TY  - CONF
AU  - Lazić, Vukić
AU  - Nikolić, R.
AU  - Arsić, D.
AU  - Arsić, M.
AU  - Popović, Olivera
AU  - Prokić-Cvetković, Radica
AU  - Hadzima, B.
PY  - 2021
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/3631
AB  - The problem considered in this paper is the welding technology of the steel assembly of a firefighter truck rear bridge semi-housing. Since in this procedure the welding is done of the two dissimilar steels, it is necessary to analyze effects of welding on mechanical properties and microstructure of individual joint's zones. The weldability of the base metal was considered first (semi-housing tube and flange), then the welding method and the filler metal were selected and, finally, the technological parameters of welding were calculated. The computational and experimental methods were used for the base metal weldability estimate, based on the hardness measurements in the joint's critical zones and analysis of their structures. Experimental investigations performed were aimed for verification and/or eventual correction of the proposed welding technology.
PB  - Elsevier B.V.
C3  - Transportation Research Procedia
T1  - Analysis of welding of the rear bridge semi-housing assembly of a firefighter truck by the semi-automatic procedure in gas protection
EP  - 552
SP  - 544
VL  - 55
DO  - 10.1016/j.trpro.2021.07.020
ER  - 

@conference{
author = "Lazić, Vukić and Nikolić, R. and Arsić, D. and Arsić, M. and Popović, Olivera and Prokić-Cvetković, Radica and Hadzima, B.",
year = "2021",
abstract = "The problem considered in this paper is the welding technology of the steel assembly of a firefighter truck rear bridge semi-housing. Since in this procedure the welding is done of the two dissimilar steels, it is necessary to analyze effects of welding on mechanical properties and microstructure of individual joint's zones. The weldability of the base metal was considered first (semi-housing tube and flange), then the welding method and the filler metal were selected and, finally, the technological parameters of welding were calculated. The computational and experimental methods were used for the base metal weldability estimate, based on the hardness measurements in the joint's critical zones and analysis of their structures. Experimental investigations performed were aimed for verification and/or eventual correction of the proposed welding technology.",
publisher = "Elsevier B.V.",
journal = "Transportation Research Procedia",
title = "Analysis of welding of the rear bridge semi-housing assembly of a firefighter truck by the semi-automatic procedure in gas protection",
pages = "552-544",
volume = "55",
doi = "10.1016/j.trpro.2021.07.020"
}

Lazić, V., Nikolić, R., Arsić, D., Arsić, M., Popović, O., Prokić-Cvetković, R.,& Hadzima, B.. (2021). Analysis of welding of the rear bridge semi-housing assembly of a firefighter truck by the semi-automatic procedure in gas protection. in Transportation Research Procedia
Elsevier B.V.., 55, 544-552.
https://doi.org/10.1016/j.trpro.2021.07.020

Lazić V, Nikolić R, Arsić D, Arsić M, Popović O, Prokić-Cvetković R, Hadzima B. Analysis of welding of the rear bridge semi-housing assembly of a firefighter truck by the semi-automatic procedure in gas protection. in Transportation Research Procedia. 2021;55:544-552.
doi:10.1016/j.trpro.2021.07.020 .

Lazić, Vukić, Nikolić, R., Arsić, D., Arsić, M., Popović, Olivera, Prokić-Cvetković, Radica, Hadzima, B., "Analysis of welding of the rear bridge semi-housing assembly of a firefighter truck by the semi-automatic procedure in gas protection" in Transportation Research Procedia, 55 (2021):544-552,
https://doi.org/10.1016/j.trpro.2021.07.020 . .

TY  - JOUR
AU  - Milošević, Nenad
AU  - Sedmak, Aleksandar
AU  - Bakić, Gordana
AU  - Lazić, Vukić
AU  - Milošević, Miloš
AU  - Mladenović, Goran
AU  - Maslarević, Aleksandar
PY  - 2021
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/3485
AB  - This paper presents new methodology for determining the actual stress-strain diagram based on analytical equations, in combination with numerical and experimental data. The first step was to use the 3D digital image correlation (DIC) to estimate true stress-strain diagram by replacing common analytical expression for contraction with measured values. Next step was to estimate the stress concentration by using a new methodology, based on recently introduced analytical expressions and numerical verification by the finite element method (FEM), to obtain actual stress-strain diagrams, as named in this paper. The essence of new methodology is to introduce stress concentration factor into the procedure of actual stress evaluation. New methodology is then applied to determine actual stress-strain diagrams for two undermatched welded joints with different rectangular cross-section and groove shapes, made of martensitic steels X10 CrMoVNb 9-1 and Armox 500T. Results indicated that new methodology is a general one, since it is not dependent on welded joint material and geometry.
PB  - MDPI, Basel
T2  - Materials
T1  - Determination of the Actual Stress-Strain Diagram for Undermatching Welded Joint Using DIC and FEM
IS  - 16
VL  - 14
DO  - 10.3390/ma14164691
ER  - 

@article{
author = "Milošević, Nenad and Sedmak, Aleksandar and Bakić, Gordana and Lazić, Vukić and Milošević, Miloš and Mladenović, Goran and Maslarević, Aleksandar",
year = "2021",
abstract = "This paper presents new methodology for determining the actual stress-strain diagram based on analytical equations, in combination with numerical and experimental data. The first step was to use the 3D digital image correlation (DIC) to estimate true stress-strain diagram by replacing common analytical expression for contraction with measured values. Next step was to estimate the stress concentration by using a new methodology, based on recently introduced analytical expressions and numerical verification by the finite element method (FEM), to obtain actual stress-strain diagrams, as named in this paper. The essence of new methodology is to introduce stress concentration factor into the procedure of actual stress evaluation. New methodology is then applied to determine actual stress-strain diagrams for two undermatched welded joints with different rectangular cross-section and groove shapes, made of martensitic steels X10 CrMoVNb 9-1 and Armox 500T. Results indicated that new methodology is a general one, since it is not dependent on welded joint material and geometry.",
publisher = "MDPI, Basel",
journal = "Materials",
title = "Determination of the Actual Stress-Strain Diagram for Undermatching Welded Joint Using DIC and FEM",
number = "16",
volume = "14",
doi = "10.3390/ma14164691"
}

Milošević, N., Sedmak, A., Bakić, G., Lazić, V., Milošević, M., Mladenović, G.,& Maslarević, A.. (2021). Determination of the Actual Stress-Strain Diagram for Undermatching Welded Joint Using DIC and FEM. in Materials
MDPI, Basel., 14(16).
https://doi.org/10.3390/ma14164691

Milošević N, Sedmak A, Bakić G, Lazić V, Milošević M, Mladenović G, Maslarević A. Determination of the Actual Stress-Strain Diagram for Undermatching Welded Joint Using DIC and FEM. in Materials. 2021;14(16).
doi:10.3390/ma14164691 .

Milošević, Nenad, Sedmak, Aleksandar, Bakić, Gordana, Lazić, Vukić, Milošević, Miloš, Mladenović, Goran, Maslarević, Aleksandar, "Determination of the Actual Stress-Strain Diagram for Undermatching Welded Joint Using DIC and FEM" in Materials, 14, no. 16 (2021),
https://doi.org/10.3390/ma14164691 . .

TY  - JOUR
AU  - Arsić, Dušan
AU  - Lazić, Vukić
AU  - Sedmak, Aleksandar
AU  - Aleksandrović, Srbislav
AU  - Zivković, Jelena
AU  - Đorđević, Milan
AU  - Mladenović, Goran
PY  - 2020
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/3390
AB  - This paper presents an experimental and numerical study into the influence of elevated temperatures on mechanical properties of the heat treated high quality hot work tool steel H11. This steel belongs to a group of alloyed steels with extraordinary mechanical properties. The aim of this study was to determine the highest temperature at which these properties are still maintained. The experimental investigation focused on the tensile testing of specimens at seven different temperatures, including the room temperature. The highest testing temperature was 700 degrees C. The heat treatment of plates (specimens) consisted of quenching and tempering. Although the strain hardening of this type of materials is small, the strain hardening curves were calculated to show if there was a possibility for the material to increase its strength due to exploitation loads. Also, a numerical analysis of the tensile test by using the finite element method was done in order to define an appropriate model for numerical testing. The obtained results are then compared with the experimental results.
PB  - Univ Zagreb Fac Mechanical Engineering & Naval Architecture, Zagreb
T2  - Transactions of Famena
T1  - Effect of elevated temperatures on mechanical properties of ultra high strength hot work tool steel h11
EP  - 82
IS  - 2
SP  - 71
VL  - 44
DO  - 10.21278/TOF.44207
ER  - 

@article{
author = "Arsić, Dušan and Lazić, Vukić and Sedmak, Aleksandar and Aleksandrović, Srbislav and Zivković, Jelena and Đorđević, Milan and Mladenović, Goran",
year = "2020",
abstract = "This paper presents an experimental and numerical study into the influence of elevated temperatures on mechanical properties of the heat treated high quality hot work tool steel H11. This steel belongs to a group of alloyed steels with extraordinary mechanical properties. The aim of this study was to determine the highest temperature at which these properties are still maintained. The experimental investigation focused on the tensile testing of specimens at seven different temperatures, including the room temperature. The highest testing temperature was 700 degrees C. The heat treatment of plates (specimens) consisted of quenching and tempering. Although the strain hardening of this type of materials is small, the strain hardening curves were calculated to show if there was a possibility for the material to increase its strength due to exploitation loads. Also, a numerical analysis of the tensile test by using the finite element method was done in order to define an appropriate model for numerical testing. The obtained results are then compared with the experimental results.",
publisher = "Univ Zagreb Fac Mechanical Engineering & Naval Architecture, Zagreb",
journal = "Transactions of Famena",
title = "Effect of elevated temperatures on mechanical properties of ultra high strength hot work tool steel h11",
pages = "82-71",
number = "2",
volume = "44",
doi = "10.21278/TOF.44207"
}

Arsić, D., Lazić, V., Sedmak, A., Aleksandrović, S., Zivković, J., Đorđević, M.,& Mladenović, G.. (2020). Effect of elevated temperatures on mechanical properties of ultra high strength hot work tool steel h11. in Transactions of Famena
Univ Zagreb Fac Mechanical Engineering & Naval Architecture, Zagreb., 44(2), 71-82.
https://doi.org/10.21278/TOF.44207

Arsić D, Lazić V, Sedmak A, Aleksandrović S, Zivković J, Đorđević M, Mladenović G. Effect of elevated temperatures on mechanical properties of ultra high strength hot work tool steel h11. in Transactions of Famena. 2020;44(2):71-82.
doi:10.21278/TOF.44207 .

Arsić, Dušan, Lazić, Vukić, Sedmak, Aleksandar, Aleksandrović, Srbislav, Zivković, Jelena, Đorđević, Milan, Mladenović, Goran, "Effect of elevated temperatures on mechanical properties of ultra high strength hot work tool steel h11" in Transactions of Famena, 44, no. 2 (2020):71-82,
https://doi.org/10.21278/TOF.44207 . .

TY  - JOUR
AU  - Sedmak, Aleksandar
AU  - Arsić, M.
AU  - Šarkoćević, Živče
AU  - Međo, Bojan
AU  - Rakin, Marko
AU  - Arsić, D.
AU  - Lazić, Vukić
PY  - 2020
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/3349
AB  - Experimental investigation of the integrity of casing pipes, used in the oil drilling rigs, withdrawn after about 70,000 h of service, has been conducted, together with numerical simulation. Pipes were manufactured by the high frequency contact welding (HF) of API J55 steel. The influence of corrosion damage is investigated by means of pressure test of a pipe with different damage levels made by machining the circular holes. The finite element analysis of the damaged pipe subjected to internal pressure is conducted to simulate the stress state in the pipe and to establish the criteria for the maximum pressure that a damaged pipe can withstand. Several analytical expressions were used to estimate the maximum pressure in a damaged pipeline, and the solutions were compared to predictions of finite element models and experimental results.
PB  - Elsevier Sci Ltd, Oxford
T2  - International Journal of Pressure Vessels and Piping
T1  - Remaining strength of API J55 steel casing pipes damaged by corrosion
VL  - 188
DO  - 10.1016/j.ijpvp.2020.104230
ER  - 

@article{
author = "Sedmak, Aleksandar and Arsić, M. and Šarkoćević, Živče and Međo, Bojan and Rakin, Marko and Arsić, D. and Lazić, Vukić",
year = "2020",
abstract = "Experimental investigation of the integrity of casing pipes, used in the oil drilling rigs, withdrawn after about 70,000 h of service, has been conducted, together with numerical simulation. Pipes were manufactured by the high frequency contact welding (HF) of API J55 steel. The influence of corrosion damage is investigated by means of pressure test of a pipe with different damage levels made by machining the circular holes. The finite element analysis of the damaged pipe subjected to internal pressure is conducted to simulate the stress state in the pipe and to establish the criteria for the maximum pressure that a damaged pipe can withstand. Several analytical expressions were used to estimate the maximum pressure in a damaged pipeline, and the solutions were compared to predictions of finite element models and experimental results.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "International Journal of Pressure Vessels and Piping",
title = "Remaining strength of API J55 steel casing pipes damaged by corrosion",
volume = "188",
doi = "10.1016/j.ijpvp.2020.104230"
}

Sedmak, A., Arsić, M., Šarkoćević, Ž., Međo, B., Rakin, M., Arsić, D.,& Lazić, V.. (2020). Remaining strength of API J55 steel casing pipes damaged by corrosion. in International Journal of Pressure Vessels and Piping
Elsevier Sci Ltd, Oxford., 188.
https://doi.org/10.1016/j.ijpvp.2020.104230

Sedmak A, Arsić M, Šarkoćević Ž, Međo B, Rakin M, Arsić D, Lazić V. Remaining strength of API J55 steel casing pipes damaged by corrosion. in International Journal of Pressure Vessels and Piping. 2020;188.
doi:10.1016/j.ijpvp.2020.104230 .

Sedmak, Aleksandar, Arsić, M., Šarkoćević, Živče, Međo, Bojan, Rakin, Marko, Arsić, D., Lazić, Vukić, "Remaining strength of API J55 steel casing pipes damaged by corrosion" in International Journal of Pressure Vessels and Piping, 188 (2020),
https://doi.org/10.1016/j.ijpvp.2020.104230 . .

TY  - JOUR
AU  - Đorđević, Milan
AU  - Aleksandrović, Srbislav
AU  - Djacić, Slavisa
AU  - Sedmak, Aleksandar
AU  - Lazić, Vukić
AU  - Arsić, Dušan
AU  - Mutavdzić, Milan
PY  - 2019
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/2999
AB  - Influence of the contact pressure in the deep drawing processes is a very actual research topic in the metal forming technology. Within this research the tribological model of the strip sliding in the flat die was developed. The original experimental computerized apparatus for testing of the strip sliding in the variable contact pressure conditions was developed, as well. The complex, multi-factor experiment was performed by application of the Al thin sheet, with the contact elements of various roughnesses, with different lubricants application and with the variable contact pressure. Besides the description of the developed apparatus, the theoretical way for determination of the pressure dependences was also presented. Based on the theoretical changes of pressure, set in advance, the real influence of the contact pressure was obtained, for each of the given conditions. That makes possible to determine the influence of the tribological factors on the actual pressure. The obtained real contact pressure has verified the reliability of the experimental apparatus, namely the degree of the theoretical pressure dependences deviation from the real ones.
PB  - Univ Osijek, Tech Fac, Slavonski Brod
T2  - Tehnički vjesnik
T1  - Simulation of Flat Die Deep Drawing Process by Variable Contact Pressure Sliding Model
EP  - 1204
IS  - 5
SP  - 1199
VL  - 26
DO  - 10.17559/TV-20161215205553
ER  - 

@article{
author = "Đorđević, Milan and Aleksandrović, Srbislav and Djacić, Slavisa and Sedmak, Aleksandar and Lazić, Vukić and Arsić, Dušan and Mutavdzić, Milan",
year = "2019",
abstract = "Influence of the contact pressure in the deep drawing processes is a very actual research topic in the metal forming technology. Within this research the tribological model of the strip sliding in the flat die was developed. The original experimental computerized apparatus for testing of the strip sliding in the variable contact pressure conditions was developed, as well. The complex, multi-factor experiment was performed by application of the Al thin sheet, with the contact elements of various roughnesses, with different lubricants application and with the variable contact pressure. Besides the description of the developed apparatus, the theoretical way for determination of the pressure dependences was also presented. Based on the theoretical changes of pressure, set in advance, the real influence of the contact pressure was obtained, for each of the given conditions. That makes possible to determine the influence of the tribological factors on the actual pressure. The obtained real contact pressure has verified the reliability of the experimental apparatus, namely the degree of the theoretical pressure dependences deviation from the real ones.",
publisher = "Univ Osijek, Tech Fac, Slavonski Brod",
journal = "Tehnički vjesnik",
title = "Simulation of Flat Die Deep Drawing Process by Variable Contact Pressure Sliding Model",
pages = "1204-1199",
number = "5",
volume = "26",
doi = "10.17559/TV-20161215205553"
}

Đorđević, M., Aleksandrović, S., Djacić, S., Sedmak, A., Lazić, V., Arsić, D.,& Mutavdzić, M.. (2019). Simulation of Flat Die Deep Drawing Process by Variable Contact Pressure Sliding Model. in Tehnički vjesnik
Univ Osijek, Tech Fac, Slavonski Brod., 26(5), 1199-1204.
https://doi.org/10.17559/TV-20161215205553

Đorđević M, Aleksandrović S, Djacić S, Sedmak A, Lazić V, Arsić D, Mutavdzić M. Simulation of Flat Die Deep Drawing Process by Variable Contact Pressure Sliding Model. in Tehnički vjesnik. 2019;26(5):1199-1204.
doi:10.17559/TV-20161215205553 .

Đorđević, Milan, Aleksandrović, Srbislav, Djacić, Slavisa, Sedmak, Aleksandar, Lazić, Vukić, Arsić, Dušan, Mutavdzić, Milan, "Simulation of Flat Die Deep Drawing Process by Variable Contact Pressure Sliding Model" in Tehnički vjesnik, 26, no. 5 (2019):1199-1204,
https://doi.org/10.17559/TV-20161215205553 . .

TY  - JOUR
AU  - Ratković, Nada
AU  - Lazić, Vukić
AU  - Arsić, Dušan
AU  - Nikolić, Ružica R.
AU  - Prokić-Cvetković, Radica
AU  - Popović, Olivera
PY  - 2018
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/2840
AB  - Purpose - The purpose of this paper is to point out the possibilities for friction welding of dissimilar steels which are used in various industries. In addition, friction welding is a welding method that is applied for executing the very responsible joints. This research is focused on friction and tribological processes in the friction plane of the two pieces during the welding. Design/methodology/approach - The present study research has been conducted based on the experimental testing of cylindrical specimens and results are analyzed. Findings - The austenite grain size is affected by several factors through the friction process phase and the compacting phase during the welding. The very fine grain is the consequence of the high degree of the plastic deformation of the near-the-contact layers even in the friction phase. The viscous layer, which is formed during the stable friction phase, is the area where the moving of matter occurs according to a very complex mechanism. Originality/value - The paper contains useful results from the area of conventional friction welding of dissimilar steels and it can be very useful to researchers and engineers who deal with similar problems.
PB  - Emerald Group Publishing Ltd, Bingley
T2  - Industrial Lubrication and Tribology
T1  - Microstructure in the joining zone during the friction welding of the two dissimilar steels
EP  - 407
IS  - 2
SP  - 401
VL  - 70
DO  - 10.1108/ILT-08-2017-0234
ER  - 

@article{
author = "Ratković, Nada and Lazić, Vukić and Arsić, Dušan and Nikolić, Ružica R. and Prokić-Cvetković, Radica and Popović, Olivera",
year = "2018",
abstract = "Purpose - The purpose of this paper is to point out the possibilities for friction welding of dissimilar steels which are used in various industries. In addition, friction welding is a welding method that is applied for executing the very responsible joints. This research is focused on friction and tribological processes in the friction plane of the two pieces during the welding. Design/methodology/approach - The present study research has been conducted based on the experimental testing of cylindrical specimens and results are analyzed. Findings - The austenite grain size is affected by several factors through the friction process phase and the compacting phase during the welding. The very fine grain is the consequence of the high degree of the plastic deformation of the near-the-contact layers even in the friction phase. The viscous layer, which is formed during the stable friction phase, is the area where the moving of matter occurs according to a very complex mechanism. Originality/value - The paper contains useful results from the area of conventional friction welding of dissimilar steels and it can be very useful to researchers and engineers who deal with similar problems.",
publisher = "Emerald Group Publishing Ltd, Bingley",
journal = "Industrial Lubrication and Tribology",
title = "Microstructure in the joining zone during the friction welding of the two dissimilar steels",
pages = "407-401",
number = "2",
volume = "70",
doi = "10.1108/ILT-08-2017-0234"
}

Ratković, N., Lazić, V., Arsić, D., Nikolić, R. R., Prokić-Cvetković, R.,& Popović, O.. (2018). Microstructure in the joining zone during the friction welding of the two dissimilar steels. in Industrial Lubrication and Tribology
Emerald Group Publishing Ltd, Bingley., 70(2), 401-407.
https://doi.org/10.1108/ILT-08-2017-0234

Ratković N, Lazić V, Arsić D, Nikolić RR, Prokić-Cvetković R, Popović O. Microstructure in the joining zone during the friction welding of the two dissimilar steels. in Industrial Lubrication and Tribology. 2018;70(2):401-407.
doi:10.1108/ILT-08-2017-0234 .

Ratković, Nada, Lazić, Vukić, Arsić, Dušan, Nikolić, Ružica R., Prokić-Cvetković, Radica, Popović, Olivera, "Microstructure in the joining zone during the friction welding of the two dissimilar steels" in Industrial Lubrication and Tribology, 70, no. 2 (2018):401-407,
https://doi.org/10.1108/ILT-08-2017-0234 . .

TY  - JOUR
AU  - Lazić, Vukić
AU  - Arsić, D.
AU  - Nikolić, R.R.
AU  - Đorđević, D.
AU  - Prokić-Cvetković, Radica
AU  - Popović, Olivera
PY  - 2017
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/2733
AB  - The problems related to welding of the high strength steel, aimed for manufacturing of welded structures operating in the prominent wear conditions, is considered in this paper. The paper presents an analysis of possibilities and prescribing the technology for welding the high strength steel HARDOX 450. The methodology for estimate the weldability of this steel was established in the theoretical part of the paper, as well as calculations of the welding parameters, while the hardness was investigated in details and the macro and micro structures of the individual welded joint zones were estimated in the experimental part. Obtained experimental results could be usefully applied for selecting and establishing the optimal welding technology for structures made of this steel. The technology thus established and the GMAW welding regime can enable successful execution of the welded joints and reduce the possibility for appearance of flaws and cracks to a minimum.
PB  - Trans Tech Publications Ltd
T2  - Key Engineering Materials
T1  - Application of the high strength steel hardox 450 for manufacturing of assemblies in the military industry
EP  - 105
SP  - 96
VL  - 755
DO  - 10.4028/www.scientific.net/KEM.755.96
ER  - 

@article{
author = "Lazić, Vukić and Arsić, D. and Nikolić, R.R. and Đorđević, D. and Prokić-Cvetković, Radica and Popović, Olivera",
year = "2017",
abstract = "The problems related to welding of the high strength steel, aimed for manufacturing of welded structures operating in the prominent wear conditions, is considered in this paper. The paper presents an analysis of possibilities and prescribing the technology for welding the high strength steel HARDOX 450. The methodology for estimate the weldability of this steel was established in the theoretical part of the paper, as well as calculations of the welding parameters, while the hardness was investigated in details and the macro and micro structures of the individual welded joint zones were estimated in the experimental part. Obtained experimental results could be usefully applied for selecting and establishing the optimal welding technology for structures made of this steel. The technology thus established and the GMAW welding regime can enable successful execution of the welded joints and reduce the possibility for appearance of flaws and cracks to a minimum.",
publisher = "Trans Tech Publications Ltd",
journal = "Key Engineering Materials",
title = "Application of the high strength steel hardox 450 for manufacturing of assemblies in the military industry",
pages = "105-96",
volume = "755",
doi = "10.4028/www.scientific.net/KEM.755.96"
}

Lazić, V., Arsić, D., Nikolić, R.R., Đorđević, D., Prokić-Cvetković, R.,& Popović, O.. (2017). Application of the high strength steel hardox 450 for manufacturing of assemblies in the military industry. in Key Engineering Materials
Trans Tech Publications Ltd., 755, 96-105.
https://doi.org/10.4028/www.scientific.net/KEM.755.96

Lazić V, Arsić D, Nikolić R, Đorđević D, Prokić-Cvetković R, Popović O. Application of the high strength steel hardox 450 for manufacturing of assemblies in the military industry. in Key Engineering Materials. 2017;755:96-105.
doi:10.4028/www.scientific.net/KEM.755.96 .

Lazić, Vukić, Arsić, D., Nikolić, R.R., Đorđević, D., Prokić-Cvetković, Radica, Popović, Olivera, "Application of the high strength steel hardox 450 for manufacturing of assemblies in the military industry" in Key Engineering Materials, 755 (2017):96-105,
https://doi.org/10.4028/www.scientific.net/KEM.755.96 . .

TY  - JOUR
AU  - Ratković, Nada R.
AU  - Arsić, Dušan M.
AU  - Lazić, Vukić
AU  - Nikolić, Ružica R.
AU  - Hadzima, Branislav
AU  - Palcek, Peter
AU  - Sedmak, Aleksandar
PY  - 2017
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/2589
AB  - In this paper is presented a theoretical-experimental analysis of the aluminum-copper joining by friction welding. Considering that such Al-Cu bimetal joints are widely applied in industrial practice, experimental analysis in this paper was performed on the concrete elements used in electronics. The fact that the joining is done of the two dissimilar materials points to complexity of the problem, since phenomena that appear in the joint zone extremely influence physical, mechanical and structural properties of the welded/base metals. Besides the theoretical analysis of the basic phases and mechanisms of the friction welding process, the research also included experimental analysis of the geometry changes due to the plastic deformation, the change of microstructure and hardness in the joint zone, as well as of the basic mechanical properties of the Al-Cu joint, such as tensile strength. This paper presents some significant results, which point to the possibility for realization of the reliable joints of the two dissimilar metals.
PB  - Univerzitet u Beogradu - Mašinski fakultet, Beograd
T2  - FME Transactions
T1  - Influence of Friction Welding Parameters on Properties of the Al-Cu Joint
EP  - 171
IS  - 1
SP  - 165
VL  - 45
DO  - 10.5937/fmet1701165R
ER  - 

@article{
author = "Ratković, Nada R. and Arsić, Dušan M. and Lazić, Vukić and Nikolić, Ružica R. and Hadzima, Branislav and Palcek, Peter and Sedmak, Aleksandar",
year = "2017",
abstract = "In this paper is presented a theoretical-experimental analysis of the aluminum-copper joining by friction welding. Considering that such Al-Cu bimetal joints are widely applied in industrial practice, experimental analysis in this paper was performed on the concrete elements used in electronics. The fact that the joining is done of the two dissimilar materials points to complexity of the problem, since phenomena that appear in the joint zone extremely influence physical, mechanical and structural properties of the welded/base metals. Besides the theoretical analysis of the basic phases and mechanisms of the friction welding process, the research also included experimental analysis of the geometry changes due to the plastic deformation, the change of microstructure and hardness in the joint zone, as well as of the basic mechanical properties of the Al-Cu joint, such as tensile strength. This paper presents some significant results, which point to the possibility for realization of the reliable joints of the two dissimilar metals.",
publisher = "Univerzitet u Beogradu - Mašinski fakultet, Beograd",
journal = "FME Transactions",
title = "Influence of Friction Welding Parameters on Properties of the Al-Cu Joint",
pages = "171-165",
number = "1",
volume = "45",
doi = "10.5937/fmet1701165R"
}

Ratković, N. R., Arsić, D. M., Lazić, V., Nikolić, R. R., Hadzima, B., Palcek, P.,& Sedmak, A.. (2017). Influence of Friction Welding Parameters on Properties of the Al-Cu Joint. in FME Transactions
Univerzitet u Beogradu - Mašinski fakultet, Beograd., 45(1), 165-171.
https://doi.org/10.5937/fmet1701165R

Ratković NR, Arsić DM, Lazić V, Nikolić RR, Hadzima B, Palcek P, Sedmak A. Influence of Friction Welding Parameters on Properties of the Al-Cu Joint. in FME Transactions. 2017;45(1):165-171.
doi:10.5937/fmet1701165R .

Ratković, Nada R., Arsić, Dušan M., Lazić, Vukić, Nikolić, Ružica R., Hadzima, Branislav, Palcek, Peter, Sedmak, Aleksandar, "Influence of Friction Welding Parameters on Properties of the Al-Cu Joint" in FME Transactions, 45, no. 1 (2017):165-171,
https://doi.org/10.5937/fmet1701165R . .

TY  - JOUR
AU  - Arsić, D.
AU  - Đorđević, M.
AU  - Zivković, J.
AU  - Sedmak, Aleksandar
AU  - Aleksandrović, Srbislav
AU  - Lazić, Vukić
AU  - Rakić, D.
PY  - 2016
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/2494
AB  - We present the experimental-numerical analysis of the influence of temperature on mechanical properties of structural high-strength steel class S690QL. Since the steel S690QL belongs to a group of steels with good mechanical properties, the aim of this paper is to determine the highest temperatures at which these good characteristics are kept. Experimental tensile testings of the specimens were performed at five different temperatures in the range from 20 to 550A degrees C. Beside experimental testing, strengthening curves were calculated and numerical analysis using finite element method was performed. Both the experimental and numerical results have shown that decrease of mecahanical properties occurs at approximately 450A degrees C.
PB  - Springer, New York
T2  - Strength of Materials
T1  - Experimental-Numerical Study of Tensile Strength of the High-Strength Steel S690QL at Elevated Temperatures
EP  - 695
IS  - 5
SP  - 687
VL  - 48
DO  - 10.1007/s11223-016-9812-x
ER  - 

@article{
author = "Arsić, D. and Đorđević, M. and Zivković, J. and Sedmak, Aleksandar and Aleksandrović, Srbislav and Lazić, Vukić and Rakić, D.",
year = "2016",
abstract = "We present the experimental-numerical analysis of the influence of temperature on mechanical properties of structural high-strength steel class S690QL. Since the steel S690QL belongs to a group of steels with good mechanical properties, the aim of this paper is to determine the highest temperatures at which these good characteristics are kept. Experimental tensile testings of the specimens were performed at five different temperatures in the range from 20 to 550A degrees C. Beside experimental testing, strengthening curves were calculated and numerical analysis using finite element method was performed. Both the experimental and numerical results have shown that decrease of mecahanical properties occurs at approximately 450A degrees C.",
publisher = "Springer, New York",
journal = "Strength of Materials",
title = "Experimental-Numerical Study of Tensile Strength of the High-Strength Steel S690QL at Elevated Temperatures",
pages = "695-687",
number = "5",
volume = "48",
doi = "10.1007/s11223-016-9812-x"
}

Arsić, D., Đorđević, M., Zivković, J., Sedmak, A., Aleksandrović, S., Lazić, V.,& Rakić, D.. (2016). Experimental-Numerical Study of Tensile Strength of the High-Strength Steel S690QL at Elevated Temperatures. in Strength of Materials
Springer, New York., 48(5), 687-695.
https://doi.org/10.1007/s11223-016-9812-x

Arsić D, Đorđević M, Zivković J, Sedmak A, Aleksandrović S, Lazić V, Rakić D. Experimental-Numerical Study of Tensile Strength of the High-Strength Steel S690QL at Elevated Temperatures. in Strength of Materials. 2016;48(5):687-695.
doi:10.1007/s11223-016-9812-x .

Arsić, D., Đorđević, M., Zivković, J., Sedmak, Aleksandar, Aleksandrović, Srbislav, Lazić, Vukić, Rakić, D., "Experimental-Numerical Study of Tensile Strength of the High-Strength Steel S690QL at Elevated Temperatures" in Strength of Materials, 48, no. 5 (2016):687-695,
https://doi.org/10.1007/s11223-016-9812-x . .

TY  - JOUR
AU  - Lazić, Vukić
AU  - Aleksandrović, Srbislav
AU  - Arsić, D.
AU  - Sedmak, Aleksandar
AU  - Ilić, A.
AU  - Đorđević, M.
AU  - Ivanović, Lozica
PY  - 2016
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/2377
AB  - This paper presents the analysis of the influence of temperature on mechanic properties of the base material and welded joints made of high strength steel. The joints were welded on S690QL high strength steel plates using the Metal Active Gas (MAG) Welding and two filler materials of different properties. Since the steel S690QL belongs to a group of steels with high strength, the aim of this paper is to determine the temperature at which strength starts to decrease. Experimental tensile testings of the welded joints were performed at five different temperatures in the range from 20 to 550 °C.
PB  - Faculty of Metallurgy
T2  - Metalurgija
T1  - The influence of temperature on mechanical properties of the base material (BM) and welded joint (WJ) made of steel S690QL
EP  - 216
IS  - 2
SP  - 213
VL  - 55
UR  - https://hdl.handle.net/21.15107/rcub_machinery_2377
ER  - 

@article{
author = "Lazić, Vukić and Aleksandrović, Srbislav and Arsić, D. and Sedmak, Aleksandar and Ilić, A. and Đorđević, M. and Ivanović, Lozica",
year = "2016",
abstract = "This paper presents the analysis of the influence of temperature on mechanic properties of the base material and welded joints made of high strength steel. The joints were welded on S690QL high strength steel plates using the Metal Active Gas (MAG) Welding and two filler materials of different properties. Since the steel S690QL belongs to a group of steels with high strength, the aim of this paper is to determine the temperature at which strength starts to decrease. Experimental tensile testings of the welded joints were performed at five different temperatures in the range from 20 to 550 °C.",
publisher = "Faculty of Metallurgy",
journal = "Metalurgija",
title = "The influence of temperature on mechanical properties of the base material (BM) and welded joint (WJ) made of steel S690QL",
pages = "216-213",
number = "2",
volume = "55",
url = "https://hdl.handle.net/21.15107/rcub_machinery_2377"
}

Lazić, V., Aleksandrović, S., Arsić, D., Sedmak, A., Ilić, A., Đorđević, M.,& Ivanović, L.. (2016). The influence of temperature on mechanical properties of the base material (BM) and welded joint (WJ) made of steel S690QL. in Metalurgija
Faculty of Metallurgy., 55(2), 213-216.
https://hdl.handle.net/21.15107/rcub_machinery_2377

Lazić V, Aleksandrović S, Arsić D, Sedmak A, Ilić A, Đorđević M, Ivanović L. The influence of temperature on mechanical properties of the base material (BM) and welded joint (WJ) made of steel S690QL. in Metalurgija. 2016;55(2):213-216.
https://hdl.handle.net/21.15107/rcub_machinery_2377 .

Lazić, Vukić, Aleksandrović, Srbislav, Arsić, D., Sedmak, Aleksandar, Ilić, A., Đorđević, M., Ivanović, Lozica, "The influence of temperature on mechanical properties of the base material (BM) and welded joint (WJ) made of steel S690QL" in Metalurgija, 55, no. 2 (2016):213-216,
https://hdl.handle.net/21.15107/rcub_machinery_2377 .

TY  - JOUR
AU  - Lazić, Vukić
AU  - Sedmak, Aleksandar
AU  - Samardžić, I.
AU  - Aleksandrović, Srbislav
AU  - Milosavljević, Dragan I.
AU  - Arsić, D.
AU  - Đorđević, M.
PY  - 2016
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/2313
AB  - This paper points out complex working conditions of forging dies, which are the most frequent causes of their damage, and proposes suitable hard-facing repair procedures. The shear strength between the hard-faced layer and base metal has been measured using specially developed tool, and correlation between output results and the applied hard-facing technology is established.
PB  - Faculty of Metallurgy
T2  - Metalurgija
T1  - Determination of bond strength between the hard-faced (HF) layer and the base material (BM) of forging dies
EP  - 94
IS  - 1
SP  - 91
VL  - 55
UR  - https://hdl.handle.net/21.15107/rcub_machinery_2313
ER  - 

@article{
author = "Lazić, Vukić and Sedmak, Aleksandar and Samardžić, I. and Aleksandrović, Srbislav and Milosavljević, Dragan I. and Arsić, D. and Đorđević, M.",
year = "2016",
abstract = "This paper points out complex working conditions of forging dies, which are the most frequent causes of their damage, and proposes suitable hard-facing repair procedures. The shear strength between the hard-faced layer and base metal has been measured using specially developed tool, and correlation between output results and the applied hard-facing technology is established.",
publisher = "Faculty of Metallurgy",
journal = "Metalurgija",
title = "Determination of bond strength between the hard-faced (HF) layer and the base material (BM) of forging dies",
pages = "94-91",
number = "1",
volume = "55",
url = "https://hdl.handle.net/21.15107/rcub_machinery_2313"
}

Lazić, V., Sedmak, A., Samardžić, I., Aleksandrović, S., Milosavljević, D. I., Arsić, D.,& Đorđević, M.. (2016). Determination of bond strength between the hard-faced (HF) layer and the base material (BM) of forging dies. in Metalurgija
Faculty of Metallurgy., 55(1), 91-94.
https://hdl.handle.net/21.15107/rcub_machinery_2313

Lazić V, Sedmak A, Samardžić I, Aleksandrović S, Milosavljević DI, Arsić D, Đorđević M. Determination of bond strength between the hard-faced (HF) layer and the base material (BM) of forging dies. in Metalurgija. 2016;55(1):91-94.
https://hdl.handle.net/21.15107/rcub_machinery_2313 .

Lazić, Vukić, Sedmak, Aleksandar, Samardžić, I., Aleksandrović, Srbislav, Milosavljević, Dragan I., Arsić, D., Đorđević, M., "Determination of bond strength between the hard-faced (HF) layer and the base material (BM) of forging dies" in Metalurgija, 55, no. 1 (2016):91-94,
https://hdl.handle.net/21.15107/rcub_machinery_2313 .

TY  - JOUR
AU  - Arsić, D.
AU  - Lazić, Vukić
AU  - Sedmak, Aleksandar
AU  - Nikolić, Ružica R.
AU  - Aleksandrović, Srbislav
AU  - Đorđević, M.
AU  - Bakić, Ramo
PY  - 2016
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/2312
AB  - In exploitation, the forging dies are exposed to heating up to very high temperatures, variable loads: compressive, impact and shear. In this paper, the reparatory hard facing of the damaged forging dies is considered. The objective was to establish the optimal reparatory technology based on cooling time t8/5. The verification of the adopted technology was done by investigation of the hard faced layers microstructure and measurements of hardness within the welded layers’ characteristic zones. Cooling time was determined theoretically, numerically and experimentally.
PB  - Faculty of Metallurgy
T2  - Metalurgija
T1  - Selection of the optimal hard facing (HF) technology of damaged forging dies based on cooling time t8/5
EP  - 106
IS  - 1
SP  - 103
VL  - 55
UR  - https://hdl.handle.net/21.15107/rcub_machinery_2312
ER  - 

@article{
author = "Arsić, D. and Lazić, Vukić and Sedmak, Aleksandar and Nikolić, Ružica R. and Aleksandrović, Srbislav and Đorđević, M. and Bakić, Ramo",
year = "2016",
abstract = "In exploitation, the forging dies are exposed to heating up to very high temperatures, variable loads: compressive, impact and shear. In this paper, the reparatory hard facing of the damaged forging dies is considered. The objective was to establish the optimal reparatory technology based on cooling time t8/5. The verification of the adopted technology was done by investigation of the hard faced layers microstructure and measurements of hardness within the welded layers’ characteristic zones. Cooling time was determined theoretically, numerically and experimentally.",
publisher = "Faculty of Metallurgy",
journal = "Metalurgija",
title = "Selection of the optimal hard facing (HF) technology of damaged forging dies based on cooling time t8/5",
pages = "106-103",
number = "1",
volume = "55",
url = "https://hdl.handle.net/21.15107/rcub_machinery_2312"
}

Arsić, D., Lazić, V., Sedmak, A., Nikolić, R. R., Aleksandrović, S., Đorđević, M.,& Bakić, R.. (2016). Selection of the optimal hard facing (HF) technology of damaged forging dies based on cooling time t8/5. in Metalurgija
Faculty of Metallurgy., 55(1), 103-106.
https://hdl.handle.net/21.15107/rcub_machinery_2312

Arsić D, Lazić V, Sedmak A, Nikolić RR, Aleksandrović S, Đorđević M, Bakić R. Selection of the optimal hard facing (HF) technology of damaged forging dies based on cooling time t8/5. in Metalurgija. 2016;55(1):103-106.
https://hdl.handle.net/21.15107/rcub_machinery_2312 .

Arsić, D., Lazić, Vukić, Sedmak, Aleksandar, Nikolić, Ružica R., Aleksandrović, Srbislav, Đorđević, M., Bakić, Ramo, "Selection of the optimal hard facing (HF) technology of damaged forging dies based on cooling time t8/5" in Metalurgija, 55, no. 1 (2016):103-106,
https://hdl.handle.net/21.15107/rcub_machinery_2312 .

TY  - JOUR
AU  - Lazić, Vukić
AU  - Sedmak, Aleksandar
AU  - Nikolić, Ružica R.
AU  - Mutavdzić, Milan
AU  - Aleksandrović, Srbislav
AU  - Krstić, Božidar
AU  - Milosavljević, Dragan I.
PY  - 2015
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/2176
AB  - A possibility of extending the service life of the working parts of construction machinery with particular attention to hardfacing of loader bucket teeth was investigated. In the first part of this paper the tribological processes typical for this machinery is analysed. Worn excavator parts are made of conditionally weldable cast steel that requires a special hardfacing technology, so numerous investigations were performed to obtain the most appropriate technology. In the experimental part of the paper, the selection of the optimum hardfacing technology for bucket teeth and the procedure of the manual arc hardfacing are presented. The samples were first hardfaced using different techniques and technologies and then the microstructure and microhardness of characteristic hardfaced layers were studied. Specially prepared samples were used for tribological investigations. The results of experimental investigations enabled the selection of the most suitable hardfacing technology and its application to real parts. The bucket teeth, with their hardfaced layers applied vertically, horizontally or in a honeycomb pattern were mounted onto a loader bucket, alternated with the new non-hardfaced teeth and their performance during the operation was regularly monitored. After a certain period, the degrees of the wear for the non-hardfaced and differently hardfaced teeth were measured. Taking into account both technical and economic factors, the most suitable hardfacing technology was determined.
PB  - Institute of Metals Technology
T2  - Materiali in Tehnologije
T1  - Selection of the most appropriate welding technology for hardfacing of bucket teeth
EP  - 172
IS  - 1
SP  - 165
VL  - 49
UR  - https://hdl.handle.net/21.15107/rcub_machinery_2176
ER  - 

@article{
author = "Lazić, Vukić and Sedmak, Aleksandar and Nikolić, Ružica R. and Mutavdzić, Milan and Aleksandrović, Srbislav and Krstić, Božidar and Milosavljević, Dragan I.",
year = "2015",
abstract = "A possibility of extending the service life of the working parts of construction machinery with particular attention to hardfacing of loader bucket teeth was investigated. In the first part of this paper the tribological processes typical for this machinery is analysed. Worn excavator parts are made of conditionally weldable cast steel that requires a special hardfacing technology, so numerous investigations were performed to obtain the most appropriate technology. In the experimental part of the paper, the selection of the optimum hardfacing technology for bucket teeth and the procedure of the manual arc hardfacing are presented. The samples were first hardfaced using different techniques and technologies and then the microstructure and microhardness of characteristic hardfaced layers were studied. Specially prepared samples were used for tribological investigations. The results of experimental investigations enabled the selection of the most suitable hardfacing technology and its application to real parts. The bucket teeth, with their hardfaced layers applied vertically, horizontally or in a honeycomb pattern were mounted onto a loader bucket, alternated with the new non-hardfaced teeth and their performance during the operation was regularly monitored. After a certain period, the degrees of the wear for the non-hardfaced and differently hardfaced teeth were measured. Taking into account both technical and economic factors, the most suitable hardfacing technology was determined.",
publisher = "Institute of Metals Technology",
journal = "Materiali in Tehnologije",
title = "Selection of the most appropriate welding technology for hardfacing of bucket teeth",
pages = "172-165",
number = "1",
volume = "49",
url = "https://hdl.handle.net/21.15107/rcub_machinery_2176"
}

Lazić, V., Sedmak, A., Nikolić, R. R., Mutavdzić, M., Aleksandrović, S., Krstić, B.,& Milosavljević, D. I.. (2015). Selection of the most appropriate welding technology for hardfacing of bucket teeth. in Materiali in Tehnologije
Institute of Metals Technology., 49(1), 165-172.
https://hdl.handle.net/21.15107/rcub_machinery_2176

Lazić V, Sedmak A, Nikolić RR, Mutavdzić M, Aleksandrović S, Krstić B, Milosavljević DI. Selection of the most appropriate welding technology for hardfacing of bucket teeth. in Materiali in Tehnologije. 2015;49(1):165-172.
https://hdl.handle.net/21.15107/rcub_machinery_2176 .

Lazić, Vukić, Sedmak, Aleksandar, Nikolić, Ružica R., Mutavdzić, Milan, Aleksandrović, Srbislav, Krstić, Božidar, Milosavljević, Dragan I., "Selection of the most appropriate welding technology for hardfacing of bucket teeth" in Materiali in Tehnologije, 49, no. 1 (2015):165-172,
https://hdl.handle.net/21.15107/rcub_machinery_2176 .

TY  - JOUR
AU  - Lazić, Vukić
AU  - Sedmak, Aleksandar
AU  - Samardžić, I.
AU  - Aleksandrović, Srbislav
AU  - Arsić, D.
AU  - Milosavljević, Dragan I.
AU  - Đorđević, M.
PY  - 2015
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/2111
AB  - Complex working conditions of forging dies are the most frequent causes of their damage, requiring suitable hard facing repair procedures. The method of determining the bond strength between the hardfaced layer and the base material is explained in details, and the relation between hardfaced layer output results and the applied technology is established. Shear testing of materials has proven to be one of the most difficult areas of mechanical property testing. Shear modulus measurements are mainly accurate, but it is very difficult to measure shear strength. Edges, material coupling, non-pure shear loading, non-linear behaviour, imperfect stress distribution and coupling with normal stresses make shear strength determination difficult. None of the available test methods are without inaccuracies. Therefore, in structural applications, shear strength data should be used very carefully, on a case-by-case basis, appreciating the consequences of potential inaccuracies of the used values.
PB  - Institut za ispitivanje materijala, Beograd
T2  - Structural Integrity and Life
T1  - Shear strength testing of hardfaced samples using special tool on an universal testing machine
EP  - 18
IS  - 1
SP  - 15
VL  - 15
UR  - https://hdl.handle.net/21.15107/rcub_machinery_2111
ER  - 

@article{
author = "Lazić, Vukić and Sedmak, Aleksandar and Samardžić, I. and Aleksandrović, Srbislav and Arsić, D. and Milosavljević, Dragan I. and Đorđević, M.",
year = "2015",
abstract = "Complex working conditions of forging dies are the most frequent causes of their damage, requiring suitable hard facing repair procedures. The method of determining the bond strength between the hardfaced layer and the base material is explained in details, and the relation between hardfaced layer output results and the applied technology is established. Shear testing of materials has proven to be one of the most difficult areas of mechanical property testing. Shear modulus measurements are mainly accurate, but it is very difficult to measure shear strength. Edges, material coupling, non-pure shear loading, non-linear behaviour, imperfect stress distribution and coupling with normal stresses make shear strength determination difficult. None of the available test methods are without inaccuracies. Therefore, in structural applications, shear strength data should be used very carefully, on a case-by-case basis, appreciating the consequences of potential inaccuracies of the used values.",
publisher = "Institut za ispitivanje materijala, Beograd",
journal = "Structural Integrity and Life",
title = "Shear strength testing of hardfaced samples using special tool on an universal testing machine",
pages = "18-15",
number = "1",
volume = "15",
url = "https://hdl.handle.net/21.15107/rcub_machinery_2111"
}

Lazić, V., Sedmak, A., Samardžić, I., Aleksandrović, S., Arsić, D., Milosavljević, D. I.,& Đorđević, M.. (2015). Shear strength testing of hardfaced samples using special tool on an universal testing machine. in Structural Integrity and Life
Institut za ispitivanje materijala, Beograd., 15(1), 15-18.
https://hdl.handle.net/21.15107/rcub_machinery_2111

Lazić V, Sedmak A, Samardžić I, Aleksandrović S, Arsić D, Milosavljević DI, Đorđević M. Shear strength testing of hardfaced samples using special tool on an universal testing machine. in Structural Integrity and Life. 2015;15(1):15-18.
https://hdl.handle.net/21.15107/rcub_machinery_2111 .

Lazić, Vukić, Sedmak, Aleksandar, Samardžić, I., Aleksandrović, Srbislav, Arsić, D., Milosavljević, Dragan I., Đorđević, M., "Shear strength testing of hardfaced samples using special tool on an universal testing machine" in Structural Integrity and Life, 15, no. 1 (2015):15-18,
https://hdl.handle.net/21.15107/rcub_machinery_2111 .

TY  - JOUR
AU  - Lazić, Vukić
AU  - Ivanović, Ivana
AU  - Sedmak, Aleksandar
AU  - Rudolf, Rebeka
AU  - Lazić, Mirjana M.
AU  - Radaković, Zoran
PY  - 2014
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/1880
AB  - The three-dimensional transient nonlinear thermal analysis of the hard facing process is performed by using the finite element method. The simulations were executed on the open source Salome platform using the open source finite element solver Code Aster. The Gaussian double ellipsoid was selected in order to enable greater possibilities for the calculation of the moving heat source. The numerical results were compared with available experimental results.
PB  - Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd
T2  - Thermal Science
T1  - Numerical analysis of temperature field during hardfacing process and comparison with experimental results
EP  - S120
SP  - S113
VL  - 18
DO  - 10.2298/TSCI130117177L
ER  - 

@article{
author = "Lazić, Vukić and Ivanović, Ivana and Sedmak, Aleksandar and Rudolf, Rebeka and Lazić, Mirjana M. and Radaković, Zoran",
year = "2014",
abstract = "The three-dimensional transient nonlinear thermal analysis of the hard facing process is performed by using the finite element method. The simulations were executed on the open source Salome platform using the open source finite element solver Code Aster. The Gaussian double ellipsoid was selected in order to enable greater possibilities for the calculation of the moving heat source. The numerical results were compared with available experimental results.",
publisher = "Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd",
journal = "Thermal Science",
title = "Numerical analysis of temperature field during hardfacing process and comparison with experimental results",
pages = "S120-S113",
volume = "18",
doi = "10.2298/TSCI130117177L"
}

Lazić, V., Ivanović, I., Sedmak, A., Rudolf, R., Lazić, M. M.,& Radaković, Z.. (2014). Numerical analysis of temperature field during hardfacing process and comparison with experimental results. in Thermal Science
Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd., 18, S113-S120.
https://doi.org/10.2298/TSCI130117177L

Lazić V, Ivanović I, Sedmak A, Rudolf R, Lazić MM, Radaković Z. Numerical analysis of temperature field during hardfacing process and comparison with experimental results. in Thermal Science. 2014;18:S113-S120.
doi:10.2298/TSCI130117177L .

Lazić, Vukić, Ivanović, Ivana, Sedmak, Aleksandar, Rudolf, Rebeka, Lazić, Mirjana M., Radaković, Zoran, "Numerical analysis of temperature field during hardfacing process and comparison with experimental results" in Thermal Science, 18 (2014):S113-S120,
https://doi.org/10.2298/TSCI130117177L . .

TY  - CONF
AU  - Ivanović, Ivana
AU  - Sedmak, Aleksandar
AU  - Lazić, Vukić
PY  - 2013
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/1676
AB  - An initial goal of this study was to use the results from an existing experiment and to set up as complete as possible the numerical model for the thermal analysis of a hard surfacing process. It was clear from the start that the process is complex since it includes multiple weld passes, or several layers, which are elements difficult for experimental or numerical thermal modeling. When the design parameters for the set up of the numerical model have been identified, it was noticed that some of them were only partially recorded in the experiment. Conclusion was that it will be valuable to highlight those very necessary parameters.
PB  - Amer Inst Physics, Melville
C3  - 11th International Conference of Numerical Analysis and Applied Mathematics 2013, Pts 1 and 2 (Icnaa
T1  - Numerical Analysis of Thermal Conditions for Planning and Further Improvements of Hard Surfacing Experiment
EP  - 2418
SP  - 2414
VL  - 1558
DO  - 10.1063/1.4826028
ER  - 

@conference{
author = "Ivanović, Ivana and Sedmak, Aleksandar and Lazić, Vukić",
year = "2013",
abstract = "An initial goal of this study was to use the results from an existing experiment and to set up as complete as possible the numerical model for the thermal analysis of a hard surfacing process. It was clear from the start that the process is complex since it includes multiple weld passes, or several layers, which are elements difficult for experimental or numerical thermal modeling. When the design parameters for the set up of the numerical model have been identified, it was noticed that some of them were only partially recorded in the experiment. Conclusion was that it will be valuable to highlight those very necessary parameters.",
publisher = "Amer Inst Physics, Melville",
journal = "11th International Conference of Numerical Analysis and Applied Mathematics 2013, Pts 1 and 2 (Icnaa",
title = "Numerical Analysis of Thermal Conditions for Planning and Further Improvements of Hard Surfacing Experiment",
pages = "2418-2414",
volume = "1558",
doi = "10.1063/1.4826028"
}

Ivanović, I., Sedmak, A.,& Lazić, V.. (2013). Numerical Analysis of Thermal Conditions for Planning and Further Improvements of Hard Surfacing Experiment. in 11th International Conference of Numerical Analysis and Applied Mathematics 2013, Pts 1 and 2 (Icnaa
Amer Inst Physics, Melville., 1558, 2414-2418.
https://doi.org/10.1063/1.4826028

Ivanović I, Sedmak A, Lazić V. Numerical Analysis of Thermal Conditions for Planning and Further Improvements of Hard Surfacing Experiment. in 11th International Conference of Numerical Analysis and Applied Mathematics 2013, Pts 1 and 2 (Icnaa. 2013;1558:2414-2418.
doi:10.1063/1.4826028 .

Ivanović, Ivana, Sedmak, Aleksandar, Lazić, Vukić, "Numerical Analysis of Thermal Conditions for Planning and Further Improvements of Hard Surfacing Experiment" in 11th International Conference of Numerical Analysis and Applied Mathematics 2013, Pts 1 and 2 (Icnaa, 1558 (2013):2414-2418,
https://doi.org/10.1063/1.4826028 . .

TY  - JOUR
AU  - Lazić, Vukić
AU  - Sedmak, Aleksandar
AU  - Milosavljević, Dragan I.
AU  - Nikolić, Ilija
AU  - Aleksandrović, Srbislav
AU  - Nikolić, Ružica R.
AU  - Mutavdzić, Milan
PY  - 2012
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/1572
AB  - We have investigated the possibility of repairing damaged machine parts by hard facing with austenite-manganese steel electrodes. The subject is a Fe-C-Mn alloy with a microstructure of soft austenite which, after cold deformation, transforms by a shearing mechanism into a hard martensite microstructure. These steels are used mainly for parts exposed to high impact loads and intensive abrasive wear. Depending on the degree of wear, these parts can be replaced by new ones or repaired by hard facing. The selection of the optimal reparation technology for the rotational crusher's impact beams is the subject of this study. Investigations of model samples were conducted first, followed by layers hard faced onto samples with austenite manganese and special electrodes. After this the microstructure and hardness of the welds' characteristic zones were investigated. After reparatory hard facing the impact beams were mounted in the crusher and their behaviour was monitored periodically. Both the new and hard-faced beams' behaviours were monitored and compared under the same working conditions. In this way, the optimal technology for hard facing was established, taking into account not only the technical indicators, but also the economic effects.
PB  - Institute of Metals and Technology
T2  - Materiali in Tehnologije
T1  - Theoretical and experimental estimation of the working life of machine parts hard faced with austenite-manganese electrodes
EP  - 554
IS  - 5
SP  - 547
VL  - 46
UR  - https://hdl.handle.net/21.15107/rcub_machinery_1572
ER  - 

@article{
author = "Lazić, Vukić and Sedmak, Aleksandar and Milosavljević, Dragan I. and Nikolić, Ilija and Aleksandrović, Srbislav and Nikolić, Ružica R. and Mutavdzić, Milan",
year = "2012",
abstract = "We have investigated the possibility of repairing damaged machine parts by hard facing with austenite-manganese steel electrodes. The subject is a Fe-C-Mn alloy with a microstructure of soft austenite which, after cold deformation, transforms by a shearing mechanism into a hard martensite microstructure. These steels are used mainly for parts exposed to high impact loads and intensive abrasive wear. Depending on the degree of wear, these parts can be replaced by new ones or repaired by hard facing. The selection of the optimal reparation technology for the rotational crusher's impact beams is the subject of this study. Investigations of model samples were conducted first, followed by layers hard faced onto samples with austenite manganese and special electrodes. After this the microstructure and hardness of the welds' characteristic zones were investigated. After reparatory hard facing the impact beams were mounted in the crusher and their behaviour was monitored periodically. Both the new and hard-faced beams' behaviours were monitored and compared under the same working conditions. In this way, the optimal technology for hard facing was established, taking into account not only the technical indicators, but also the economic effects.",
publisher = "Institute of Metals and Technology",
journal = "Materiali in Tehnologije",
title = "Theoretical and experimental estimation of the working life of machine parts hard faced with austenite-manganese electrodes",
pages = "554-547",
number = "5",
volume = "46",
url = "https://hdl.handle.net/21.15107/rcub_machinery_1572"
}

Lazić, V., Sedmak, A., Milosavljević, D. I., Nikolić, I., Aleksandrović, S., Nikolić, R. R.,& Mutavdzić, M.. (2012). Theoretical and experimental estimation of the working life of machine parts hard faced with austenite-manganese electrodes. in Materiali in Tehnologije
Institute of Metals and Technology., 46(5), 547-554.
https://hdl.handle.net/21.15107/rcub_machinery_1572

Lazić V, Sedmak A, Milosavljević DI, Nikolić I, Aleksandrović S, Nikolić RR, Mutavdzić M. Theoretical and experimental estimation of the working life of machine parts hard faced with austenite-manganese electrodes. in Materiali in Tehnologije. 2012;46(5):547-554.
https://hdl.handle.net/21.15107/rcub_machinery_1572 .

Lazić, Vukić, Sedmak, Aleksandar, Milosavljević, Dragan I., Nikolić, Ilija, Aleksandrović, Srbislav, Nikolić, Ružica R., Mutavdzić, Milan, "Theoretical and experimental estimation of the working life of machine parts hard faced with austenite-manganese electrodes" in Materiali in Tehnologije, 46, no. 5 (2012):547-554,
https://hdl.handle.net/21.15107/rcub_machinery_1572 .

TY  - CONF
AU  - Lazić, Vukić
AU  - Aleksandrović, Srbislav
AU  - Nikolić, Ružica R.
AU  - Prokić-Cvetković, Radica
AU  - Popović, Olivera
AU  - Milosavljević, Dragan I.
AU  - Čukić, Rajko D.
PY  - 2012
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/1378
AB  - High strength steels belong into a group of high quality steels, with exceptional mechanical properties, especially in regards to tensile strength. At the same time, as their deficiency is emphasized the limited and difficult weldability. In other words, some of those steels are weldable only with application of special measures related to controlled heat input. In that way, the favorable mechanical properties can be kept within the heat affected zone, with condition that the optimal welding technology is selected. Existing, very scarce and often unclear and insufficient recommendations for selection of the optimal welding technology are one of the causes of large number of flaws in welded joints. Mentioned problems, as well as others, can be successfully solved by proper selection of the procedure, filler metal and technology of welding, verified by experiments conducted in laboratory or in real operating conditions. Those experiments can not be performed in arbitrary conditions. Thus, partially due to results reported in this paper, technologists will obtain the possibility to predict in advance, in a very short time period, the mechanical and metallurgical properties of joints of this class of high strength steels. This will be possible without conducting the large number of practical tests or relying on personal experience of a designer.
PB  - Elsevier Science Bv, Amsterdam
C3  - Steel Structures and Bridges 2012 - 23rd Czech and Slovak International Conference
T1  - Estimates of weldability and selection of the optimal procedure and technology for welding of high strength steels
EP  - 315
SP  - 310
VL  - 40
DO  - 10.1016/j.proeng.2012.07.100
ER  - 

@conference{
author = "Lazić, Vukić and Aleksandrović, Srbislav and Nikolić, Ružica R. and Prokić-Cvetković, Radica and Popović, Olivera and Milosavljević, Dragan I. and Čukić, Rajko D.",
year = "2012",
abstract = "High strength steels belong into a group of high quality steels, with exceptional mechanical properties, especially in regards to tensile strength. At the same time, as their deficiency is emphasized the limited and difficult weldability. In other words, some of those steels are weldable only with application of special measures related to controlled heat input. In that way, the favorable mechanical properties can be kept within the heat affected zone, with condition that the optimal welding technology is selected. Existing, very scarce and often unclear and insufficient recommendations for selection of the optimal welding technology are one of the causes of large number of flaws in welded joints. Mentioned problems, as well as others, can be successfully solved by proper selection of the procedure, filler metal and technology of welding, verified by experiments conducted in laboratory or in real operating conditions. Those experiments can not be performed in arbitrary conditions. Thus, partially due to results reported in this paper, technologists will obtain the possibility to predict in advance, in a very short time period, the mechanical and metallurgical properties of joints of this class of high strength steels. This will be possible without conducting the large number of practical tests or relying on personal experience of a designer.",
publisher = "Elsevier Science Bv, Amsterdam",
journal = "Steel Structures and Bridges 2012 - 23rd Czech and Slovak International Conference",
title = "Estimates of weldability and selection of the optimal procedure and technology for welding of high strength steels",
pages = "315-310",
volume = "40",
doi = "10.1016/j.proeng.2012.07.100"
}

Lazić, V., Aleksandrović, S., Nikolić, R. R., Prokić-Cvetković, R., Popović, O., Milosavljević, D. I.,& Čukić, R. D.. (2012). Estimates of weldability and selection of the optimal procedure and technology for welding of high strength steels. in Steel Structures and Bridges 2012 - 23rd Czech and Slovak International Conference
Elsevier Science Bv, Amsterdam., 40, 310-315.
https://doi.org/10.1016/j.proeng.2012.07.100

Lazić V, Aleksandrović S, Nikolić RR, Prokić-Cvetković R, Popović O, Milosavljević DI, Čukić RD. Estimates of weldability and selection of the optimal procedure and technology for welding of high strength steels. in Steel Structures and Bridges 2012 - 23rd Czech and Slovak International Conference. 2012;40:310-315.
doi:10.1016/j.proeng.2012.07.100 .

Lazić, Vukić, Aleksandrović, Srbislav, Nikolić, Ružica R., Prokić-Cvetković, Radica, Popović, Olivera, Milosavljević, Dragan I., Čukić, Rajko D., "Estimates of weldability and selection of the optimal procedure and technology for welding of high strength steels" in Steel Structures and Bridges 2012 - 23rd Czech and Slovak International Conference, 40 (2012):310-315,
https://doi.org/10.1016/j.proeng.2012.07.100 . .

TY  - JOUR
AU  - Lazić, Vukić
AU  - Jovanović, Milorad D.
AU  - Sedmak, Aleksandar
AU  - Aleksandrović, Srbislav
AU  - Milosavljević, Dragan I.
AU  - Krstić, Božidar
AU  - Čukić, Rajko D.
PY  - 2010
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/1088
AB  - This paper studies problems of hard facing of damaged and initially cracked mechanical engineering heavy parts of complex geometry such as large rams of air powered drop hammers. During long-term exploitation, these parts are subjected to thermal fatigue due to cyclic temperature changes and variable impact compression. Taking into consideration high ram costs and difficulties to purchase ram, the necessity of its reparation becomes obvious. The choices of the most suitable technologies of hard facing and welding of an initially cracked ram are also studied here. Besides the techno-economic analysis, an energetic analysis is performed as an additional criterion in assessment of the proposed technology.
PB  - Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd
T2  - Thermal Science
T1  - Energetic analysis of hard facing and weld cladding of an air powered drop hammer damaged ram
EP  - S284
SP  - S269
VL  - 14
DO  - 10.2298/TSCI100501021L
ER  - 

@article{
author = "Lazić, Vukić and Jovanović, Milorad D. and Sedmak, Aleksandar and Aleksandrović, Srbislav and Milosavljević, Dragan I. and Krstić, Božidar and Čukić, Rajko D.",
year = "2010",
abstract = "This paper studies problems of hard facing of damaged and initially cracked mechanical engineering heavy parts of complex geometry such as large rams of air powered drop hammers. During long-term exploitation, these parts are subjected to thermal fatigue due to cyclic temperature changes and variable impact compression. Taking into consideration high ram costs and difficulties to purchase ram, the necessity of its reparation becomes obvious. The choices of the most suitable technologies of hard facing and welding of an initially cracked ram are also studied here. Besides the techno-economic analysis, an energetic analysis is performed as an additional criterion in assessment of the proposed technology.",
publisher = "Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd",
journal = "Thermal Science",
title = "Energetic analysis of hard facing and weld cladding of an air powered drop hammer damaged ram",
pages = "S284-S269",
volume = "14",
doi = "10.2298/TSCI100501021L"
}

Lazić, V., Jovanović, M. D., Sedmak, A., Aleksandrović, S., Milosavljević, D. I., Krstić, B.,& Čukić, R. D.. (2010). Energetic analysis of hard facing and weld cladding of an air powered drop hammer damaged ram. in Thermal Science
Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd., 14, S269-S284.
https://doi.org/10.2298/TSCI100501021L

Lazić V, Jovanović MD, Sedmak A, Aleksandrović S, Milosavljević DI, Krstić B, Čukić RD. Energetic analysis of hard facing and weld cladding of an air powered drop hammer damaged ram. in Thermal Science. 2010;14:S269-S284.
doi:10.2298/TSCI100501021L .

Lazić, Vukić, Jovanović, Milorad D., Sedmak, Aleksandar, Aleksandrović, Srbislav, Milosavljević, Dragan I., Krstić, Božidar, Čukić, Rajko D., "Energetic analysis of hard facing and weld cladding of an air powered drop hammer damaged ram" in Thermal Science, 14 (2010):S269-S284,
https://doi.org/10.2298/TSCI100501021L . .

TY  - JOUR
AU  - Lazić, Vukić
AU  - Sedmak, Aleksandar
AU  - Živković, Miroslav M.
AU  - Aleksandrović, Srbislav
AU  - Čukić, Rajko D.
AU  - Jovičić, Radomir
AU  - Ivanović, Ivana
PY  - 2010
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/1125
AB  - This paper investigates the accuracy of analytical, empirical, and numerical expressions, i. e. the most favourable methods for calculating the cooling time from 800 to 500°C (t8/5). The degree of accuracy of time t8/5 is very significant, because it determines the cooling rate, and consequently the structural changes in heat affected zone for hard faced layers. Based on the presented results, one can conclude that the finite element method provides the best conformity with the experiment and among analytical and empirical formulas the same goes for the expression of Japanese authors, for the case of hard facing of plane and prismatic parts.
PB  - Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd
T2  - Thermal Science
T1  - Theoretical-experimental determining of cooling time (t8/5) in hard facing of steels for forging dies
EP  - 246
IS  - 1
SP  - 235
VL  - 14
DO  - 10.2298/TSCI1001235L
ER  - 

@article{
author = "Lazić, Vukić and Sedmak, Aleksandar and Živković, Miroslav M. and Aleksandrović, Srbislav and Čukić, Rajko D. and Jovičić, Radomir and Ivanović, Ivana",
year = "2010",
abstract = "This paper investigates the accuracy of analytical, empirical, and numerical expressions, i. e. the most favourable methods for calculating the cooling time from 800 to 500°C (t8/5). The degree of accuracy of time t8/5 is very significant, because it determines the cooling rate, and consequently the structural changes in heat affected zone for hard faced layers. Based on the presented results, one can conclude that the finite element method provides the best conformity with the experiment and among analytical and empirical formulas the same goes for the expression of Japanese authors, for the case of hard facing of plane and prismatic parts.",
publisher = "Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd",
journal = "Thermal Science",
title = "Theoretical-experimental determining of cooling time (t8/5) in hard facing of steels for forging dies",
pages = "246-235",
number = "1",
volume = "14",
doi = "10.2298/TSCI1001235L"
}

Lazić, V., Sedmak, A., Živković, M. M., Aleksandrović, S., Čukić, R. D., Jovičić, R.,& Ivanović, I.. (2010). Theoretical-experimental determining of cooling time (t8/5) in hard facing of steels for forging dies. in Thermal Science
Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd., 14(1), 235-246.
https://doi.org/10.2298/TSCI1001235L

Lazić V, Sedmak A, Živković MM, Aleksandrović S, Čukić RD, Jovičić R, Ivanović I. Theoretical-experimental determining of cooling time (t8/5) in hard facing of steels for forging dies. in Thermal Science. 2010;14(1):235-246.
doi:10.2298/TSCI1001235L .

Lazić, Vukić, Sedmak, Aleksandar, Živković, Miroslav M., Aleksandrović, Srbislav, Čukić, Rajko D., Jovičić, Radomir, Ivanović, Ivana, "Theoretical-experimental determining of cooling time (t8/5) in hard facing of steels for forging dies" in Thermal Science, 14, no. 1 (2010):235-246,
https://doi.org/10.2298/TSCI1001235L . .

TY  - JOUR
AU  - Ratković, Nada
AU  - Sedmak, Aleksandar
AU  - Jovanović, Milorad
AU  - Lazić, Vukić
AU  - Nikolić, Ružica R.
AU  - Krstić, Božidar
PY  - 2009
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/871
AB  - This paper outlines the basic principles of welding by friction of high-speed cutting steel and tempered steel from the viewpoint of metallurgic processes that are going on in the material. The bases of welding by friction of different materials are outlined in a theoretical way. The experimental part of the paper also relates to friction welding of samples made of different metals: high-speed cutting steel (HS 6-5-2-5) on one handand the tempered steel (C60) on the other.
PB  - Faculty of Mechanical Engineering in Slavonski Brod, Faculty of Electrical Engineering in Osijek, Faculty of Civil Engineering in Osijek
T2  - Tehnički vjesnik
T1  - Physical and metallurgic changes during the friction welding of high-speed cutting steel and tempered steel
EP  - 31
IS  - 3
SP  - 27
VL  - 16
UR  - https://hdl.handle.net/21.15107/rcub_machinery_871
ER  - 

@article{
author = "Ratković, Nada and Sedmak, Aleksandar and Jovanović, Milorad and Lazić, Vukić and Nikolić, Ružica R. and Krstić, Božidar",
year = "2009",
abstract = "This paper outlines the basic principles of welding by friction of high-speed cutting steel and tempered steel from the viewpoint of metallurgic processes that are going on in the material. The bases of welding by friction of different materials are outlined in a theoretical way. The experimental part of the paper also relates to friction welding of samples made of different metals: high-speed cutting steel (HS 6-5-2-5) on one handand the tempered steel (C60) on the other.",
publisher = "Faculty of Mechanical Engineering in Slavonski Brod, Faculty of Electrical Engineering in Osijek, Faculty of Civil Engineering in Osijek",
journal = "Tehnički vjesnik",
title = "Physical and metallurgic changes during the friction welding of high-speed cutting steel and tempered steel",
pages = "31-27",
number = "3",
volume = "16",
url = "https://hdl.handle.net/21.15107/rcub_machinery_871"
}

Ratković, N., Sedmak, A., Jovanović, M., Lazić, V., Nikolić, R. R.,& Krstić, B.. (2009). Physical and metallurgic changes during the friction welding of high-speed cutting steel and tempered steel. in Tehnički vjesnik
Faculty of Mechanical Engineering in Slavonski Brod, Faculty of Electrical Engineering in Osijek, Faculty of Civil Engineering in Osijek., 16(3), 27-31.
https://hdl.handle.net/21.15107/rcub_machinery_871

Ratković N, Sedmak A, Jovanović M, Lazić V, Nikolić RR, Krstić B. Physical and metallurgic changes during the friction welding of high-speed cutting steel and tempered steel. in Tehnički vjesnik. 2009;16(3):27-31.
https://hdl.handle.net/21.15107/rcub_machinery_871 .

Ratković, Nada, Sedmak, Aleksandar, Jovanović, Milorad, Lazić, Vukić, Nikolić, Ružica R., Krstić, Božidar, "Physical and metallurgic changes during the friction welding of high-speed cutting steel and tempered steel" in Tehnički vjesnik, 16, no. 3 (2009):27-31,
https://hdl.handle.net/21.15107/rcub_machinery_871 .

TY  - JOUR
AU  - Ratković, Nada
AU  - Sedmak, Aleksandar
AU  - Jovanović, Milorad
AU  - Lazić, Vukić
AU  - Nikolić, Ružica R.
AU  - Krstić, Božidar
PY  - 2009
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/870
AB  - This paper outlines the bases of the friction welding process, especially when it comes to friction welding of different materials. This was illustrated on an example of friction welding of aluminum and copper, which is often applied in electrical engineering. The analysis of influential parameters was conducted based on the data obtained by an experiment, since the data on this topic are very seldom in the available literature.
PB  - Faculty of Mechanical Engineering in Slavonski Brod, Faculty of Electrical Engineering in Osijek, Faculty of Civil Engineering in Osijek
T2  - Tehnički vjesnik
T1  - Quality analysis of ai-cu joint realized by friction welding
EP  - 7
IS  - 3
SP  - 3
VL  - 16
UR  - https://hdl.handle.net/21.15107/rcub_machinery_870
ER  - 

@article{
author = "Ratković, Nada and Sedmak, Aleksandar and Jovanović, Milorad and Lazić, Vukić and Nikolić, Ružica R. and Krstić, Božidar",
year = "2009",
abstract = "This paper outlines the bases of the friction welding process, especially when it comes to friction welding of different materials. This was illustrated on an example of friction welding of aluminum and copper, which is often applied in electrical engineering. The analysis of influential parameters was conducted based on the data obtained by an experiment, since the data on this topic are very seldom in the available literature.",
publisher = "Faculty of Mechanical Engineering in Slavonski Brod, Faculty of Electrical Engineering in Osijek, Faculty of Civil Engineering in Osijek",
journal = "Tehnički vjesnik",
title = "Quality analysis of ai-cu joint realized by friction welding",
pages = "7-3",
number = "3",
volume = "16",
url = "https://hdl.handle.net/21.15107/rcub_machinery_870"
}

Ratković, N., Sedmak, A., Jovanović, M., Lazić, V., Nikolić, R. R.,& Krstić, B.. (2009). Quality analysis of ai-cu joint realized by friction welding. in Tehnički vjesnik
Faculty of Mechanical Engineering in Slavonski Brod, Faculty of Electrical Engineering in Osijek, Faculty of Civil Engineering in Osijek., 16(3), 3-7.
https://hdl.handle.net/21.15107/rcub_machinery_870

Ratković N, Sedmak A, Jovanović M, Lazić V, Nikolić RR, Krstić B. Quality analysis of ai-cu joint realized by friction welding. in Tehnički vjesnik. 2009;16(3):3-7.
https://hdl.handle.net/21.15107/rcub_machinery_870 .

Ratković, Nada, Sedmak, Aleksandar, Jovanović, Milorad, Lazić, Vukić, Nikolić, Ružica R., Krstić, Božidar, "Quality analysis of ai-cu joint realized by friction welding" in Tehnički vjesnik, 16, no. 3 (2009):3-7,
https://hdl.handle.net/21.15107/rcub_machinery_870 .

TY  - JOUR
AU  - Lazić, Vukić
AU  - Sedmak, Aleksandar
AU  - Aleksandrović, Srbislav
AU  - Milosavljević, Dragan I.
AU  - Čukić, Rajko D.
AU  - Grabulov, Vencislav
PY  - 2009
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/865
AB  - In this paper the problems related to the maintenance of large forging mallets of pneumatic hammers including hard facing of cracked or worn working surfaces are considered. Actually, the choice of optimum technology for the reparation of hard facing of the broken forging press frame and cracked mallet of the forging pneumatic hammer are taken into consideration.
PB  - Faculty of Mechanical Engineering in Slavonski Brod, Faculty of Electrical Engineering in Osijek, Faculty of Civil Engineering in Osijek
T2  - Tehnički vjesnik
T1  - Reparation of the damaged forging hammer mallet by hard facing and weld cladding
EP  - 113
IS  - 4
SP  - 107
VL  - 16
UR  - https://hdl.handle.net/21.15107/rcub_machinery_865
ER  - 

@article{
author = "Lazić, Vukić and Sedmak, Aleksandar and Aleksandrović, Srbislav and Milosavljević, Dragan I. and Čukić, Rajko D. and Grabulov, Vencislav",
year = "2009",
abstract = "In this paper the problems related to the maintenance of large forging mallets of pneumatic hammers including hard facing of cracked or worn working surfaces are considered. Actually, the choice of optimum technology for the reparation of hard facing of the broken forging press frame and cracked mallet of the forging pneumatic hammer are taken into consideration.",
publisher = "Faculty of Mechanical Engineering in Slavonski Brod, Faculty of Electrical Engineering in Osijek, Faculty of Civil Engineering in Osijek",
journal = "Tehnički vjesnik",
title = "Reparation of the damaged forging hammer mallet by hard facing and weld cladding",
pages = "113-107",
number = "4",
volume = "16",
url = "https://hdl.handle.net/21.15107/rcub_machinery_865"
}

Lazić, V., Sedmak, A., Aleksandrović, S., Milosavljević, D. I., Čukić, R. D.,& Grabulov, V.. (2009). Reparation of the damaged forging hammer mallet by hard facing and weld cladding. in Tehnički vjesnik
Faculty of Mechanical Engineering in Slavonski Brod, Faculty of Electrical Engineering in Osijek, Faculty of Civil Engineering in Osijek., 16(4), 107-113.
https://hdl.handle.net/21.15107/rcub_machinery_865

Lazić V, Sedmak A, Aleksandrović S, Milosavljević DI, Čukić RD, Grabulov V. Reparation of the damaged forging hammer mallet by hard facing and weld cladding. in Tehnički vjesnik. 2009;16(4):107-113.
https://hdl.handle.net/21.15107/rcub_machinery_865 .

Lazić, Vukić, Sedmak, Aleksandar, Aleksandrović, Srbislav, Milosavljević, Dragan I., Čukić, Rajko D., Grabulov, Vencislav, "Reparation of the damaged forging hammer mallet by hard facing and weld cladding" in Tehnički vjesnik, 16, no. 4 (2009):107-113,
https://hdl.handle.net/21.15107/rcub_machinery_865 .