Претраживање
Приказ резултата 11-20 од 37
Procena integriteta posuda pod pritiskom sa greškom u zavarenom spoju / Structural integrity assessment of pressure vessels with defect in welded joints
(Vojnotehnički institut, Beograd, 2007)
U radu su prikazani primeri primene parametara mehanike loma za procenu integriteta posuda pod pritiskom sa prslinom. Primena parametara mehanike loma zavisi od niz podataka, pre svega o ponašanju materijala u prisustvu ...
Ponašanje pri zamoru i lomu zavarenih spojeva čelika NIOMOL 490K / Fracture and fatigue behavior of NIOMOL 490K welded joint
(Institut za ispitivanje materijala, Beograd, 2008)
Cilj rada je ispitivanje epruveta radi analize ponašanja prslina u zavarenim spojevima posuda pod pritiskom izrađenim od mikrolegiranog čelika, primenom parametara mehanike loma. Čelik NIOMOL 490K je namenjen za izradu ...
Effect of temperature and exploitation time on tensile properties and plain strain fracture toughness, K-Ic, in a welded joint
(Elsevier Science Bv, Amsterdam, 2018)
Effect of temperature and exploitation time on resistance to brittle fracture of welded joint constituents of new and 40 years exploited low-alloyed Cr-Mo steel A-387 Gr. B has been analysed. The plane strain fracture ...
Scenario razvoja loma u rotorskom bageru / Scenario of fracture development in bucket wheel excavator
(Institut za ispitivanje materijala, Beograd, 2013)
Produženi rad rotorskog bagera (BWE) u teškim radnim uslovima može dovesti do otkaza mašina. Kod veoma važnih elemenata konstrukcije, može dovesti do katastrofalnog loma. Lociranje važnih elemenata konstrukcije je od ...
Impact of temperature and exploitation time on plane strain fracture toughness, k-ic, in a welded joint
(Institut za ispitivanje materijala, Beograd, 2017)
This paper presents the analysis of the impact of temperature and exploitation time on the tendency toward brittle fracture of welded joint constituents of new and exploited low-alloyed Cr-Mo steel A-387 Gr. B, by using ...
Influence of temperature and exploitation time on hardness and micro-structure of a welded joint in a reactor mantle
(Elsevier Science Bv, Amsterdam, 2018)
This paper presents the analysis of the influence of temperature and exploitation time on the cross-sectional hardness and microstructure changes of characteristic zones of a welded joint made of low-alloyed Cr-Mo steel ...
Curenje posude za skladištenje CO2 od austenitnog čelika / Leakage of an austenitic steel CO2 storage tank
(Institut za ispitivanje materijala, Beograd, 2012)
Posle pojave vodenih kapi na spoljašnjem zidu otvora za reviziju posude za skladištenje ugljen dioksida, detaljnom inspekcijom je otkrivena mreža prslina na prirubnici revizionog otvora, blizu zavarenog spoja između ...
Measurement of local tensile properties of welded joint using digital image correlation method
(Chemicke Listy, 2012)
M. Milosevic(a), N. Mitrovic(b), R. Jovicic(a), A. Sedmak(b), T. Maneski(b), A. Petrovic(b), and T. Aburuga(b) ((a)Innovation Center of Faculty of Mechanical Engineering, b Faculty of Mechanical Engineering, University of ...
The influence of buffer layer on the properties of surface welded joint of high-carbon steel
(Institute of Metals and Technology, 2011)
Surface welding with buffer layer is often in use because of its well-known properties of plasticity, or ability to slow crack growth initiated. However, in modern surface welding technologies, buffer layer is rarely used. ...
Crack growth resistance of weldment constituents
(Elsevier Science Bv, Amsterdam, 2018)
The ovennatching can affect the occurrence of cold cracks after welding in high-strength low-alloyed steels of 770 MPa yield strength class. The welding consumable has been designed in a way to produce WM with slightly ...