THE INFLUENCE OF CYLLINDRICAL SPECIMEN GEOMETRY ON THE VALUES OF FRACTURE MECHANICS PARAMETERS
2023
Аутори
Trajković, IsaakMilošević, Miloš
Mitrović, Nenad
Sedmak, Aleksandar
Rakin, Marko
Međo, Bojan
Конференцијски прилог (Објављена верзија)
Метаподаци
Приказ свих података о документуАпстракт
A global problem for industrial plants that contain process equipment operating under high pressure is the assessment of the integrity of the equipment, specifically the pipelines. Standard procedures for determining fracture mechanics parameters (ASTM E1820) for materials used in pressure piping construction cannot be applied to most thin-wall pressure components. One of the solutions to this problem is the introduction of new procedures and geometries of test specimens. In order to understand the nature of the behavior of the specimens and to determine the parameters whose critical values are important for integrity assessment of the pipeline under pressure, a detailed analysis of the model of the non-standard ring-shaped specimen is
necessary. This paper will present the results of the analysis of fracture mechanics parameters obtained by the finite element method using the Simulia Abaqus software package. The properties of the material used in the software correspond to the proper...ties of the P235TR1 pipeline material obtained by tensile testing on cylindrical samples with initial crack. The ratio of crack length (a) to sample width (W) corresponds to standard sample geometries and varies from a/W = 0.4 to a/W = 0.6. The values obtained from SENT (Single Edge Notched Tension) models with the same cross-section and a/W ratio were taken as reference values in relation to which the comparison is made. As a result of this research, the ratio of fracture mechanics parameters of the ring-shaped model (Pipe Ring Notched Tension – PRNT specimen) with a crack and the SENT model was obtained. The values of the J-integral were also obtained, distribution of values along the crack front does not correspond to the profile obtained on the SENT model. As a result of this test, a procedure for determining the critical value of the J-integral for models corresponding to the tested P235TR1 pipe samples was established, which is an important step in establishing a new procedure for testing of pipeline materials.
Кључне речи:
Fracture mechanics / Pipeline / Single Edge Notched Tension specimen - SENT / Pipe Ring Notched Tension specimen – PRNT / Stress intensity factorИзвор:
International Conference of Experimental and Numerical Investigations and New Technologies CNN TECH 2023, 2023, 26-Издавач:
- University of Belgrade - Faculty of Mechanical Engineering
Колекције
Институција/група
Mašinski fakultetTY - CONF AU - Trajković, Isaak AU - Milošević, Miloš AU - Mitrović, Nenad AU - Sedmak, Aleksandar AU - Rakin, Marko AU - Međo, Bojan PY - 2023 UR - https://machinery.mas.bg.ac.rs/handle/123456789/7700 AB - A global problem for industrial plants that contain process equipment operating under high pressure is the assessment of the integrity of the equipment, specifically the pipelines. Standard procedures for determining fracture mechanics parameters (ASTM E1820) for materials used in pressure piping construction cannot be applied to most thin-wall pressure components. One of the solutions to this problem is the introduction of new procedures and geometries of test specimens. In order to understand the nature of the behavior of the specimens and to determine the parameters whose critical values are important for integrity assessment of the pipeline under pressure, a detailed analysis of the model of the non-standard ring-shaped specimen is necessary. This paper will present the results of the analysis of fracture mechanics parameters obtained by the finite element method using the Simulia Abaqus software package. The properties of the material used in the software correspond to the properties of the P235TR1 pipeline material obtained by tensile testing on cylindrical samples with initial crack. The ratio of crack length (a) to sample width (W) corresponds to standard sample geometries and varies from a/W = 0.4 to a/W = 0.6. The values obtained from SENT (Single Edge Notched Tension) models with the same cross-section and a/W ratio were taken as reference values in relation to which the comparison is made. As a result of this research, the ratio of fracture mechanics parameters of the ring-shaped model (Pipe Ring Notched Tension – PRNT specimen) with a crack and the SENT model was obtained. The values of the J-integral were also obtained, distribution of values along the crack front does not correspond to the profile obtained on the SENT model. As a result of this test, a procedure for determining the critical value of the J-integral for models corresponding to the tested P235TR1 pipe samples was established, which is an important step in establishing a new procedure for testing of pipeline materials. PB - University of Belgrade - Faculty of Mechanical Engineering C3 - International Conference of Experimental and Numerical Investigations and New Technologies CNN TECH 2023 T1 - THE INFLUENCE OF CYLLINDRICAL SPECIMEN GEOMETRY ON THE VALUES OF FRACTURE MECHANICS PARAMETERS SP - 26 UR - https://hdl.handle.net/21.15107/rcub_machinery_7700 ER -
@conference{ author = "Trajković, Isaak and Milošević, Miloš and Mitrović, Nenad and Sedmak, Aleksandar and Rakin, Marko and Međo, Bojan", year = "2023", abstract = "A global problem for industrial plants that contain process equipment operating under high pressure is the assessment of the integrity of the equipment, specifically the pipelines. Standard procedures for determining fracture mechanics parameters (ASTM E1820) for materials used in pressure piping construction cannot be applied to most thin-wall pressure components. One of the solutions to this problem is the introduction of new procedures and geometries of test specimens. In order to understand the nature of the behavior of the specimens and to determine the parameters whose critical values are important for integrity assessment of the pipeline under pressure, a detailed analysis of the model of the non-standard ring-shaped specimen is necessary. This paper will present the results of the analysis of fracture mechanics parameters obtained by the finite element method using the Simulia Abaqus software package. The properties of the material used in the software correspond to the properties of the P235TR1 pipeline material obtained by tensile testing on cylindrical samples with initial crack. The ratio of crack length (a) to sample width (W) corresponds to standard sample geometries and varies from a/W = 0.4 to a/W = 0.6. The values obtained from SENT (Single Edge Notched Tension) models with the same cross-section and a/W ratio were taken as reference values in relation to which the comparison is made. As a result of this research, the ratio of fracture mechanics parameters of the ring-shaped model (Pipe Ring Notched Tension – PRNT specimen) with a crack and the SENT model was obtained. The values of the J-integral were also obtained, distribution of values along the crack front does not correspond to the profile obtained on the SENT model. As a result of this test, a procedure for determining the critical value of the J-integral for models corresponding to the tested P235TR1 pipe samples was established, which is an important step in establishing a new procedure for testing of pipeline materials.", publisher = "University of Belgrade - Faculty of Mechanical Engineering", journal = "International Conference of Experimental and Numerical Investigations and New Technologies CNN TECH 2023", title = "THE INFLUENCE OF CYLLINDRICAL SPECIMEN GEOMETRY ON THE VALUES OF FRACTURE MECHANICS PARAMETERS", pages = "26", url = "https://hdl.handle.net/21.15107/rcub_machinery_7700" }
Trajković, I., Milošević, M., Mitrović, N., Sedmak, A., Rakin, M.,& Međo, B.. (2023). THE INFLUENCE OF CYLLINDRICAL SPECIMEN GEOMETRY ON THE VALUES OF FRACTURE MECHANICS PARAMETERS. in International Conference of Experimental and Numerical Investigations and New Technologies CNN TECH 2023 University of Belgrade - Faculty of Mechanical Engineering., 26. https://hdl.handle.net/21.15107/rcub_machinery_7700
Trajković I, Milošević M, Mitrović N, Sedmak A, Rakin M, Međo B. THE INFLUENCE OF CYLLINDRICAL SPECIMEN GEOMETRY ON THE VALUES OF FRACTURE MECHANICS PARAMETERS. in International Conference of Experimental and Numerical Investigations and New Technologies CNN TECH 2023. 2023;:26. https://hdl.handle.net/21.15107/rcub_machinery_7700 .
Trajković, Isaak, Milošević, Miloš, Mitrović, Nenad, Sedmak, Aleksandar, Rakin, Marko, Međo, Bojan, "THE INFLUENCE OF CYLLINDRICAL SPECIMEN GEOMETRY ON THE VALUES OF FRACTURE MECHANICS PARAMETERS" in International Conference of Experimental and Numerical Investigations and New Technologies CNN TECH 2023 (2023):26, https://hdl.handle.net/21.15107/rcub_machinery_7700 .