjeni ovi novi obradni sistemi, sa svojim pratećim tehnologijama. Ovde se daje pregled rezultata istraživanja za 2011. godinu.",
publisher = "Univerzitet u Beogradu, Mašinski fakultet, Katedra za proizvodno mašinstvo",
journal = "Zbornik radova - 38. JUPITER konferenencija",
title = "Razvoj nove generacije domaćih obradnih sistema – rezultati istraživanja za 2011. godinu",
pages = "UR.95-UR76",
url = "https://hdl.handle.net/21.15107/rcub_machinery_4704"
}

Tanović, L., Bojanić, P., Glavonjić, M., Milutinović, D., Majstorović, V., Puzović, R., Kokotović, B., Popović, M., Živanović, S., Slavković, N., Mladenović, G.,& Stojadinović, S.. (2012). Razvoj nove generacije domaćih obradnih sistema – rezultati istraživanja za 2011. godinu. in Zbornik radova - 38. JUPITER konferenencija
Univerzitet u Beogradu, Mašinski fakultet, Katedra za proizvodno mašinstvo., UR76-UR.95.
https://hdl.handle.net/21.15107/rcub_machinery_4704

Tanović L, Bojanić P, Glavonjić M, Milutinović D, Majstorović V, Puzović R, Kokotović B, Popović M, Živanović S, Slavković N, Mladenović G, Stojadinović S. Razvoj nove generacije domaćih obradnih sistema – rezultati istraživanja za 2011. godinu. in Zbornik radova - 38. JUPITER konferenencija. 2012;:UR76-UR.95.
https://hdl.handle.net/21.15107/rcub_machinery_4704 .

Tanović, Ljubodrag, Bojanić, Pavao, Glavonjić, Miloš, Milutinović, Dragan, Majstorović, Vidosav, Puzović, Radovan, Kokotović, Branko, Popović, Mihajlo, Živanović, Saša, Slavković, Nikola, Mladenović, Goran, Stojadinović, Slavenko, "Razvoj nove generacije domaćih obradnih sistema – rezultati istraživanja za 2011. godinu" in Zbornik radova - 38. JUPITER konferenencija (2012):UR76-UR.95,
https://hdl.handle.net/21.15107/rcub_machinery_4704 .

TY  - CONF
AU  - Tanović, Ljubodrag
AU  - Bojanić, Pavao
AU  - Popović, Mihajlo
AU  - Mladenović, Goran
PY  - 2012
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/6083
AB  - Istraživanja u oblasti razvoja nove generacije mašina alatki za mikroproizvodnju komponenti dimenzija do nekoliko milimetara, izradjenih sa visokom tačnošću od različitih materijala podrazumeva neophodnost poznavanja procesa koji su prisutni kod takvih sistema - mikroprocesa. Mehanizam formiranja strugotine u mikro procesima rezanja je sasvim različit u odnosu na makro, uz napomenu da postoji odredjen broj fenomena koji su u mnogim slučajevima i protivurečni U radu je prikazan deo istraživanja koji se realizuje u oblasti mikrorezanja oksidno-karbidne keramike na Mašinskom fakultetu na katedri za proizvodno mašinstvo.
PB  - The union of engineers of Montenegro
PB  - Maintainers society of Montenegro
PB  - Cooperative training center faculty of Mechanical engineering Podgorica
C3  - Proceedings - X International Conference Maintenance and Production Engineering ,,KODIP - 2012''
T1  - Mechanical micro manufacturing processes
T1  - Mehanički mikroobradni procesi
EP  - 53
SP  - 47
UR  - https://hdl.handle.net/21.15107/rcub_machinery_6083
ER  - 

@conference{
author = "Tanović, Ljubodrag and Bojanić, Pavao and Popović, Mihajlo and Mladenović, Goran",
year = "2012",
abstract = "Istraživanja u oblasti razvoja nove generacije mašina alatki za mikroproizvodnju komponenti dimenzija do nekoliko milimetara, izradjenih sa visokom tačnošću od različitih materijala podrazumeva neophodnost poznavanja procesa koji su prisutni kod takvih sistema - mikroprocesa. Mehanizam formiranja strugotine u mikro procesima rezanja je sasvim različit u odnosu na makro, uz napomenu da postoji odredjen broj fenomena koji su u mnogim slučajevima i protivurečni U radu je prikazan deo istraživanja koji se realizuje u oblasti mikrorezanja oksidno-karbidne keramike na Mašinskom fakultetu na katedri za proizvodno mašinstvo.",
publisher = "The union of engineers of Montenegro, Maintainers society of Montenegro, Cooperative training center faculty of Mechanical engineering Podgorica",
journal = "Proceedings - X International Conference Maintenance and Production Engineering ,,KODIP - 2012''",
title = "Mechanical micro manufacturing processes, Mehanički mikroobradni procesi",
pages = "53-47",
url = "https://hdl.handle.net/21.15107/rcub_machinery_6083"
}

Tanović, L., Bojanić, P., Popović, M.,& Mladenović, G.. (2012). Mechanical micro manufacturing processes. in Proceedings - X International Conference Maintenance and Production Engineering ,,KODIP - 2012''
The union of engineers of Montenegro., 47-53.
https://hdl.handle.net/21.15107/rcub_machinery_6083

Tanović L, Bojanić P, Popović M, Mladenović G. Mechanical micro manufacturing processes. in Proceedings - X International Conference Maintenance and Production Engineering ,,KODIP - 2012''. 2012;:47-53.
https://hdl.handle.net/21.15107/rcub_machinery_6083 .

Tanović, Ljubodrag, Bojanić, Pavao, Popović, Mihajlo, Mladenović, Goran, "Mechanical micro manufacturing processes" in Proceedings - X International Conference Maintenance and Production Engineering ,,KODIP - 2012'' (2012):47-53,
https://hdl.handle.net/21.15107/rcub_machinery_6083 .

TY  - CONF
AU  - Bojanić, Pavao
AU  - Mladenović, Goran
PY  - 2011
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/6946
AB  - Kod abrade radnih predmeta sa skulptorskim površinama na CNC mašinama alatkama, putanja alata je ključni element za kvalitet obrađene površine  i za efikasnost abrade. U radu se daje opšta analiza problema i pravaca rešavanja u generisanju putanje alata pri obradi skulptorskih površina. Definisani su kriterijumi za optimizaciju pri generisanju putanje alata.
PB  - Univerzitet u Beogradu - Mašinski fakultet
C3  - 37. JUPITER Konferencija, 24. simpozijum CAD/CAM
T1  - Analiza problema pri generisanju putanje alata pri obradi skulptorskih površina
EP  - 2.62
SP  - 2.57
UR  - https://hdl.handle.net/21.15107/rcub_machinery_6946
ER  - 

@conference{
author = "Bojanić, Pavao and Mladenović, Goran",
year = "2011",
abstract = "Kod abrade radnih predmeta sa skulptorskim površinama na CNC mašinama alatkama, putanja alata je ključni element za kvalitet obrađene površine  i za efikasnost abrade. U radu se daje opšta analiza problema i pravaca rešavanja u generisanju putanje alata pri obradi skulptorskih površina. Definisani su kriterijumi za optimizaciju pri generisanju putanje alata.",
publisher = "Univerzitet u Beogradu - Mašinski fakultet",
journal = "37. JUPITER Konferencija, 24. simpozijum CAD/CAM",
title = "Analiza problema pri generisanju putanje alata pri obradi skulptorskih površina",
pages = "2.62-2.57",
url = "https://hdl.handle.net/21.15107/rcub_machinery_6946"
}

Bojanić, P.,& Mladenović, G.. (2011). Analiza problema pri generisanju putanje alata pri obradi skulptorskih površina. in 37. JUPITER Konferencija, 24. simpozijum CAD/CAM
Univerzitet u Beogradu - Mašinski fakultet., 2.57-2.62.
https://hdl.handle.net/21.15107/rcub_machinery_6946

Bojanić P, Mladenović G. Analiza problema pri generisanju putanje alata pri obradi skulptorskih površina. in 37. JUPITER Konferencija, 24. simpozijum CAD/CAM. 2011;:2.57-2.62.
https://hdl.handle.net/21.15107/rcub_machinery_6946 .

Bojanić, Pavao, Mladenović, Goran, "Analiza problema pri generisanju putanje alata pri obradi skulptorskih površina" in 37. JUPITER Konferencija, 24. simpozijum CAD/CAM (2011):2.57-2.62,
https://hdl.handle.net/21.15107/rcub_machinery_6946 .

TY  - JOUR
AU  - Tanović, Ljubodrag
AU  - Bojanić, Pavao
AU  - Puzović, Radovan
AU  - Milutinović, M.
PY  - 2011
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/1161
AB  - This paper shows the results of investigations performed in the brittle materials microcutting at the Faculty of Mechanical Engineering, Belgrade University. The interactions between a single diamond grain and the machined granite are analyzed. The change in the normal cutting force as a function of grain penetration speed and depth was experimentally established in microcutting of two types of granite originating from Serbia. Based on the grain traces on granite and the generated cracks, the critical grain penetration depth for the formation of brittle fracturing was established. The experiments are intended to assist in the optimization of the grinding process as technology dominant in the granite finishing. [DOI: 10.1115/1.4003521]
PB  - Asme-Amer Soc Mechanical Eng, New York
T2  - Journal of Manufacturing Science and Engineering-Transactions of The Asme
T1  - Experimental Investigation of Microcutting Mechanisms in Granite Grinding
IS  - 2
VL  - 133
DO  - 10.1115/1.4003521
ER  - 

@article{
author = "Tanović, Ljubodrag and Bojanić, Pavao and Puzović, Radovan and Milutinović, M.",
year = "2011",
abstract = "This paper shows the results of investigations performed in the brittle materials microcutting at the Faculty of Mechanical Engineering, Belgrade University. The interactions between a single diamond grain and the machined granite are analyzed. The change in the normal cutting force as a function of grain penetration speed and depth was experimentally established in microcutting of two types of granite originating from Serbia. Based on the grain traces on granite and the generated cracks, the critical grain penetration depth for the formation of brittle fracturing was established. The experiments are intended to assist in the optimization of the grinding process as technology dominant in the granite finishing. [DOI: 10.1115/1.4003521]",
publisher = "Asme-Amer Soc Mechanical Eng, New York",
journal = "Journal of Manufacturing Science and Engineering-Transactions of The Asme",
title = "Experimental Investigation of Microcutting Mechanisms in Granite Grinding",
number = "2",
volume = "133",
doi = "10.1115/1.4003521"
}

Tanović, L., Bojanić, P., Puzović, R.,& Milutinović, M.. (2011). Experimental Investigation of Microcutting Mechanisms in Granite Grinding. in Journal of Manufacturing Science and Engineering-Transactions of The Asme
Asme-Amer Soc Mechanical Eng, New York., 133(2).
https://doi.org/10.1115/1.4003521

Tanović L, Bojanić P, Puzović R, Milutinović M. Experimental Investigation of Microcutting Mechanisms in Granite Grinding. in Journal of Manufacturing Science and Engineering-Transactions of The Asme. 2011;133(2).
doi:10.1115/1.4003521 .

Tanović, Ljubodrag, Bojanić, Pavao, Puzović, Radovan, Milutinović, M., "Experimental Investigation of Microcutting Mechanisms in Granite Grinding" in Journal of Manufacturing Science and Engineering-Transactions of The Asme, 133, no. 2 (2011),
https://doi.org/10.1115/1.4003521 . .

TY  - CONF
AU  - Tanović, Ljubodrag
AU  - Bojanić, Pavao
AU  - Puzović, Radovan
AU  - Popović, Mihajlo
AU  - Mladenović, Goran
PY  - 2011
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/6927
AB  - The paper presents the results of to date investigations in the field of ornamental stone micro-cutting using the examples of granite and marble originating from the stone varieties of Serbian location. The diamond grain - machined stone (the "Josanica" granite and the "Plavi tok" marble) interaction was analyzed. The analysis also embraced the changes of the normal cutting force as a function of cutting speed and grain penetration depth in the chosen stone. Based on the grain traces (cracks) that occurred on the surface of the machined stone, the critical cutting depths, at which brittle cutting occurs, were established for the mentioned stones. The presented analysis is to be used for the grinding process optimization as a dominant ornamental stone machining technology with the aim of obtaining quality machined surfaces and preserving the stone surface structure and color.
PB  - Niš : Faculty of Mechanical Engineering
C3  - 34th International Conference on Production Engineering, 28.30. September, Niš, Serbia
T1  - Analysis of stone micro-cutting mechanism using the example of granite and marble grinding
EP  - 44
SP  - 41
UR  - https://hdl.handle.net/21.15107/rcub_machinery_6927
ER  - 

@conference{
author = "Tanović, Ljubodrag and Bojanić, Pavao and Puzović, Radovan and Popović, Mihajlo and Mladenović, Goran",
year = "2011",
abstract = "The paper presents the results of to date investigations in the field of ornamental stone micro-cutting using the examples of granite and marble originating from the stone varieties of Serbian location. The diamond grain - machined stone (the "Josanica" granite and the "Plavi tok" marble) interaction was analyzed. The analysis also embraced the changes of the normal cutting force as a function of cutting speed and grain penetration depth in the chosen stone. Based on the grain traces (cracks) that occurred on the surface of the machined stone, the critical cutting depths, at which brittle cutting occurs, were established for the mentioned stones. The presented analysis is to be used for the grinding process optimization as a dominant ornamental stone machining technology with the aim of obtaining quality machined surfaces and preserving the stone surface structure and color.",
publisher = "Niš : Faculty of Mechanical Engineering",
journal = "34th International Conference on Production Engineering, 28.30. September, Niš, Serbia",
title = "Analysis of stone micro-cutting mechanism using the example of granite and marble grinding",
pages = "44-41",
url = "https://hdl.handle.net/21.15107/rcub_machinery_6927"
}

Tanović, L., Bojanić, P., Puzović, R., Popović, M.,& Mladenović, G.. (2011). Analysis of stone micro-cutting mechanism using the example of granite and marble grinding. in 34th International Conference on Production Engineering, 28.30. September, Niš, Serbia
Niš : Faculty of Mechanical Engineering., 41-44.
https://hdl.handle.net/21.15107/rcub_machinery_6927

Tanović L, Bojanić P, Puzović R, Popović M, Mladenović G. Analysis of stone micro-cutting mechanism using the example of granite and marble grinding. in 34th International Conference on Production Engineering, 28.30. September, Niš, Serbia. 2011;:41-44.
https://hdl.handle.net/21.15107/rcub_machinery_6927 .

Tanović, Ljubodrag, Bojanić, Pavao, Puzović, Radovan, Popović, Mihajlo, Mladenović, Goran, "Analysis of stone micro-cutting mechanism using the example of granite and marble grinding" in 34th International Conference on Production Engineering, 28.30. September, Niš, Serbia (2011):41-44,
https://hdl.handle.net/21.15107/rcub_machinery_6927 .

TY  - JOUR
AU  - Tanović, Ljubodrag
AU  - Bojanić, Pavao
AU  - Popović, Mihajlo
AU  - Mladenović, Goran
PY  - 2011
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/6943
AB  - In this work results are indicated researches, conducted on the Machine-building faculty in Belgrade in area of micro cutting of fragile materials. Co-operation is here analyzed between diamond grain and processed granite. The change of normal making force of cutting in the function of speed of cutting and depth of penetration at micro cutting of two variants of granites is experimentally set from the location of Serbia. On the basis of tracks on a granite and arising up cracks the critical depth of penetration of grain is set, which fragile destruction is at. The indicated researches must help optimization of process of polishing and polish, being dominant technologies of final treatment of granite.
PB  - Kyiv : National Technical University of Ukraine "Igor Sikorsky Kyiv Polytechnic Institute"
T2  - Висник Машинобудування
T1  - Специфичности микрорезания камня на основе гранита
EP  - 102
SP  - 99
VL  - 63
UR  - https://hdl.handle.net/21.15107/rcub_machinery_6943
ER  - 

@article{
author = "Tanović, Ljubodrag and Bojanić, Pavao and Popović, Mihajlo and Mladenović, Goran",
year = "2011",
abstract = "In this work results are indicated researches, conducted on the Machine-building faculty in Belgrade in area of micro cutting of fragile materials. Co-operation is here analyzed between diamond grain and processed granite. The change of normal making force of cutting in the function of speed of cutting and depth of penetration at micro cutting of two variants of granites is experimentally set from the location of Serbia. On the basis of tracks on a granite and arising up cracks the critical depth of penetration of grain is set, which fragile destruction is at. The indicated researches must help optimization of process of polishing and polish, being dominant technologies of final treatment of granite.",
publisher = "Kyiv : National Technical University of Ukraine "Igor Sikorsky Kyiv Polytechnic Institute"",
journal = "Висник Машинобудування",
title = "Специфичности микрорезания камня на основе гранита",
pages = "102-99",
volume = "63",
url = "https://hdl.handle.net/21.15107/rcub_machinery_6943"
}

Tanović, L., Bojanić, P., Popović, M.,& Mladenović, G.. (2011). Специфичности микрорезания камня на основе гранита. in Висник Машинобудування
Kyiv : National Technical University of Ukraine "Igor Sikorsky Kyiv Polytechnic Institute"., 63, 99-102.
https://hdl.handle.net/21.15107/rcub_machinery_6943

Tanović L, Bojanić P, Popović M, Mladenović G. Специфичности микрорезания камня на основе гранита. in Висник Машинобудування. 2011;63:99-102.
https://hdl.handle.net/21.15107/rcub_machinery_6943 .

Tanović, Ljubodrag, Bojanić, Pavao, Popović, Mihajlo, Mladenović, Goran, "Специфичности микрорезания камня на основе гранита" in Висник Машинобудування, 63 (2011):99-102,
https://hdl.handle.net/21.15107/rcub_machinery_6943 .

TY  - CONF
AU  - Tanović, Ljubodrag
AU  - Bojanić, Pavao
AU  - Popović, Mihajlo
AU  - Mladenović, Goran
PY  - 2011
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/6929
PB  - Житомирський державний технологічний університет, Житомир
C3  - VII Международная научно-техническая конференция “Процеси Механiчної Обробки в Машинобудуванні 2011
T1  - СПЕЦИФИKA МИКРОРЕЗАНИЯ ГРАНИТА
EP  - 338
SP  - 328
UR  - https://hdl.handle.net/21.15107/rcub_machinery_6929
ER  - 

@conference{
author = "Tanović, Ljubodrag and Bojanić, Pavao and Popović, Mihajlo and Mladenović, Goran",
year = "2011",
publisher = "Житомирський державний технологічний університет, Житомир",
journal = "VII Международная научно-техническая конференция “Процеси Механiчної Обробки в Машинобудуванні 2011",
title = "СПЕЦИФИKA МИКРОРЕЗАНИЯ ГРАНИТА",
pages = "338-328",
url = "https://hdl.handle.net/21.15107/rcub_machinery_6929"
}

Tanović, L., Bojanić, P., Popović, M.,& Mladenović, G.. (2011). СПЕЦИФИKA МИКРОРЕЗАНИЯ ГРАНИТА. in VII Международная научно-техническая конференция “Процеси Механiчної Обробки в Машинобудуванні 2011
Житомирський державний технологічний університет, Житомир., 328-338.
https://hdl.handle.net/21.15107/rcub_machinery_6929

Tanović L, Bojanić P, Popović M, Mladenović G. СПЕЦИФИKA МИКРОРЕЗАНИЯ ГРАНИТА. in VII Международная научно-техническая конференция “Процеси Механiчної Обробки в Машинобудуванні 2011. 2011;:328-338.
https://hdl.handle.net/21.15107/rcub_machinery_6929 .

Tanović, Ljubodrag, Bojanić, Pavao, Popović, Mihajlo, Mladenović, Goran, "СПЕЦИФИKA МИКРОРЕЗАНИЯ ГРАНИТА" in VII Международная научно-техническая конференция “Процеси Механiчної Обробки в Машинобудуванні 2011 (2011):328-338,
https://hdl.handle.net/21.15107/rcub_machinery_6929 .

TY  - CONF
AU  - Milutinović, Dragan
AU  - Glavonjić, Miloš
AU  - Tanović, Ljubodrag
AU  - Bojanić, Pavao
AU  - Puzović, Radovan
AU  - Živanović, Saša
AU  - Kokotović, Branko
AU  - Popović, Mihajlo
AU  - Slavković, Nikola
AU  - Mladenović, Goran
PY  - 2011
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/4814
AB  - U radu je prikazan deo rezultata istraživanja u oblasti nove generacije obradnih sistema. Prikazom  su obuhvaćeni razvijeni prototipovi mašina alatki i robota sa paralelnom kinematikom, kao i rekonfigurabilni obradni sistem za višeosnu obradu na bazi robota. Prikazani rezultati predstavljaju osnovu za saradnju sa domaćom industrijom, ucešće u međunarodnim projektima i dalja  istraživanja. Razvijeni sistemi takođe čine i resurs za laboratorijski rad studenata proizvodnog mačinstva na svim nivoima studija.
PB  - Univerzitet u Beogradu, Mašinski fakultet, Katedra za proizvodno mašinstvo
C3  - Zbornik radova - 37. JUPITER konferenencija
T1  - Rezultati istraživanja i razvoja nove generacije obradnih sistema
EP  - UR64
SP  - UR51
UR  - https://hdl.handle.net/21.15107/rcub_machinery_4814
ER  - 

@conference{
author = "Milutinović, Dragan and Glavonjić, Miloš and Tanović, Ljubodrag and Bojanić, Pavao and Puzović, Radovan and Živanović, Saša and Kokotović, Branko and Popović, Mihajlo and Slavković, Nikola and Mladenović, Goran",
year = "2011",
abstract = "U radu je prikazan deo rezultata istraživanja u oblasti nove generacije obradnih sistema. Prikazom  su obuhvaćeni razvijeni prototipovi mašina alatki i robota sa paralelnom kinematikom, kao i rekonfigurabilni obradni sistem za višeosnu obradu na bazi robota. Prikazani rezultati predstavljaju osnovu za saradnju sa domaćom industrijom, ucešće u međunarodnim projektima i dalja  istraživanja. Razvijeni sistemi takođe čine i resurs za laboratorijski rad studenata proizvodnog mačinstva na svim nivoima studija.",
publisher = "Univerzitet u Beogradu, Mašinski fakultet, Katedra za proizvodno mašinstvo",
journal = "Zbornik radova - 37. JUPITER konferenencija",
title = "Rezultati istraživanja i razvoja nove generacije obradnih sistema",
pages = "UR64-UR51",
url = "https://hdl.handle.net/21.15107/rcub_machinery_4814"
}

Milutinović, D., Glavonjić, M., Tanović, L., Bojanić, P., Puzović, R., Živanović, S., Kokotović, B., Popović, M., Slavković, N.,& Mladenović, G.. (2011). Rezultati istraživanja i razvoja nove generacije obradnih sistema. in Zbornik radova - 37. JUPITER konferenencija
Univerzitet u Beogradu, Mašinski fakultet, Katedra za proizvodno mašinstvo., UR51-UR64.
https://hdl.handle.net/21.15107/rcub_machinery_4814

Milutinović D, Glavonjić M, Tanović L, Bojanić P, Puzović R, Živanović S, Kokotović B, Popović M, Slavković N, Mladenović G. Rezultati istraživanja i razvoja nove generacije obradnih sistema. in Zbornik radova - 37. JUPITER konferenencija. 2011;:UR51-UR64.
https://hdl.handle.net/21.15107/rcub_machinery_4814 .

Milutinović, Dragan, Glavonjić, Miloš, Tanović, Ljubodrag, Bojanić, Pavao, Puzović, Radovan, Živanović, Saša, Kokotović, Branko, Popović, Mihajlo, Slavković, Nikola, Mladenović, Goran, "Rezultati istraživanja i razvoja nove generacije obradnih sistema" in Zbornik radova - 37. JUPITER konferenencija (2011):UR51-UR64,
https://hdl.handle.net/21.15107/rcub_machinery_4814 .

TY  - CONF
AU  - Tanović, Ljubodrag
AU  - Bojanić, Pavao
AU  - Puzović, Radovan
AU  - Popović, Mihajlo
AU  - Mladenović, Goran
PY  - 2011
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/6099
AB  - U radu su prikazani osnovni principi projektovanja proizvoda od polimernih materijala koji se oblikuju livenjem pod pritiskom, kao i osnovni principi projektovanja odgovarajućih alata za njihovo oblikovanje. Imajući u vidu da su zadaci projektovanja spomenutih delova i alata i obrada potrebnih udubljenja u alatima vrlo složen zadatak i u nekim slučajevima je potrebna i izrada prototipova, ovde je data analiza mogućnosti primene CA (Computer Aided) alata u navedenim aktivnostima kroz neke primere primene. Cilj analize je da pokaže u kojoj su meri raspoloživi CA alati u mogućnosti da potpomognu automatizaciju projektovanje proizvoda od polimernih materijala i projektovanje i izradu alata za oblikovanje takvih delova livenjem pod pritiskom. Kao i to u kojoj meri je primena simulacionih modela adekvatna zamena za izradu prototipova.
AB  - The paper presents the basic design principles of polymer products molded by pressure casting, as well as the basic principles of appropriate tools design for their molding. Taking into account that the design tasks of mentioned parts and tools as well as machining of required dents in tools is a very complex task and that in some cases the prototypes are required to be made, the paper gives the analysis of the possibilities of applying the CA (Computer Aided) tools in mentioned activities through some examples of application. The aim of the analysis is to demonstrate how much the available CA tools can help the automation of polymeric material product design, and tool design and manufacture for molding such products by pressure casting. Also, the paper shows the degree to which the application of simulation models is an adequate substitution in prototype making.
PB  - Beograd : Univerzitet u Beogradu - Mašinski fakultet
C3  - Zbornik radova, 37. JUPITER konferencija, 24. simpozijum CAD/CAM
T1  - Primena CAD/CAM/CAE programskog paketa pri projektovanju i izradi alata za livenje pod pritiskom delova od polimera
T1  - The application of the CAD/CAM/CAE program package in the design and manufacturing of casting pressure tools for parts made from polymers
EP  - 2.29
SP  - 2.22
UR  - https://hdl.handle.net/21.15107/rcub_machinery_6099
ER  - 

@conference{
author = "Tanović, Ljubodrag and Bojanić, Pavao and Puzović, Radovan and Popović, Mihajlo and Mladenović, Goran",
year = "2011",
abstract = "U radu su prikazani osnovni principi projektovanja proizvoda od polimernih materijala koji se oblikuju livenjem pod pritiskom, kao i osnovni principi projektovanja odgovarajućih alata za njihovo oblikovanje. Imajući u vidu da su zadaci projektovanja spomenutih delova i alata i obrada potrebnih udubljenja u alatima vrlo složen zadatak i u nekim slučajevima je potrebna i izrada prototipova, ovde je data analiza mogućnosti primene CA (Computer Aided) alata u navedenim aktivnostima kroz neke primere primene. Cilj analize je da pokaže u kojoj su meri raspoloživi CA alati u mogućnosti da potpomognu automatizaciju projektovanje proizvoda od polimernih materijala i projektovanje i izradu alata za oblikovanje takvih delova livenjem pod pritiskom. Kao i to u kojoj meri je primena simulacionih modela adekvatna zamena za izradu prototipova., The paper presents the basic design principles of polymer products molded by pressure casting, as well as the basic principles of appropriate tools design for their molding. Taking into account that the design tasks of mentioned parts and tools as well as machining of required dents in tools is a very complex task and that in some cases the prototypes are required to be made, the paper gives the analysis of the possibilities of applying the CA (Computer Aided) tools in mentioned activities through some examples of application. The aim of the analysis is to demonstrate how much the available CA tools can help the automation of polymeric material product design, and tool design and manufacture for molding such products by pressure casting. Also, the paper shows the degree to which the application of simulation models is an adequate substitution in prototype making.",
publisher = "Beograd : Univerzitet u Beogradu - Mašinski fakultet",
journal = "Zbornik radova, 37. JUPITER konferencija, 24. simpozijum CAD/CAM",
title = "Primena CAD/CAM/CAE programskog paketa pri projektovanju i izradi alata za livenje pod pritiskom delova od polimera, The application of the CAD/CAM/CAE program package in the design and manufacturing of casting pressure tools for parts made from polymers",
pages = "2.29-2.22",
url = "https://hdl.handle.net/21.15107/rcub_machinery_6099"
}

Tanović, L., Bojanić, P., Puzović, R., Popović, M.,& Mladenović, G.. (2011). Primena CAD/CAM/CAE programskog paketa pri projektovanju i izradi alata za livenje pod pritiskom delova od polimera. in Zbornik radova, 37. JUPITER konferencija, 24. simpozijum CAD/CAM
Beograd : Univerzitet u Beogradu - Mašinski fakultet., 2.22-2.29.
https://hdl.handle.net/21.15107/rcub_machinery_6099

Tanović L, Bojanić P, Puzović R, Popović M, Mladenović G. Primena CAD/CAM/CAE programskog paketa pri projektovanju i izradi alata za livenje pod pritiskom delova od polimera. in Zbornik radova, 37. JUPITER konferencija, 24. simpozijum CAD/CAM. 2011;:2.22-2.29.
https://hdl.handle.net/21.15107/rcub_machinery_6099 .

Tanović, Ljubodrag, Bojanić, Pavao, Puzović, Radovan, Popović, Mihajlo, Mladenović, Goran, "Primena CAD/CAM/CAE programskog paketa pri projektovanju i izradi alata za livenje pod pritiskom delova od polimera" in Zbornik radova, 37. JUPITER konferencija, 24. simpozijum CAD/CAM (2011):2.22-2.29,
https://hdl.handle.net/21.15107/rcub_machinery_6099 .

TY  - JOUR
AU  - Tanović, Ljubodrag
AU  - Bojanić, Pavao
AU  - Puzović, Radovan
AU  - Klimenko, Sergey
PY  - 2011
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/1200
AB  - The paper presents PCBN-Ciborit cutting tools life and wear test results. The effects of the machining regime when turning amorphous-crystalline Fe80B20 and Fe79Cr16B5 coating systems applied to conventional workpiece materials were assessed. It has been shown that the observed tool wear mechanisms are complex in their character and are dominated by abrasive-mechanical, adhesive and chemical effects in the cutting zone. Under changing turning conditions tool life is affected by the structural-phase composition and by the non-homogeneous structure of the coating. Specifically, when turning gas-flame coatings deposited with a Fe80B20 electrode and electro-arc coatings with a Fe79Cr16B5 electrode the lowest wear and the highest tool life was achieved at cutting speeds of nu = 1.1 to 1.2 m/s and a back rake angle of gamma = -10 degrees It has been demonstrated that a change of the back rake angle from gamma = 0 to -10 degrees does not have a great effect on tool life contraty to the case with gamma = -20 degrees.
PB  - Assoc Mechanical Engineers Technicians Slovenia, Ljubljana
T2  - Strojniski Vestnik-Journal of Mechanical Engineering
T1  - Polycrystalline Cubic Boron Nitride (PCBN) Tool Life and Wear in Turning of Amorphous-Crystalline Iron-Based Coatings
EP  - 910
IS  - 12
SP  - 904
VL  - 57
DO  - 10.5545/sv-jme.2011.010
ER  - 

@article{
author = "Tanović, Ljubodrag and Bojanić, Pavao and Puzović, Radovan and Klimenko, Sergey",
year = "2011",
abstract = "The paper presents PCBN-Ciborit cutting tools life and wear test results. The effects of the machining regime when turning amorphous-crystalline Fe80B20 and Fe79Cr16B5 coating systems applied to conventional workpiece materials were assessed. It has been shown that the observed tool wear mechanisms are complex in their character and are dominated by abrasive-mechanical, adhesive and chemical effects in the cutting zone. Under changing turning conditions tool life is affected by the structural-phase composition and by the non-homogeneous structure of the coating. Specifically, when turning gas-flame coatings deposited with a Fe80B20 electrode and electro-arc coatings with a Fe79Cr16B5 electrode the lowest wear and the highest tool life was achieved at cutting speeds of nu = 1.1 to 1.2 m/s and a back rake angle of gamma = -10 degrees It has been demonstrated that a change of the back rake angle from gamma = 0 to -10 degrees does not have a great effect on tool life contraty to the case with gamma = -20 degrees.",
publisher = "Assoc Mechanical Engineers Technicians Slovenia, Ljubljana",
journal = "Strojniski Vestnik-Journal of Mechanical Engineering",
title = "Polycrystalline Cubic Boron Nitride (PCBN) Tool Life and Wear in Turning of Amorphous-Crystalline Iron-Based Coatings",
pages = "910-904",
number = "12",
volume = "57",
doi = "10.5545/sv-jme.2011.010"
}

Tanović, L., Bojanić, P., Puzović, R.,& Klimenko, S.. (2011). Polycrystalline Cubic Boron Nitride (PCBN) Tool Life and Wear in Turning of Amorphous-Crystalline Iron-Based Coatings. in Strojniski Vestnik-Journal of Mechanical Engineering
Assoc Mechanical Engineers Technicians Slovenia, Ljubljana., 57(12), 904-910.
https://doi.org/10.5545/sv-jme.2011.010

Tanović L, Bojanić P, Puzović R, Klimenko S. Polycrystalline Cubic Boron Nitride (PCBN) Tool Life and Wear in Turning of Amorphous-Crystalline Iron-Based Coatings. in Strojniski Vestnik-Journal of Mechanical Engineering. 2011;57(12):904-910.
doi:10.5545/sv-jme.2011.010 .

Tanović, Ljubodrag, Bojanić, Pavao, Puzović, Radovan, Klimenko, Sergey, "Polycrystalline Cubic Boron Nitride (PCBN) Tool Life and Wear in Turning of Amorphous-Crystalline Iron-Based Coatings" in Strojniski Vestnik-Journal of Mechanical Engineering, 57, no. 12 (2011):904-910,
https://doi.org/10.5545/sv-jme.2011.010 . .

TY  - GEN
AU  - Tanović, Ljubodrag
AU  - Bojanić, Pavao
AU  - Puzović, Radovan
AU  - Popović, Mihajlo
AU  - Milutinović, Milan
AU  - Mladenović, Goran
PY  - 2010
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/6950
AB  - Tehničko rešenje pripada oblasti novih metoda u domenu proizvodnih tehnologija.
PB  - Univerzitet u Beogradu - Mašinski fakultet
T2  - Univerzitet u Beogradu - Mašinski fakultet
T1  - Nova metoda projektovanja i tehnologije izrade profilnih prizmatičnih – tangencijalnih strugarskih noževa
UR  - https://hdl.handle.net/21.15107/rcub_machinery_6950
ER  - 

@misc{
author = "Tanović, Ljubodrag and Bojanić, Pavao and Puzović, Radovan and Popović, Mihajlo and Milutinović, Milan and Mladenović, Goran",
year = "2010",
abstract = "Tehničko rešenje pripada oblasti novih metoda u domenu proizvodnih tehnologija.",
publisher = "Univerzitet u Beogradu - Mašinski fakultet",
journal = "Univerzitet u Beogradu - Mašinski fakultet",
title = "Nova metoda projektovanja i tehnologije izrade profilnih prizmatičnih – tangencijalnih strugarskih noževa",
url = "https://hdl.handle.net/21.15107/rcub_machinery_6950"
}

Tanović, L., Bojanić, P., Puzović, R., Popović, M., Milutinović, M.,& Mladenović, G.. (2010). Nova metoda projektovanja i tehnologije izrade profilnih prizmatičnih – tangencijalnih strugarskih noževa. in Univerzitet u Beogradu - Mašinski fakultet
Univerzitet u Beogradu - Mašinski fakultet..
https://hdl.handle.net/21.15107/rcub_machinery_6950

Tanović L, Bojanić P, Puzović R, Popović M, Milutinović M, Mladenović G. Nova metoda projektovanja i tehnologije izrade profilnih prizmatičnih – tangencijalnih strugarskih noževa. in Univerzitet u Beogradu - Mašinski fakultet. 2010;.
https://hdl.handle.net/21.15107/rcub_machinery_6950 .

Tanović, Ljubodrag, Bojanić, Pavao, Puzović, Radovan, Popović, Mihajlo, Milutinović, Milan, Mladenović, Goran, "Nova metoda projektovanja i tehnologije izrade profilnih prizmatičnih – tangencijalnih strugarskih noževa" in Univerzitet u Beogradu - Mašinski fakultet (2010),
https://hdl.handle.net/21.15107/rcub_machinery_6950 .

TY  - CONF
AU  - Bojanić, Pavao
AU  - Mladenović, Goran
PY  - 2010
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/6948
AB  - Kod obrade radnih predmeta sa skulptorskim površinama na 3-osnim CNC mašinama alatkama, putanja alata je  ključni  element za  kvalitet obrađene  površine  za vreme obrade.  U radu se  daje postupak generisanja putanje alata pri obradi skulptorskih površina za glodalo sa loptastim završetkom za slucaj izo-hrapavosti. Generisanje putanje alata se vrši u fonkciji zadate visine ruba koji ostaje između dve susedne putanje alata. Ti rubovi definišu hrapavost obradene površine.
PB  - Univerzitet u Beogradu - Mašinski fakultet
C3  - 36. JUPITER konferencija, 23 simpozijum CAD/CAM
T1  - Generisanje putanje alata po kriterijumu izo-hrapavosti pri obradi skulptorskih površina na 3-osnim cnc mašinama
EP  - 2.28
SP  - 2.22
UR  - https://hdl.handle.net/21.15107/rcub_machinery_6948
ER  - 

@conference{
author = "Bojanić, Pavao and Mladenović, Goran",
year = "2010",
abstract = "Kod obrade radnih predmeta sa skulptorskim površinama na 3-osnim CNC mašinama alatkama, putanja alata je  ključni  element za  kvalitet obrađene  površine  za vreme obrade.  U radu se  daje postupak generisanja putanje alata pri obradi skulptorskih površina za glodalo sa loptastim završetkom za slucaj izo-hrapavosti. Generisanje putanje alata se vrši u fonkciji zadate visine ruba koji ostaje između dve susedne putanje alata. Ti rubovi definišu hrapavost obradene površine.",
publisher = "Univerzitet u Beogradu - Mašinski fakultet",
journal = "36. JUPITER konferencija, 23 simpozijum CAD/CAM",
title = "Generisanje putanje alata po kriterijumu izo-hrapavosti pri obradi skulptorskih površina na 3-osnim cnc mašinama",
pages = "2.28-2.22",
url = "https://hdl.handle.net/21.15107/rcub_machinery_6948"
}

Bojanić, P.,& Mladenović, G.. (2010). Generisanje putanje alata po kriterijumu izo-hrapavosti pri obradi skulptorskih površina na 3-osnim cnc mašinama. in 36. JUPITER konferencija, 23 simpozijum CAD/CAM
Univerzitet u Beogradu - Mašinski fakultet., 2.22-2.28.
https://hdl.handle.net/21.15107/rcub_machinery_6948

Bojanić P, Mladenović G. Generisanje putanje alata po kriterijumu izo-hrapavosti pri obradi skulptorskih površina na 3-osnim cnc mašinama. in 36. JUPITER konferencija, 23 simpozijum CAD/CAM. 2010;:2.22-2.28.
https://hdl.handle.net/21.15107/rcub_machinery_6948 .

Bojanić, Pavao, Mladenović, Goran, "Generisanje putanje alata po kriterijumu izo-hrapavosti pri obradi skulptorskih površina na 3-osnim cnc mašinama" in 36. JUPITER konferencija, 23 simpozijum CAD/CAM (2010):2.22-2.28,
https://hdl.handle.net/21.15107/rcub_machinery_6948 .

TY  - CONF
AU  - Tanović, Ljubodrag
AU  - Bojanić, Pavao
AU  - Milutinović, Dragan
AU  - Glavonjić, Miloš
AU  - Puzović, Radovan
AU  - Kokotović, Branko
AU  - Živanović, Saša
AU  - Popović, Mihajlo
AU  - Slavković, Nikola
AU  - Mladenović, Goran
PY  - 2009
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/4803
AB  - У paдy ce дaje пpикaз peзyлтaтa иcтpaживaњa cпpoвeдeниx y тoкy пpвe иcтpaживaчкe гoдинe нa пpojeктy МА14034 кojи peaлизyjy пpojeктни тим фopмиpaн нa Кaтeдpи зa пpoизвoднo машинство Машинског факултета Универзитета у Београду. Пopeд пpeглeдa тeopeтcкиx и методолошких caдpжaja, пoceбнa пaжњa ce пocвeћyje пpaктичним излaзимa ocтвapeним y oквиpy oвoг пpojeктa гдe ce пpeдвиђa и peaлизaциja пилoт Мултифункциoнaлнoг реконфигурабилног oбpaднoг cиcтeмa нa бaзи poбoтa зa вишеосну oбpaдy cлoжeниx aлaтa и дeлoвa вeликиx гaбapитa oд мeкшиx мaтepиjaлa нижe и cpeдњe клace тaчнocти, ca jeднe cтpaнe, oднocнo изpaдa peзниx aлaтa cлoжeниx пoвpшинa oд caвpeмeниx aлaтниx мaтepиjaлa нa бaзи пoceбниx copти твpдoг мeтaлa и cпeциjaлниx чeликa, ca дpyгe cтpaнe.
PB  - Универзитет у Београду, Машински факултет, Катедра за производно машинство
C3  - Зборник радова - 35. ЈУПИТЕР конферененција, 31. симпозијум НУ-Роботи-ФТС
T1  - Развој технологија вишеосне обраде сложених алата за потребе домаће индустрије – Рекапитулација резултата на пројекту МА14034
EP  - 3.52
SP  - 3.39
UR  - https://hdl.handle.net/21.15107/rcub_machinery_4803
ER  - 

@conference{
author = "Tanović, Ljubodrag and Bojanić, Pavao and Milutinović, Dragan and Glavonjić, Miloš and Puzović, Radovan and Kokotović, Branko and Živanović, Saša and Popović, Mihajlo and Slavković, Nikola and Mladenović, Goran",
year = "2009",
abstract = "У paдy ce дaje пpикaз peзyлтaтa иcтpaживaњa cпpoвeдeниx y тoкy пpвe иcтpaживaчкe гoдинe нa пpojeктy МА14034 кojи peaлизyjy пpojeктни тим фopмиpaн нa Кaтeдpи зa пpoизвoднo машинство Машинског факултета Универзитета у Београду. Пopeд пpeглeдa тeopeтcкиx и методолошких caдpжaja, пoceбнa пaжњa ce пocвeћyje пpaктичним излaзимa ocтвapeним y oквиpy oвoг пpojeктa гдe ce пpeдвиђa и peaлизaциja пилoт Мултифункциoнaлнoг реконфигурабилног oбpaднoг cиcтeмa нa бaзи poбoтa зa вишеосну oбpaдy cлoжeниx aлaтa и дeлoвa вeликиx гaбapитa oд мeкшиx мaтepиjaлa нижe и cpeдњe клace тaчнocти, ca jeднe cтpaнe, oднocнo изpaдa peзниx aлaтa cлoжeниx пoвpшинa oд caвpeмeниx aлaтниx мaтepиjaлa нa бaзи пoceбниx copти твpдoг мeтaлa и cпeциjaлниx чeликa, ca дpyгe cтpaнe.",
publisher = "Универзитет у Београду, Машински факултет, Катедра за производно машинство",
journal = "Зборник радова - 35. ЈУПИТЕР конферененција, 31. симпозијум НУ-Роботи-ФТС",
title = "Развој технологија вишеосне обраде сложених алата за потребе домаће индустрије – Рекапитулација резултата на пројекту МА14034",
pages = "3.52-3.39",
url = "https://hdl.handle.net/21.15107/rcub_machinery_4803"
}

Tanović, L., Bojanić, P., Milutinović, D., Glavonjić, M., Puzović, R., Kokotović, B., Živanović, S., Popović, M., Slavković, N.,& Mladenović, G.. (2009). Развој технологија вишеосне обраде сложених алата за потребе домаће индустрије – Рекапитулација резултата на пројекту МА14034. in Зборник радова - 35. ЈУПИТЕР конферененција, 31. симпозијум НУ-Роботи-ФТС
Универзитет у Београду, Машински факултет, Катедра за производно машинство., 3.39-3.52.
https://hdl.handle.net/21.15107/rcub_machinery_4803

Tanović L, Bojanić P, Milutinović D, Glavonjić M, Puzović R, Kokotović B, Živanović S, Popović M, Slavković N, Mladenović G. Развој технологија вишеосне обраде сложених алата за потребе домаће индустрије – Рекапитулација резултата на пројекту МА14034. in Зборник радова - 35. ЈУПИТЕР конферененција, 31. симпозијум НУ-Роботи-ФТС. 2009;:3.39-3.52.
https://hdl.handle.net/21.15107/rcub_machinery_4803 .

Tanović, Ljubodrag, Bojanić, Pavao, Milutinović, Dragan, Glavonjić, Miloš, Puzović, Radovan, Kokotović, Branko, Živanović, Saša, Popović, Mihajlo, Slavković, Nikola, Mladenović, Goran, "Развој технологија вишеосне обраде сложених алата за потребе домаће индустрије – Рекапитулација резултата на пројекту МА14034" in Зборник радова - 35. ЈУПИТЕР конферененција, 31. симпозијум НУ-Роботи-ФТС (2009):3.39-3.52,
https://hdl.handle.net/21.15107/rcub_machinery_4803 .

TY  - JOUR
AU  - Tanović, Ljubodrag
AU  - Bojanić, Pavao
AU  - Puzović, Radovan
AU  - Klimenko, Sergey
PY  - 2009
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/970
AB  - This paper offers an experimental study of the microcutting mechanisms in marble grinding to aid the optimization of the marble grinding process. The necessity for investigating these mechanisms is dictated by the increased use of marble in many applications and the fact that grinding and polishing processes are the dominant technologies used to meet surface finish requirements in this natural material. The experiments are aimed at the determination of the normal component of the cutting force and of the grain traces in microcutting with a single diamond grain. The investigations carried out make provisions for establishing critical grain penetration and cutting depths and allow the prediction of the normal cutting force component as a function of grain penetration speed and depth.
PB  - ASME, New York
T2  - Journal of Manufacturing Science and Engineering-Transactions of The Asme
T1  - Experimental Investigation of Microcutting Mechanisms in Marble Grinding
IS  - 6
VL  - 131
DO  - 10.1115/1.4000619
ER  - 

@article{
author = "Tanović, Ljubodrag and Bojanić, Pavao and Puzović, Radovan and Klimenko, Sergey",
year = "2009",
abstract = "This paper offers an experimental study of the microcutting mechanisms in marble grinding to aid the optimization of the marble grinding process. The necessity for investigating these mechanisms is dictated by the increased use of marble in many applications and the fact that grinding and polishing processes are the dominant technologies used to meet surface finish requirements in this natural material. The experiments are aimed at the determination of the normal component of the cutting force and of the grain traces in microcutting with a single diamond grain. The investigations carried out make provisions for establishing critical grain penetration and cutting depths and allow the prediction of the normal cutting force component as a function of grain penetration speed and depth.",
publisher = "ASME, New York",
journal = "Journal of Manufacturing Science and Engineering-Transactions of The Asme",
title = "Experimental Investigation of Microcutting Mechanisms in Marble Grinding",
number = "6",
volume = "131",
doi = "10.1115/1.4000619"
}

Tanović, L., Bojanić, P., Puzović, R.,& Klimenko, S.. (2009). Experimental Investigation of Microcutting Mechanisms in Marble Grinding. in Journal of Manufacturing Science and Engineering-Transactions of The Asme
ASME, New York., 131(6).
https://doi.org/10.1115/1.4000619

Tanović L, Bojanić P, Puzović R, Klimenko S. Experimental Investigation of Microcutting Mechanisms in Marble Grinding. in Journal of Manufacturing Science and Engineering-Transactions of The Asme. 2009;131(6).
doi:10.1115/1.4000619 .

Tanović, Ljubodrag, Bojanić, Pavao, Puzović, Radovan, Klimenko, Sergey, "Experimental Investigation of Microcutting Mechanisms in Marble Grinding" in Journal of Manufacturing Science and Engineering-Transactions of The Asme, 131, no. 6 (2009),
https://doi.org/10.1115/1.4000619 . .