TY  - JOUR
AU  - Djoković, Vladimir
AU  - Dudić, Duško
AU  - Dojčilović, Radovan
AU  - Marinković, Filip
AU  - Pavlović, Vera P.
AU  - Pavlović, Vladimir B.
AU  - Vlahović, Branislav
PY  - 2023
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/7061
AB  - Barium titanate (BT) perovskite particles were surface modified by means of mechanical treatment and used as inorganic component in polyvinylidene fluoride (PVDF) based composites. The changes in electrical properties of the composite films with increasing in filler content were followed by dielectric spectroscopy, breakdown strength and D-E measurements. A comparison of the properties of the composites prepared with untreated and mechanically activated particles revealed that there is a significant difference in their performances at low filler concentrations (<20 wt%). Introduction of the surface modified ceramic particles into PVDF matrix led to an increase of the dielectric constant without affecting significantly the electrical breakdown strength. In contrast, when as received BT particles were used a filler, both dielectric constants and breakdown strengths of the composite films were lower than the corresponding values observed for the pure PVDF. At higher concentrations, however, the influence of pre-treatment of the filler on the effective electrical properties becomes less significant. The obtained results were discussed in terms of the pronounced crystallization of polar β and γ crystal phases of PVDF in the presence of surface modified BT fillers, which is confirmed by Raman spectroscopy.
PB  - IOP Publishing Ltd
T2  - Physica Scripta
T1  - Toward improved PVDF-BaTiO3 composite dielectrics: mechanical activation of the filler versus filler content
IS  - 11
SP  - 115932
VL  - 98
DO  - 10.1088/1402-4896/acff4d
ER  - 

@article{
author = "Djoković, Vladimir and Dudić, Duško and Dojčilović, Radovan and Marinković, Filip and Pavlović, Vera P. and Pavlović, Vladimir B. and Vlahović, Branislav",
year = "2023",
abstract = "Barium titanate (BT) perovskite particles were surface modified by means of mechanical treatment and used as inorganic component in polyvinylidene fluoride (PVDF) based composites. The changes in electrical properties of the composite films with increasing in filler content were followed by dielectric spectroscopy, breakdown strength and D-E measurements. A comparison of the properties of the composites prepared with untreated and mechanically activated particles revealed that there is a significant difference in their performances at low filler concentrations (<20 wt%). Introduction of the surface modified ceramic particles into PVDF matrix led to an increase of the dielectric constant without affecting significantly the electrical breakdown strength. In contrast, when as received BT particles were used a filler, both dielectric constants and breakdown strengths of the composite films were lower than the corresponding values observed for the pure PVDF. At higher concentrations, however, the influence of pre-treatment of the filler on the effective electrical properties becomes less significant. The obtained results were discussed in terms of the pronounced crystallization of polar β and γ crystal phases of PVDF in the presence of surface modified BT fillers, which is confirmed by Raman spectroscopy.",
publisher = "IOP Publishing Ltd",
journal = "Physica Scripta",
title = "Toward improved PVDF-BaTiO3 composite dielectrics: mechanical activation of the filler versus filler content",
number = "11",
pages = "115932",
volume = "98",
doi = "10.1088/1402-4896/acff4d"
}

Djoković, V., Dudić, D., Dojčilović, R., Marinković, F., Pavlović, V. P., Pavlović, V. B.,& Vlahović, B.. (2023). Toward improved PVDF-BaTiO3 composite dielectrics: mechanical activation of the filler versus filler content. in Physica Scripta
IOP Publishing Ltd., 98(11), 115932.
https://doi.org/10.1088/1402-4896/acff4d

Djoković V, Dudić D, Dojčilović R, Marinković F, Pavlović VP, Pavlović VB, Vlahović B. Toward improved PVDF-BaTiO3 composite dielectrics: mechanical activation of the filler versus filler content. in Physica Scripta. 2023;98(11):115932.
doi:10.1088/1402-4896/acff4d .

Djoković, Vladimir, Dudić, Duško, Dojčilović, Radovan, Marinković, Filip, Pavlović, Vera P., Pavlović, Vladimir B., Vlahović, Branislav, "Toward improved PVDF-BaTiO3 composite dielectrics: mechanical activation of the filler versus filler content" in Physica Scripta, 98, no. 11 (2023):115932,
https://doi.org/10.1088/1402-4896/acff4d . .

TY  - JOUR
AU  - Lučić, Milica
AU  - Potkonjak, Nebojša
AU  - Sredović Ignjatović, Ivana
AU  - Lević, Steva
AU  - Dajić-Stevanović, Zora
AU  - Kolašinac, Stefan
AU  - Belović, Miona
AU  - Torbica, Aleksandra
AU  - Zlatanović, Ivan
AU  - Pavlović, Vladimir
AU  - Onjia, Antonije
PY  - 2023
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/6887
AB  - This study investigates the effects of ultrasound, in combination with chemical pretreatments, on the quality attributes (total phenolic and carotenoid content, antioxidant activity
(2,2-Diphenyl-1-picrylhydrazyl assay (DPPH)), ferric-reducing ability (FRAP), CIE L* a* b* color,
non-enzymatic browning, rehydration ratio, textural and morphological properties) of red pepper
subjected to drying (hot air drying or freeze drying). The fractional factorial design was used to
assess the impact of factors. The global Derringer desirability function was used to determine the
optimal conditions for the best quality attributes of dried pepper. The drying method influenced total
phenolic content, a* (redness), and initial rehydration ratio; pretreatment time significantly affected
FRAP antiradical activity, a*, chroma and non-browning index, while pH-value had a significant
effect on the texture of dried pepper. Non-enzymatic browning was reduced to 72.6%, while the
DPPH antioxidant capacity of freeze-dried peppers was enhanced from 4.2% to 71.9%. Ultrasonic
pretreatment led to changes in the pepper morphology, while potassium metabisulfite (KMS) was a
more effective additive than citric acid.
PB  - MDPI
T2  - Foods
T1  - Influence of Ultrasonic and Chemical Pretreatments on Quality Attributes of Dried Pepper (Capsicum annuum)
IS  - 13
SP  - 2468
VL  - 12
DO  - 10.3390/foods12132468
ER  - 

@article{
author = "Lučić, Milica and Potkonjak, Nebojša and Sredović Ignjatović, Ivana and Lević, Steva and Dajić-Stevanović, Zora and Kolašinac, Stefan and Belović, Miona and Torbica, Aleksandra and Zlatanović, Ivan and Pavlović, Vladimir and Onjia, Antonije",
year = "2023",
abstract = "This study investigates the effects of ultrasound, in combination with chemical pretreatments, on the quality attributes (total phenolic and carotenoid content, antioxidant activity
(2,2-Diphenyl-1-picrylhydrazyl assay (DPPH)), ferric-reducing ability (FRAP), CIE L* a* b* color,
non-enzymatic browning, rehydration ratio, textural and morphological properties) of red pepper
subjected to drying (hot air drying or freeze drying). The fractional factorial design was used to
assess the impact of factors. The global Derringer desirability function was used to determine the
optimal conditions for the best quality attributes of dried pepper. The drying method influenced total
phenolic content, a* (redness), and initial rehydration ratio; pretreatment time significantly affected
FRAP antiradical activity, a*, chroma and non-browning index, while pH-value had a significant
effect on the texture of dried pepper. Non-enzymatic browning was reduced to 72.6%, while the
DPPH antioxidant capacity of freeze-dried peppers was enhanced from 4.2% to 71.9%. Ultrasonic
pretreatment led to changes in the pepper morphology, while potassium metabisulfite (KMS) was a
more effective additive than citric acid.",
publisher = "MDPI",
journal = "Foods",
title = "Influence of Ultrasonic and Chemical Pretreatments on Quality Attributes of Dried Pepper (Capsicum annuum)",
number = "13",
pages = "2468",
volume = "12",
doi = "10.3390/foods12132468"
}

Lučić, M., Potkonjak, N., Sredović Ignjatović, I., Lević, S., Dajić-Stevanović, Z., Kolašinac, S., Belović, M., Torbica, A., Zlatanović, I., Pavlović, V.,& Onjia, A.. (2023). Influence of Ultrasonic and Chemical Pretreatments on Quality Attributes of Dried Pepper (Capsicum annuum). in Foods
MDPI., 12(13), 2468.
https://doi.org/10.3390/foods12132468

Lučić M, Potkonjak N, Sredović Ignjatović I, Lević S, Dajić-Stevanović Z, Kolašinac S, Belović M, Torbica A, Zlatanović I, Pavlović V, Onjia A. Influence of Ultrasonic and Chemical Pretreatments on Quality Attributes of Dried Pepper (Capsicum annuum). in Foods. 2023;12(13):2468.
doi:10.3390/foods12132468 .

Lučić, Milica, Potkonjak, Nebojša, Sredović Ignjatović, Ivana, Lević, Steva, Dajić-Stevanović, Zora, Kolašinac, Stefan, Belović, Miona, Torbica, Aleksandra, Zlatanović, Ivan, Pavlović, Vladimir, Onjia, Antonije, "Influence of Ultrasonic and Chemical Pretreatments on Quality Attributes of Dried Pepper (Capsicum annuum)" in Foods, 12, no. 13 (2023):2468,
https://doi.org/10.3390/foods12132468 . .

TY  - JOUR
AU  - Vujančević, Jelena
AU  - Andričević, Pavao
AU  - Đokić, Veljko
AU  - Blagojević, Vladimir A.
AU  - Pavlović, Vera P.
AU  - Ćirković, Jovana
AU  - Horvath, Endre
AU  - Forro, Laszlo
AU  - Karoui, Abdennaceur
AU  - Pavlović, Vladimir B.
AU  - Janaćković, Đorđe
PY  - 2023
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/6323
AB  - In this study, we report the influence of vanadium oxide (VO), as a photosensitive component, on the photoactivity of TiO2 nanotubes (TNTs). A series of TNTs of varying tube diameter were synthesized by the anodization of titanium foils at different voltages, while vanadium oxide was deposited on TNTs by wet chemical deposition. An improvement in the optical properties of nanotubes was observed after the deposition of vanadium oxide. An improvement in the optical properties (redshift in UV-Vis spectra) of TNTs and TNT/VO was noted. The photocatalytic activity was improved with increasing tube diameter, while it was weakened after the deposition of VO. Furthermore, photoactivity was investigated in photodiodes based on TNTs or TNT/VO and single crystals of CH3NH3PbI3. The photoelectric measurement revealed that different TNT diameters did not influence the I-V characteristic of the photodiodes, while the deposition of VO improved the photocurrent for smaller TNTs.
PB  - MDPI
T2  - Catalysts
T1  - Effect of the Deposition of Vanadium-Oxide on the Photocatalytic Activity of TiO2 Nanotubes and Its Photodiode Performance Interfaced with CH3NH3PbI3 Single Crystal
IS  - 2
SP  - 352
VL  - 13
DO  - 10.3390/catal13020352
ER  - 

@article{
author = "Vujančević, Jelena and Andričević, Pavao and Đokić, Veljko and Blagojević, Vladimir A. and Pavlović, Vera P. and Ćirković, Jovana and Horvath, Endre and Forro, Laszlo and Karoui, Abdennaceur and Pavlović, Vladimir B. and Janaćković, Đorđe",
year = "2023",
abstract = "In this study, we report the influence of vanadium oxide (VO), as a photosensitive component, on the photoactivity of TiO2 nanotubes (TNTs). A series of TNTs of varying tube diameter were synthesized by the anodization of titanium foils at different voltages, while vanadium oxide was deposited on TNTs by wet chemical deposition. An improvement in the optical properties of nanotubes was observed after the deposition of vanadium oxide. An improvement in the optical properties (redshift in UV-Vis spectra) of TNTs and TNT/VO was noted. The photocatalytic activity was improved with increasing tube diameter, while it was weakened after the deposition of VO. Furthermore, photoactivity was investigated in photodiodes based on TNTs or TNT/VO and single crystals of CH3NH3PbI3. The photoelectric measurement revealed that different TNT diameters did not influence the I-V characteristic of the photodiodes, while the deposition of VO improved the photocurrent for smaller TNTs.",
publisher = "MDPI",
journal = "Catalysts",
title = "Effect of the Deposition of Vanadium-Oxide on the Photocatalytic Activity of TiO2 Nanotubes and Its Photodiode Performance Interfaced with CH3NH3PbI3 Single Crystal",
number = "2",
pages = "352",
volume = "13",
doi = "10.3390/catal13020352"
}

Vujančević, J., Andričević, P., Đokić, V., Blagojević, V. A., Pavlović, V. P., Ćirković, J., Horvath, E., Forro, L., Karoui, A., Pavlović, V. B.,& Janaćković, Đ.. (2023). Effect of the Deposition of Vanadium-Oxide on the Photocatalytic Activity of TiO2 Nanotubes and Its Photodiode Performance Interfaced with CH3NH3PbI3 Single Crystal. in Catalysts
MDPI., 13(2), 352.
https://doi.org/10.3390/catal13020352

Vujančević J, Andričević P, Đokić V, Blagojević VA, Pavlović VP, Ćirković J, Horvath E, Forro L, Karoui A, Pavlović VB, Janaćković Đ. Effect of the Deposition of Vanadium-Oxide on the Photocatalytic Activity of TiO2 Nanotubes and Its Photodiode Performance Interfaced with CH3NH3PbI3 Single Crystal. in Catalysts. 2023;13(2):352.
doi:10.3390/catal13020352 .

Vujančević, Jelena, Andričević, Pavao, Đokić, Veljko, Blagojević, Vladimir A., Pavlović, Vera P., Ćirković, Jovana, Horvath, Endre, Forro, Laszlo, Karoui, Abdennaceur, Pavlović, Vladimir B., Janaćković, Đorđe, "Effect of the Deposition of Vanadium-Oxide on the Photocatalytic Activity of TiO2 Nanotubes and Its Photodiode Performance Interfaced with CH3NH3PbI3 Single Crystal" in Catalysts, 13, no. 2 (2023):352,
https://doi.org/10.3390/catal13020352 . .

TY  - CONF
AU  - Pavlović, Vladimir B.
AU  - Milosavljević, Nataša
AU  - Pavlović, Vera P.
AU  - Vlahović, Branislav
PY  - 2023
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/7311
AB  - COVID-19 pandemic quickly evolved from health crisis into an economic, cultural and social crisis. According to International Association of Universities global survey report, many universities already for see the impacts of economic crisis on students and their families, face the closure for short, medium or long term, while social distancing measurements urge universities to develop e-courses and to move towards ”emergency online education”. In order to provide access for all students to global virtual educational environment, with differentiated and individualized learning tools, we focus on cooperation for innovation in digitally-supported education, the exchange of good practices teaching/learning experiences in the field sof web-based education and capacity building by creating the laboratory for Artificial Intelligence (AI), heuristics and bioinformatics at the University of Belgrade-Faculty of Agriculture. The main idea is to create eEDUCANeT platform for students and academic staff for pedagogical use of digital technologies and AI in teaching, learning and research.
PB  - Berlin, Boston: De Gruyter, 2023
C3  - Mathematics for Human Flourishing in the Time of COVID-19 and Post COVID-19: Proceedings of the Workshop held at the Faculty of Mechanical Engineering, University of Niš, Niš, 21 of October 2020
T1  - Artificial intelligence and digital technologies in digitally-supported university education
EP  - 202
SP  - 195
DO  - 10.1515/9783110734119-017
ER  - 

@conference{
author = "Pavlović, Vladimir B. and Milosavljević, Nataša and Pavlović, Vera P. and Vlahović, Branislav",
year = "2023",
abstract = "COVID-19 pandemic quickly evolved from health crisis into an economic, cultural and social crisis. According to International Association of Universities global survey report, many universities already for see the impacts of economic crisis on students and their families, face the closure for short, medium or long term, while social distancing measurements urge universities to develop e-courses and to move towards ”emergency online education”. In order to provide access for all students to global virtual educational environment, with differentiated and individualized learning tools, we focus on cooperation for innovation in digitally-supported education, the exchange of good practices teaching/learning experiences in the field sof web-based education and capacity building by creating the laboratory for Artificial Intelligence (AI), heuristics and bioinformatics at the University of Belgrade-Faculty of Agriculture. The main idea is to create eEDUCANeT platform for students and academic staff for pedagogical use of digital technologies and AI in teaching, learning and research.",
publisher = "Berlin, Boston: De Gruyter, 2023",
journal = "Mathematics for Human Flourishing in the Time of COVID-19 and Post COVID-19: Proceedings of the Workshop held at the Faculty of Mechanical Engineering, University of Niš, Niš, 21 of October 2020",
title = "Artificial intelligence and digital technologies in digitally-supported university education",
pages = "202-195",
doi = "10.1515/9783110734119-017"
}

Pavlović, V. B., Milosavljević, N., Pavlović, V. P.,& Vlahović, B.. (2023). Artificial intelligence and digital technologies in digitally-supported university education. in Mathematics for Human Flourishing in the Time of COVID-19 and Post COVID-19: Proceedings of the Workshop held at the Faculty of Mechanical Engineering, University of Niš, Niš, 21 of October 2020
Berlin, Boston: De Gruyter, 2023., 195-202.
https://doi.org/10.1515/9783110734119-017

Pavlović VB, Milosavljević N, Pavlović VP, Vlahović B. Artificial intelligence and digital technologies in digitally-supported university education. in Mathematics for Human Flourishing in the Time of COVID-19 and Post COVID-19: Proceedings of the Workshop held at the Faculty of Mechanical Engineering, University of Niš, Niš, 21 of October 2020. 2023;:195-202.
doi:10.1515/9783110734119-017 .

Pavlović, Vladimir B., Milosavljević, Nataša, Pavlović, Vera P., Vlahović, Branislav, "Artificial intelligence and digital technologies in digitally-supported university education" in Mathematics for Human Flourishing in the Time of COVID-19 and Post COVID-19: Proceedings of the Workshop held at the Faculty of Mechanical Engineering, University of Niš, Niš, 21 of October 2020 (2023):195-202,
https://doi.org/10.1515/9783110734119-017 . .

TY  - JOUR
AU  - Salih, Rabab
AU  - Veličković, Zlate
AU  - Milošević, Milena
AU  - Pavlović, Vera P.
AU  - Cvijetić, Ilija
AU  - Sofrenić, Ivana V.
AU  - Gržetić, Jelena D.
AU  - Marinković, Aleksandar
PY  - 2023
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/3952
AB  - Multifunctional lignin bio-based adsorbent, b-LMS, was obtained via inverse copolymerization in the suspension of acryloyl modified kraft lignin (KfL-AA) and bio-based trimethylolpropane triacrylate (bio-TMPTA). Morphological and structural characterization of KfL-AA and b-LMS was performed using BET, FTIR, Raman, NMR, TGA, SEM, and XPS techniques. The b-LMS microspheres with 253 ± 42 μm diameters, 69.4 m2 g−1 surface area, and 59% porosity efficiently adsorb Malachite Green (MG), Tartrazine (T), and Methyl Red (MR) dye. The influence of pH, pollutant concentration, temperature, and time on the removal efficiency was studied in a batch mode. Favorable and spontaneous processes with high adsorption capacities e.g. 116.8 mg g−1 for MG, 86.8 mg g−1 for T, and 68.6 mg g−1 for MR indicate the significant adsorptive potential of b-LMS. Results from diffusional and single mass transfer resistance studies indicate that pore diffusion is a rate-limiting step. Theoretical calculations confirmed a higher affinity of b-LMS to cationic dye MG compared with an anionic and neutral one, i.e. T and MR, respectively. The data fitting from a flow system, using semi-empirical equations and Pore Surface Diffusion Modelling (PSDM) provided breakthrough point determination. The results from the desorption and competitive adsorption study proved the exceptional performance of b-LMS. Moreover, sulfation of b-LMS, i.e.production of b-LMS-OSO3H, introduced high-affinity sulfate groups with respect to cationic dye and cations. Developed methodology implements the principle of sustainable development and offers concept whose results contribute to the minimization of environmental pollution.
PB  - Elsevier
T2  - Journal of Environmental Management
T1  - Lignin based microspheres for effective dyes removal: Design, synthesis and adsorption mechanism supported with theoretical study
IS  - January
SP  - 116838
VL  - 326
DO  - 10.1016/j.jenvman.2022.116838
ER  - 

@article{
author = "Salih, Rabab and Veličković, Zlate and Milošević, Milena and Pavlović, Vera P. and Cvijetić, Ilija and Sofrenić, Ivana V. and Gržetić, Jelena D. and Marinković, Aleksandar",
year = "2023",
abstract = "Multifunctional lignin bio-based adsorbent, b-LMS, was obtained via inverse copolymerization in the suspension of acryloyl modified kraft lignin (KfL-AA) and bio-based trimethylolpropane triacrylate (bio-TMPTA). Morphological and structural characterization of KfL-AA and b-LMS was performed using BET, FTIR, Raman, NMR, TGA, SEM, and XPS techniques. The b-LMS microspheres with 253 ± 42 μm diameters, 69.4 m2 g−1 surface area, and 59% porosity efficiently adsorb Malachite Green (MG), Tartrazine (T), and Methyl Red (MR) dye. The influence of pH, pollutant concentration, temperature, and time on the removal efficiency was studied in a batch mode. Favorable and spontaneous processes with high adsorption capacities e.g. 116.8 mg g−1 for MG, 86.8 mg g−1 for T, and 68.6 mg g−1 for MR indicate the significant adsorptive potential of b-LMS. Results from diffusional and single mass transfer resistance studies indicate that pore diffusion is a rate-limiting step. Theoretical calculations confirmed a higher affinity of b-LMS to cationic dye MG compared with an anionic and neutral one, i.e. T and MR, respectively. The data fitting from a flow system, using semi-empirical equations and Pore Surface Diffusion Modelling (PSDM) provided breakthrough point determination. The results from the desorption and competitive adsorption study proved the exceptional performance of b-LMS. Moreover, sulfation of b-LMS, i.e.production of b-LMS-OSO3H, introduced high-affinity sulfate groups with respect to cationic dye and cations. Developed methodology implements the principle of sustainable development and offers concept whose results contribute to the minimization of environmental pollution.",
publisher = "Elsevier",
journal = "Journal of Environmental Management",
title = "Lignin based microspheres for effective dyes removal: Design, synthesis and adsorption mechanism supported with theoretical study",
number = "January",
pages = "116838",
volume = "326",
doi = "10.1016/j.jenvman.2022.116838"
}

Salih, R., Veličković, Z., Milošević, M., Pavlović, V. P., Cvijetić, I., Sofrenić, I. V., Gržetić, J. D.,& Marinković, A.. (2023). Lignin based microspheres for effective dyes removal: Design, synthesis and adsorption mechanism supported with theoretical study. in Journal of Environmental Management
Elsevier., 326(January), 116838.
https://doi.org/10.1016/j.jenvman.2022.116838

Salih R, Veličković Z, Milošević M, Pavlović VP, Cvijetić I, Sofrenić IV, Gržetić JD, Marinković A. Lignin based microspheres for effective dyes removal: Design, synthesis and adsorption mechanism supported with theoretical study. in Journal of Environmental Management. 2023;326(January):116838.
doi:10.1016/j.jenvman.2022.116838 .

Salih, Rabab, Veličković, Zlate, Milošević, Milena, Pavlović, Vera P., Cvijetić, Ilija, Sofrenić, Ivana V., Gržetić, Jelena D., Marinković, Aleksandar, "Lignin based microspheres for effective dyes removal: Design, synthesis and adsorption mechanism supported with theoretical study" in Journal of Environmental Management, 326, no. January (2023):116838,
https://doi.org/10.1016/j.jenvman.2022.116838 . .

TY  - JOUR
AU  - Salih, Rabab
AU  - Veličković, Zlate
AU  - Milošević, Milena
AU  - Pavlović, Vera P.
AU  - Cvijetić, Ilija
AU  - Sofrenić, Ivana V.
AU  - Gržetić, Jelena D.
AU  - Marinković, Aleksandar
PY  - 2023
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/7310
AB  - Multifunctional lignin bio-based adsorbent, b-LMS, was obtained via inverse copolymerization in the suspension of acryloyl modified kraft lignin (KfL-AA) and bio-based trimethylolpropane triacrylate (bio-TMPTA). Morphological and structural characterization of KfL-AA and b-LMS was performed using BET, FTIR, Raman, NMR, TGA, SEM, and XPS techniques. The b-LMS microspheres with 253 ± 42 μm diameters, 69.4 m2 g−1 surface area, and 59% porosity efficiently adsorb Malachite Green (MG), Tartrazine (T), and Methyl Red (MR) dye. The influence of pH, pollutant concentration, temperature, and time on the removal efficiency was studied in a batch mode. Favorable and spontaneous processes with high adsorption capacities e.g. 116.8 mg g−1 for MG, 86.8 mg g−1 for T, and 68.6 mg g−1 for MR indicate the significant adsorptive potential of b-LMS. Results from diffusional and single mass transfer resistance studies indicate that pore diffusion is a rate-limiting step. Theoretical calculations confirmed a higher affinity of b-LMS to cationic dye MG compared with an anionic and neutral one, i.e. T and MR, respectively. The data fitting from a flow system, using semi-empirical equations and Pore Surface Diffusion Modelling (PSDM) provided breakthrough point determination. The results from the desorption and competitive adsorption study proved the exceptional performance of b-LMS. Moreover, sulfation of b-LMS, i.e.production of b-LMS-OSO3H, introduced high-affinity sulfate groups with respect to cationic dye and cations. Developed methodology implements the principle of sustainable development and offers concept whose results contribute to the minimization of environmental pollution.
PB  - Elsevier
T2  - Journal of Environmental Management
T1  - Lignin based microspheres for effective dyes removal: Design, synthesis and adsorption mechanism supported with theoretical study
SP  - 116838
VL  - 326
DO  - 10.1016/j.jenvman.2022.116838
ER  - 

@article{
author = "Salih, Rabab and Veličković, Zlate and Milošević, Milena and Pavlović, Vera P. and Cvijetić, Ilija and Sofrenić, Ivana V. and Gržetić, Jelena D. and Marinković, Aleksandar",
year = "2023",
abstract = "Multifunctional lignin bio-based adsorbent, b-LMS, was obtained via inverse copolymerization in the suspension of acryloyl modified kraft lignin (KfL-AA) and bio-based trimethylolpropane triacrylate (bio-TMPTA). Morphological and structural characterization of KfL-AA and b-LMS was performed using BET, FTIR, Raman, NMR, TGA, SEM, and XPS techniques. The b-LMS microspheres with 253 ± 42 μm diameters, 69.4 m2 g−1 surface area, and 59% porosity efficiently adsorb Malachite Green (MG), Tartrazine (T), and Methyl Red (MR) dye. The influence of pH, pollutant concentration, temperature, and time on the removal efficiency was studied in a batch mode. Favorable and spontaneous processes with high adsorption capacities e.g. 116.8 mg g−1 for MG, 86.8 mg g−1 for T, and 68.6 mg g−1 for MR indicate the significant adsorptive potential of b-LMS. Results from diffusional and single mass transfer resistance studies indicate that pore diffusion is a rate-limiting step. Theoretical calculations confirmed a higher affinity of b-LMS to cationic dye MG compared with an anionic and neutral one, i.e. T and MR, respectively. The data fitting from a flow system, using semi-empirical equations and Pore Surface Diffusion Modelling (PSDM) provided breakthrough point determination. The results from the desorption and competitive adsorption study proved the exceptional performance of b-LMS. Moreover, sulfation of b-LMS, i.e.production of b-LMS-OSO3H, introduced high-affinity sulfate groups with respect to cationic dye and cations. Developed methodology implements the principle of sustainable development and offers concept whose results contribute to the minimization of environmental pollution.",
publisher = "Elsevier",
journal = "Journal of Environmental Management",
title = "Lignin based microspheres for effective dyes removal: Design, synthesis and adsorption mechanism supported with theoretical study",
pages = "116838",
volume = "326",
doi = "10.1016/j.jenvman.2022.116838"
}

Salih, R., Veličković, Z., Milošević, M., Pavlović, V. P., Cvijetić, I., Sofrenić, I. V., Gržetić, J. D.,& Marinković, A.. (2023). Lignin based microspheres for effective dyes removal: Design, synthesis and adsorption mechanism supported with theoretical study. in Journal of Environmental Management
Elsevier., 326, 116838.
https://doi.org/10.1016/j.jenvman.2022.116838

Salih R, Veličković Z, Milošević M, Pavlović VP, Cvijetić I, Sofrenić IV, Gržetić JD, Marinković A. Lignin based microspheres for effective dyes removal: Design, synthesis and adsorption mechanism supported with theoretical study. in Journal of Environmental Management. 2023;326:116838.
doi:10.1016/j.jenvman.2022.116838 .

Salih, Rabab, Veličković, Zlate, Milošević, Milena, Pavlović, Vera P., Cvijetić, Ilija, Sofrenić, Ivana V., Gržetić, Jelena D., Marinković, Aleksandar, "Lignin based microspheres for effective dyes removal: Design, synthesis and adsorption mechanism supported with theoretical study" in Journal of Environmental Management, 326 (2023):116838,
https://doi.org/10.1016/j.jenvman.2022.116838 . .

TY  - JOUR
AU  - Djoković, Vladimir
AU  - Dudić, Duško
AU  - Dojčilović, Radovan
AU  - Marinković, Filip
AU  - Pavlović, Vera P.
AU  - Pavlović, Vladimir B.
AU  - Vlahović, Branislav
PY  - 2023
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/7071
AB  - Barium titanate (BT) perovskite particles were surface modified by means of mechanical treatment and used as inorganic component in polyvinylidene fluoride (PVDF) based composites. The changes in electrical properties of the composite films with increasing in filler content were followed by dielectric spectroscopy, breakdown strength and D-E measurements. A comparison of the properties of the composites prepared with untreated and mechanically activated particles revealed that there is a significant difference in their performances at low filler concentrations (<20 wt%). Introduction of the surface modified ceramic particles into PVDF matrix led to an increase of the dielectric constant without affecting significantly the electrical breakdown strength. In contrast, when as received BT particles were used a filler, both dielectric constants and breakdown strengths of the composite films were lower than the corresponding values observed for the pure PVDF. At higher concentrations, however, the influence of pre-treatment of the filler on the effective electrical properties becomes less significant. The obtained results were discussed in terms of the pronounced crystallization of polar β and γ crystal phases of PVDF in the presence of surface modified BT fillers, which is confirmed by Raman spectroscopy.
PB  - IOP Publishing Ltd
T2  - Physica Scripta
T1  - Toward improved PVDF-BaTiO3 composite dielectrics: mechanical activation of the filler versus filler content
IS  - 11
SP  - 115932
VL  - 98
DO  - 10.1088/1402-4896/acff4d
ER  - 

@article{
author = "Djoković, Vladimir and Dudić, Duško and Dojčilović, Radovan and Marinković, Filip and Pavlović, Vera P. and Pavlović, Vladimir B. and Vlahović, Branislav",
year = "2023",
abstract = "Barium titanate (BT) perovskite particles were surface modified by means of mechanical treatment and used as inorganic component in polyvinylidene fluoride (PVDF) based composites. The changes in electrical properties of the composite films with increasing in filler content were followed by dielectric spectroscopy, breakdown strength and D-E measurements. A comparison of the properties of the composites prepared with untreated and mechanically activated particles revealed that there is a significant difference in their performances at low filler concentrations (<20 wt%). Introduction of the surface modified ceramic particles into PVDF matrix led to an increase of the dielectric constant without affecting significantly the electrical breakdown strength. In contrast, when as received BT particles were used a filler, both dielectric constants and breakdown strengths of the composite films were lower than the corresponding values observed for the pure PVDF. At higher concentrations, however, the influence of pre-treatment of the filler on the effective electrical properties becomes less significant. The obtained results were discussed in terms of the pronounced crystallization of polar β and γ crystal phases of PVDF in the presence of surface modified BT fillers, which is confirmed by Raman spectroscopy.",
publisher = "IOP Publishing Ltd",
journal = "Physica Scripta",
title = "Toward improved PVDF-BaTiO3 composite dielectrics: mechanical activation of the filler versus filler content",
number = "11",
pages = "115932",
volume = "98",
doi = "10.1088/1402-4896/acff4d"
}

Djoković, V., Dudić, D., Dojčilović, R., Marinković, F., Pavlović, V. P., Pavlović, V. B.,& Vlahović, B.. (2023). Toward improved PVDF-BaTiO3 composite dielectrics: mechanical activation of the filler versus filler content. in Physica Scripta
IOP Publishing Ltd., 98(11), 115932.
https://doi.org/10.1088/1402-4896/acff4d

Djoković V, Dudić D, Dojčilović R, Marinković F, Pavlović VP, Pavlović VB, Vlahović B. Toward improved PVDF-BaTiO3 composite dielectrics: mechanical activation of the filler versus filler content. in Physica Scripta. 2023;98(11):115932.
doi:10.1088/1402-4896/acff4d .

Djoković, Vladimir, Dudić, Duško, Dojčilović, Radovan, Marinković, Filip, Pavlović, Vera P., Pavlović, Vladimir B., Vlahović, Branislav, "Toward improved PVDF-BaTiO3 composite dielectrics: mechanical activation of the filler versus filler content" in Physica Scripta, 98, no. 11 (2023):115932,
https://doi.org/10.1088/1402-4896/acff4d . .

TY  - JOUR
AU  - Janićijević, Aleksandra
AU  - Pavlović, Vera P.
AU  - Kovačević, Danijela
AU  - Perić, Marko
AU  - Vlahović, Branislav
AU  - Pavlović, Vladimir B.
AU  - Filipović, Suzana
PY  - 2022
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/3689
AB  - The rise of innovation in the electrical industry is driven by the controlled design of new materials. The hybrid materials based on magnetite/nanocellulose are highly interesting due to their various applications in medicine, ecology, catalysis and electronics. In this study, the structure and morphology of nanocellulose/magnetite hybrid nanomaterials were investigated. The effect of nanocellulose loading on the crystal structure of synthesized composites was investigated by XRD and FTIR methods. The presented study reveals that the interaction between the cellulose and magnetic nanoparticles depends on the nanocellulose content. Further, a transition from cellulose II to cellulose I allomorph is observed. SEM and EDS are employed to determine the variation in morphology with changes in component concentrations. By the calculation of magnetic interactions between adjacent Fe3+ and Fe2+ ions within composites, it is determined that ferromagnetic coupling predominates.
PB  - MDPI, Basel
T2  - Polymers
T1  - Structural Characterization of Nanocellulose/Fe3O4 Hybrid Nanomaterials
IS  - 9
SP  - 1819
VL  - 14
DO  - 10.3390/polym14091819
ER  - 

@article{
author = "Janićijević, Aleksandra and Pavlović, Vera P. and Kovačević, Danijela and Perić, Marko and Vlahović, Branislav and Pavlović, Vladimir B. and Filipović, Suzana",
year = "2022",
abstract = "The rise of innovation in the electrical industry is driven by the controlled design of new materials. The hybrid materials based on magnetite/nanocellulose are highly interesting due to their various applications in medicine, ecology, catalysis and electronics. In this study, the structure and morphology of nanocellulose/magnetite hybrid nanomaterials were investigated. The effect of nanocellulose loading on the crystal structure of synthesized composites was investigated by XRD and FTIR methods. The presented study reveals that the interaction between the cellulose and magnetic nanoparticles depends on the nanocellulose content. Further, a transition from cellulose II to cellulose I allomorph is observed. SEM and EDS are employed to determine the variation in morphology with changes in component concentrations. By the calculation of magnetic interactions between adjacent Fe3+ and Fe2+ ions within composites, it is determined that ferromagnetic coupling predominates.",
publisher = "MDPI, Basel",
journal = "Polymers",
title = "Structural Characterization of Nanocellulose/Fe3O4 Hybrid Nanomaterials",
number = "9",
pages = "1819",
volume = "14",
doi = "10.3390/polym14091819"
}

Janićijević, A., Pavlović, V. P., Kovačević, D., Perić, M., Vlahović, B., Pavlović, V. B.,& Filipović, S.. (2022). Structural Characterization of Nanocellulose/Fe3O4 Hybrid Nanomaterials. in Polymers
MDPI, Basel., 14(9), 1819.
https://doi.org/10.3390/polym14091819

Janićijević A, Pavlović VP, Kovačević D, Perić M, Vlahović B, Pavlović VB, Filipović S. Structural Characterization of Nanocellulose/Fe3O4 Hybrid Nanomaterials. in Polymers. 2022;14(9):1819.
doi:10.3390/polym14091819 .

Janićijević, Aleksandra, Pavlović, Vera P., Kovačević, Danijela, Perić, Marko, Vlahović, Branislav, Pavlović, Vladimir B., Filipović, Suzana, "Structural Characterization of Nanocellulose/Fe3O4 Hybrid Nanomaterials" in Polymers, 14, no. 9 (2022):1819,
https://doi.org/10.3390/polym14091819 . .

TY  - JOUR
AU  - Đukić, Dunja
AU  - Šuljagić, Marija
AU  - Anđelković, Ljubica
AU  - Pavlović, Vera P.
AU  - Bučevac, Dušan
AU  - Vrbica, Boško
AU  - Mirković, Miljana
PY  - 2022
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/4064
AB  - The effect of Ca2+ amount and sintering temperature on mechanical properties of geopolymer-brushite (GPB) binders was investigated. Brushite and raw abandoned kaolinite clay thermally transformed into metakaolin were used for GPB synthesis. The complete phase and structural analyses were performed by X-ray powder diffraction, and Fourier transforms infrared spectroscopy (FT-IR). The pore-filling effect as a consequence of Ca2+ ions incorporation into the hybrid geopolymer networks improved the compressive strength. On the other hand, the chosen biscuit sintering at 800 and 900oC caused the phase transformation of brushite into calcium pyrophosphate, which negatively affected the compressive strength of such materials. The obtained results indicate that the usage of relatively high sintering temperatures is not always the necessary step for producing geopolymer-based types of cement with prominent mechanical properties.
PB  - ETRAN
T2  - Science of Sintering
T1  - Effect of Sintering Temperature and Calcium amount on Compressive Strength of Brushite-Metakaolin Polymer Materials
EP  - 294
IS  - 3
SP  - 287
VL  - 54
DO  - 10.2298/SOS2203287D
ER  - 

@article{
author = "Đukić, Dunja and Šuljagić, Marija and Anđelković, Ljubica and Pavlović, Vera P. and Bučevac, Dušan and Vrbica, Boško and Mirković, Miljana",
year = "2022",
abstract = "The effect of Ca2+ amount and sintering temperature on mechanical properties of geopolymer-brushite (GPB) binders was investigated. Brushite and raw abandoned kaolinite clay thermally transformed into metakaolin were used for GPB synthesis. The complete phase and structural analyses were performed by X-ray powder diffraction, and Fourier transforms infrared spectroscopy (FT-IR). The pore-filling effect as a consequence of Ca2+ ions incorporation into the hybrid geopolymer networks improved the compressive strength. On the other hand, the chosen biscuit sintering at 800 and 900oC caused the phase transformation of brushite into calcium pyrophosphate, which negatively affected the compressive strength of such materials. The obtained results indicate that the usage of relatively high sintering temperatures is not always the necessary step for producing geopolymer-based types of cement with prominent mechanical properties.",
publisher = "ETRAN",
journal = "Science of Sintering",
title = "Effect of Sintering Temperature and Calcium amount on Compressive Strength of Brushite-Metakaolin Polymer Materials",
pages = "294-287",
number = "3",
volume = "54",
doi = "10.2298/SOS2203287D"
}

Đukić, D., Šuljagić, M., Anđelković, L., Pavlović, V. P., Bučevac, D., Vrbica, B.,& Mirković, M.. (2022). Effect of Sintering Temperature and Calcium amount on Compressive Strength of Brushite-Metakaolin Polymer Materials. in Science of Sintering
ETRAN., 54(3), 287-294.
https://doi.org/10.2298/SOS2203287D

Đukić D, Šuljagić M, Anđelković L, Pavlović VP, Bučevac D, Vrbica B, Mirković M. Effect of Sintering Temperature and Calcium amount on Compressive Strength of Brushite-Metakaolin Polymer Materials. in Science of Sintering. 2022;54(3):287-294.
doi:10.2298/SOS2203287D .

Đukić, Dunja, Šuljagić, Marija, Anđelković, Ljubica, Pavlović, Vera P., Bučevac, Dušan, Vrbica, Boško, Mirković, Miljana, "Effect of Sintering Temperature and Calcium amount on Compressive Strength of Brushite-Metakaolin Polymer Materials" in Science of Sintering, 54, no. 3 (2022):287-294,
https://doi.org/10.2298/SOS2203287D . .

TY  - CONF
AU  - Vujančević, Jelena
AU  - Blagojević, Vladimir A.
AU  - Andričević, Pavao
AU  - Pavlović, Vera P.
AU  - Horvath, Endre
AU  - Forro, Laszlo
AU  - Vlahović, Branislav
AU  - Pavlović, Vladimir B.
AU  - Janaćković, Đorđe
PY  - 2022
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/4226
AB  - The aim of this study was to investigate the influence of the deposition of vanadium oxide epitaxial layer on the photoresponse of TiO2/CH3NH3PbI3 heterojunction. TiO2 nanotube array was synthesized via anodization of titanium foil at three different voltages. After annealing at 450 °C, vanadium oxide was deposited by direct deposition from vanadyl(IV) sulfate solution. Microstructure analysis has been used for the investigation of the influence of different voltages of anodization on tube diameter. Spectroscopy measurements pointed out the red shift in diffusion reflectance spectra after deposition of vanadium oxide. The presence of V5+ oxidation state has been detected on the surface of nanotube arrays by chemical analysis. CH3NH3PbI3 monocrystal was dry pressed on top of the nanotubes in order to make a photodiode. The current-voltage characteristics of the photodiode were recorded and it was observed that the sample with the smallest wall thickness and higher amount of vanadium has the best photocurrent response.
PB  - Belgrade : Serbian Ceramic Society
C3  - Program and the Book of Abstracts / Serbian Ceramic Society Conference - Advanced Ceramics and Application X, New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 26-27. September 2022.
T1  - Characteristic of photodiode based on vanadium oxide-TiO2 nanotubes/CH3NH3PbI3
UR  - https://hdl.handle.net/21.15107/rcub_machinery_4226
ER  - 

@conference{
author = "Vujančević, Jelena and Blagojević, Vladimir A. and Andričević, Pavao and Pavlović, Vera P. and Horvath, Endre and Forro, Laszlo and Vlahović, Branislav and Pavlović, Vladimir B. and Janaćković, Đorđe",
year = "2022",
abstract = "The aim of this study was to investigate the influence of the deposition of vanadium oxide epitaxial layer on the photoresponse of TiO2/CH3NH3PbI3 heterojunction. TiO2 nanotube array was synthesized via anodization of titanium foil at three different voltages. After annealing at 450 °C, vanadium oxide was deposited by direct deposition from vanadyl(IV) sulfate solution. Microstructure analysis has been used for the investigation of the influence of different voltages of anodization on tube diameter. Spectroscopy measurements pointed out the red shift in diffusion reflectance spectra after deposition of vanadium oxide. The presence of V5+ oxidation state has been detected on the surface of nanotube arrays by chemical analysis. CH3NH3PbI3 monocrystal was dry pressed on top of the nanotubes in order to make a photodiode. The current-voltage characteristics of the photodiode were recorded and it was observed that the sample with the smallest wall thickness and higher amount of vanadium has the best photocurrent response.",
publisher = "Belgrade : Serbian Ceramic Society",
journal = "Program and the Book of Abstracts / Serbian Ceramic Society Conference - Advanced Ceramics and Application X, New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 26-27. September 2022.",
title = "Characteristic of photodiode based on vanadium oxide-TiO2 nanotubes/CH3NH3PbI3",
url = "https://hdl.handle.net/21.15107/rcub_machinery_4226"
}

Vujančević, J., Blagojević, V. A., Andričević, P., Pavlović, V. P., Horvath, E., Forro, L., Vlahović, B., Pavlović, V. B.,& Janaćković, Đ.. (2022). Characteristic of photodiode based on vanadium oxide-TiO2 nanotubes/CH3NH3PbI3. in Program and the Book of Abstracts / Serbian Ceramic Society Conference - Advanced Ceramics and Application X, New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 26-27. September 2022.
Belgrade : Serbian Ceramic Society..
https://hdl.handle.net/21.15107/rcub_machinery_4226

Vujančević J, Blagojević VA, Andričević P, Pavlović VP, Horvath E, Forro L, Vlahović B, Pavlović VB, Janaćković Đ. Characteristic of photodiode based on vanadium oxide-TiO2 nanotubes/CH3NH3PbI3. in Program and the Book of Abstracts / Serbian Ceramic Society Conference - Advanced Ceramics and Application X, New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 26-27. September 2022.. 2022;.
https://hdl.handle.net/21.15107/rcub_machinery_4226 .

Vujančević, Jelena, Blagojević, Vladimir A., Andričević, Pavao, Pavlović, Vera P., Horvath, Endre, Forro, Laszlo, Vlahović, Branislav, Pavlović, Vladimir B., Janaćković, Đorđe, "Characteristic of photodiode based on vanadium oxide-TiO2 nanotubes/CH3NH3PbI3" in Program and the Book of Abstracts / Serbian Ceramic Society Conference - Advanced Ceramics and Application X, New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 26-27. September 2022. (2022),
https://hdl.handle.net/21.15107/rcub_machinery_4226 .

TY  - JOUR
AU  - Živojinović, Jelena
AU  - Kosanović, Darko
AU  - Blagojević, Vladimir A.
AU  - Pavlović, Vera P.
AU  - Tadić, Nenad
AU  - Vlahović, Branislav
AU  - Pavlović, Vladimir B.
PY  - 2022
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/4201
AB  - In this study, microstructure evolution and dielectric properties of SrTiO3 ceramic have been investigated, whereby mechanical activation of SrTiO3 powders was used to modify the functional properties of ceramic materials. Microstructural SEM analysis of SrTiO3 ceramics showed that the increase in mechanical activation time results in less porous samples. Raman spectroscopy indicated changes in the broadening and asymmetry of the TO2 mode with a change in the time of mechanical activation. TO2 mode showed a Fano asymmetry due to its interaction with polarization fluctuations in polar micro-regions, which are a consequence of the presence of oxygen vacancies caused by activation. The maximum value of dielectric permittivity was observed in the sample activated for 10 min. Also, the sample activated for 10 min exhibits relatively low values of loss tangent, compared to the other mechanically activated samples, providing the best overall dielectric performance compared to other samples.
PB  - ETRAN
T2  - Science of Sintering
T1  - Dielectric Properties of Mechanically Activated Strontium Titanate Ceramics
EP  - 414
IS  - 4
SP  - 401
VL  - 54
DO  - 10.2298/SOS2204401Z
ER  - 

@article{
author = "Živojinović, Jelena and Kosanović, Darko and Blagojević, Vladimir A. and Pavlović, Vera P. and Tadić, Nenad and Vlahović, Branislav and Pavlović, Vladimir B.",
year = "2022",
abstract = "In this study, microstructure evolution and dielectric properties of SrTiO3 ceramic have been investigated, whereby mechanical activation of SrTiO3 powders was used to modify the functional properties of ceramic materials. Microstructural SEM analysis of SrTiO3 ceramics showed that the increase in mechanical activation time results in less porous samples. Raman spectroscopy indicated changes in the broadening and asymmetry of the TO2 mode with a change in the time of mechanical activation. TO2 mode showed a Fano asymmetry due to its interaction with polarization fluctuations in polar micro-regions, which are a consequence of the presence of oxygen vacancies caused by activation. The maximum value of dielectric permittivity was observed in the sample activated for 10 min. Also, the sample activated for 10 min exhibits relatively low values of loss tangent, compared to the other mechanically activated samples, providing the best overall dielectric performance compared to other samples.",
publisher = "ETRAN",
journal = "Science of Sintering",
title = "Dielectric Properties of Mechanically Activated Strontium Titanate Ceramics",
pages = "414-401",
number = "4",
volume = "54",
doi = "10.2298/SOS2204401Z"
}

Živojinović, J., Kosanović, D., Blagojević, V. A., Pavlović, V. P., Tadić, N., Vlahović, B.,& Pavlović, V. B.. (2022). Dielectric Properties of Mechanically Activated Strontium Titanate Ceramics. in Science of Sintering
ETRAN., 54(4), 401-414.
https://doi.org/10.2298/SOS2204401Z

Živojinović J, Kosanović D, Blagojević VA, Pavlović VP, Tadić N, Vlahović B, Pavlović VB. Dielectric Properties of Mechanically Activated Strontium Titanate Ceramics. in Science of Sintering. 2022;54(4):401-414.
doi:10.2298/SOS2204401Z .

Živojinović, Jelena, Kosanović, Darko, Blagojević, Vladimir A., Pavlović, Vera P., Tadić, Nenad, Vlahović, Branislav, Pavlović, Vladimir B., "Dielectric Properties of Mechanically Activated Strontium Titanate Ceramics" in Science of Sintering, 54, no. 4 (2022):401-414,
https://doi.org/10.2298/SOS2204401Z . .

TY  - JOUR
AU  - Stevanović, Snežana M.
AU  - Petrović, Tanja S.
AU  - Marković, Dragan
AU  - Milovančević, Uroš
AU  - Stevanović, Simo V
AU  - Urošević, Tijana M.
AU  - Kozarski, Maja S.
PY  - 2021
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/102
AB  - The effects of different freezing methods and long-term frozen storage on quality of strawberry and raspberry were investigated, that is, the retention of initial property and free radical scavenging (AO) activity after individual quick freezing (IQF) and conventional (discontinuous) freezing. The physicochemical properties, vitamin C, and AO activity were more affected by long-term frozen storage than by freezing itself; however, their better retention was obtained after IQF. Moreover, AO activity was found to be higher in frozen samples compared to fresh fruits, but significant decrease was detected after 8 months of frozen storage. Despite the significantly higher initial content of vitamin C in strawberry, it demonstrated a lower AO activity than raspberry. Sensory attributes were significantly affected by freezing; the most considerable changes were recorded on their texture/firmness, especially after conventional (slow) freezing. Therefore, IQF can generally be suggested as a more suitable method of preserving these delicate fruits than slow freezing. Practical applications Nowadays, consumers are increasingly interested in foods that possess not only good nutritional value but also health-promoting property. Berries are known as rich sources of micronutrients and antioxidant compounds, but consumption of fresh strawberry and raspberry fruits may be limited because of seasonal and market availability; therefore, they must be preserved commonly by freezing. Frozen food industry is of crucial importance for developing countries, in which the fast freezing industry is rapidly developed. Investigation of the effect of industrial freezing and frozen storage on retention of the quality-related property and antioxidant activity is important for providing the best quality for consumers and health benefits, as well as international fruit trade. In addition, the results obtained in this study could provide best practice and guidance for the frozen fruit industry.
PB  - Wiley, Hoboken
T2  - Journal of Food Processing and Preservation
T1  - Changes of quality and free radical scavenging activity of strawberry and raspberry frozen under different conditions
DO  - 10.1111/jfpp.15981
ER  - 

@article{
author = "Stevanović, Snežana M. and Petrović, Tanja S. and Marković, Dragan and Milovančević, Uroš and Stevanović, Simo V and Urošević, Tijana M. and Kozarski, Maja S.",
year = "2021",
abstract = "The effects of different freezing methods and long-term frozen storage on quality of strawberry and raspberry were investigated, that is, the retention of initial property and free radical scavenging (AO) activity after individual quick freezing (IQF) and conventional (discontinuous) freezing. The physicochemical properties, vitamin C, and AO activity were more affected by long-term frozen storage than by freezing itself; however, their better retention was obtained after IQF. Moreover, AO activity was found to be higher in frozen samples compared to fresh fruits, but significant decrease was detected after 8 months of frozen storage. Despite the significantly higher initial content of vitamin C in strawberry, it demonstrated a lower AO activity than raspberry. Sensory attributes were significantly affected by freezing; the most considerable changes were recorded on their texture/firmness, especially after conventional (slow) freezing. Therefore, IQF can generally be suggested as a more suitable method of preserving these delicate fruits than slow freezing. Practical applications Nowadays, consumers are increasingly interested in foods that possess not only good nutritional value but also health-promoting property. Berries are known as rich sources of micronutrients and antioxidant compounds, but consumption of fresh strawberry and raspberry fruits may be limited because of seasonal and market availability; therefore, they must be preserved commonly by freezing. Frozen food industry is of crucial importance for developing countries, in which the fast freezing industry is rapidly developed. Investigation of the effect of industrial freezing and frozen storage on retention of the quality-related property and antioxidant activity is important for providing the best quality for consumers and health benefits, as well as international fruit trade. In addition, the results obtained in this study could provide best practice and guidance for the frozen fruit industry.",
publisher = "Wiley, Hoboken",
journal = "Journal of Food Processing and Preservation",
title = "Changes of quality and free radical scavenging activity of strawberry and raspberry frozen under different conditions",
doi = "10.1111/jfpp.15981"
}

Stevanović, S. M., Petrović, T. S., Marković, D., Milovančević, U., Stevanović, S. V., Urošević, T. M.,& Kozarski, M. S.. (2021). Changes of quality and free radical scavenging activity of strawberry and raspberry frozen under different conditions. in Journal of Food Processing and Preservation
Wiley, Hoboken..
https://doi.org/10.1111/jfpp.15981

Stevanović SM, Petrović TS, Marković D, Milovančević U, Stevanović SV, Urošević TM, Kozarski MS. Changes of quality and free radical scavenging activity of strawberry and raspberry frozen under different conditions. in Journal of Food Processing and Preservation. 2021;.
doi:10.1111/jfpp.15981 .

Stevanović, Snežana M., Petrović, Tanja S., Marković, Dragan, Milovančević, Uroš, Stevanović, Simo V, Urošević, Tijana M., Kozarski, Maja S., "Changes of quality and free radical scavenging activity of strawberry and raspberry frozen under different conditions" in Journal of Food Processing and Preservation (2021),
https://doi.org/10.1111/jfpp.15981 . .

TY  - CONF
AU  - Živković, Milovan
AU  - Dražić, Milan
AU  - Gligorević, Kosta
AU  - Pajić, Miloš
AU  - Bošković, Biljana
AU  - Zlatanović, Ivan
AU  - Simonović, Vojislav
PY  - 2021
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/5025
AB  - Performing works with the land where a lot of mechanical work is engaged, such as making pits for planting fruit, needs to be mechanized. This replaces human labour with a tractor machine aggregate with an increase in productivity and thus makes the process cheaper. For the proper selection of individual means of mechanization, it is important to determine the optimal 
agrotechnical parameters of their application. Proper selection and use of mechanization tools for planting have a decisive influence on the intensity and progress in cultivation technology. Defining 
energy and exploitation parameters of tractor-machine aggregates during mechanized construction of pits is the subject of this research. The pits are intended for individual planting of 
fruit seedlings as well as the installation of trellis poles. The test results of the tractor-machine aggregate show that the lowest driving force engaged for drilling was achieved in the field and 
was 6.36 kW for the excavated pit with the depth of 885 mm and with a diameter of 520 mm, the number of revolutions of the drill was 93 rpm and drilling was achieved in 27 s. The highest 
driving force for drilling was engaged in field III, which was 30.8 kW for the excavated pit 780 mm deep with a diameter of 490 mm, the number of revolutions of the drill bit was 111 rpm and 
drilling was realized in 30 s. The results obtained in these tests show that the consumption of motor power largely depends on the type of soil, the quality of previous soil preparations and the number of revolutions of the tractor PTO shaft. The time required to move the aggregate from one to the next drilling site is crucially influenced by the terrain configuration, the state of soil preparation and the skill of the tractor driver and auxiliary worker.
PB  - University of Belgrade, Faculty of Agriculture, The Institute for Agricultural Engineering
C3  - The Fifth International Symposium on Agricultural Engineering - ISAE-2021, Proceedingss
T1  - TMA exploitation indicators for mechanized drilling of pits for planting fruit
EP  - I-12
SP  - I-1
UR  - https://hdl.handle.net/21.15107/rcub_machinery_5025
ER  - 

@conference{
author = "Živković, Milovan and Dražić, Milan and Gligorević, Kosta and Pajić, Miloš and Bošković, Biljana and Zlatanović, Ivan and Simonović, Vojislav",
year = "2021",
abstract = "Performing works with the land where a lot of mechanical work is engaged, such as making pits for planting fruit, needs to be mechanized. This replaces human labour with a tractor machine aggregate with an increase in productivity and thus makes the process cheaper. For the proper selection of individual means of mechanization, it is important to determine the optimal 
agrotechnical parameters of their application. Proper selection and use of mechanization tools for planting have a decisive influence on the intensity and progress in cultivation technology. Defining 
energy and exploitation parameters of tractor-machine aggregates during mechanized construction of pits is the subject of this research. The pits are intended for individual planting of 
fruit seedlings as well as the installation of trellis poles. The test results of the tractor-machine aggregate show that the lowest driving force engaged for drilling was achieved in the field and 
was 6.36 kW for the excavated pit with the depth of 885 mm and with a diameter of 520 mm, the number of revolutions of the drill was 93 rpm and drilling was achieved in 27 s. The highest 
driving force for drilling was engaged in field III, which was 30.8 kW for the excavated pit 780 mm deep with a diameter of 490 mm, the number of revolutions of the drill bit was 111 rpm and 
drilling was realized in 30 s. The results obtained in these tests show that the consumption of motor power largely depends on the type of soil, the quality of previous soil preparations and the number of revolutions of the tractor PTO shaft. The time required to move the aggregate from one to the next drilling site is crucially influenced by the terrain configuration, the state of soil preparation and the skill of the tractor driver and auxiliary worker.",
publisher = "University of Belgrade, Faculty of Agriculture, The Institute for Agricultural Engineering",
journal = "The Fifth International Symposium on Agricultural Engineering - ISAE-2021, Proceedingss",
title = "TMA exploitation indicators for mechanized drilling of pits for planting fruit",
pages = "I-12-I-1",
url = "https://hdl.handle.net/21.15107/rcub_machinery_5025"
}

Živković, M., Dražić, M., Gligorević, K., Pajić, M., Bošković, B., Zlatanović, I.,& Simonović, V.. (2021). TMA exploitation indicators for mechanized drilling of pits for planting fruit. in The Fifth International Symposium on Agricultural Engineering - ISAE-2021, Proceedingss
University of Belgrade, Faculty of Agriculture, The Institute for Agricultural Engineering., I-1-I-12.
https://hdl.handle.net/21.15107/rcub_machinery_5025

Živković M, Dražić M, Gligorević K, Pajić M, Bošković B, Zlatanović I, Simonović V. TMA exploitation indicators for mechanized drilling of pits for planting fruit. in The Fifth International Symposium on Agricultural Engineering - ISAE-2021, Proceedingss. 2021;:I-1-I-12.
https://hdl.handle.net/21.15107/rcub_machinery_5025 .

Živković, Milovan, Dražić, Milan, Gligorević, Kosta, Pajić, Miloš, Bošković, Biljana, Zlatanović, Ivan, Simonović, Vojislav, "TMA exploitation indicators for mechanized drilling of pits for planting fruit" in The Fifth International Symposium on Agricultural Engineering - ISAE-2021, Proceedingss (2021):I-1-I-12,
https://hdl.handle.net/21.15107/rcub_machinery_5025 .

TY  - CONF
AU  - Dražić, MIlan
AU  - Gligorević, Kosta
AU  - Pajić, Miloš
AU  - Živković, Milovan
AU  - Zlatanović, Ivan
AU  - Simonović, Vojislav
AU  - Bošković, Biljana
PY  - 2021
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/5032
AB  - Hay is a bulky part of the meal that is most often used in the winter period of the 
year in all types of ruminants, while the role of hay in the meal of high-milk cows is invaluable. 
The most common way to produce hay is to dry the cut grass on the surface of the land in the field, 
using the energy of the sun. In the process of hay production, there is a reduction of nutrients in 
relation to the green mass, where the achieved yield and quality of hay largely depends on the 
technological operations that are performed during storage. In the baling process, the dried mass 
is exposed to the mechanical treatment of the working elements of the press, as a result of which 
the leaf mass decreases. Loss of leaf mass, which contains a large amount of nutrients, can greatly 
affect the achieved yield and quality of the obtained hay. One of the possibilities to reduce losses is 
the application of "DewPoint" technology, which involves the use of water vapor in the baling 
process. The steam produced by the device is injected into the mass-hay after lifting by the pickup 
device and further until the mass enters the pressing chamber. Mass treatment is achieved by 
injecting steam through a series of nozzles located inside the press. Water vapor is an extremely 
efficient medium for the controlled hydration of hay during the baling process, where 
approximately 450 l of water vapor can be produced from 1 l of water. By applying this 
technology, water consumption is 5-7 l per 1 t of hay, producing 2250-3150 l of water vapor. This 
amount of steam enables efficient treatment of individual plants (tree, leaf) in a mass of 1t to the 
desired humidity level.
PB  - University of Belgrade, Faculty of Agriculture, The Institute for Agricultural Engineering
C3  - The Fifth International Symposium on Agricultural Engineering - ISAE-2021, Proceedings
T1  - Reduction of plant weight loss in the process of hay baling using water steam
EP  - I-73
SP  - I-63
UR  - https://hdl.handle.net/21.15107/rcub_machinery_5032
ER  - 

@conference{
author = "Dražić, MIlan and Gligorević, Kosta and Pajić, Miloš and Živković, Milovan and Zlatanović, Ivan and Simonović, Vojislav and Bošković, Biljana",
year = "2021",
abstract = "Hay is a bulky part of the meal that is most often used in the winter period of the 
year in all types of ruminants, while the role of hay in the meal of high-milk cows is invaluable. 
The most common way to produce hay is to dry the cut grass on the surface of the land in the field, 
using the energy of the sun. In the process of hay production, there is a reduction of nutrients in 
relation to the green mass, where the achieved yield and quality of hay largely depends on the 
technological operations that are performed during storage. In the baling process, the dried mass 
is exposed to the mechanical treatment of the working elements of the press, as a result of which 
the leaf mass decreases. Loss of leaf mass, which contains a large amount of nutrients, can greatly 
affect the achieved yield and quality of the obtained hay. One of the possibilities to reduce losses is 
the application of "DewPoint" technology, which involves the use of water vapor in the baling 
process. The steam produced by the device is injected into the mass-hay after lifting by the pickup 
device and further until the mass enters the pressing chamber. Mass treatment is achieved by 
injecting steam through a series of nozzles located inside the press. Water vapor is an extremely 
efficient medium for the controlled hydration of hay during the baling process, where 
approximately 450 l of water vapor can be produced from 1 l of water. By applying this 
technology, water consumption is 5-7 l per 1 t of hay, producing 2250-3150 l of water vapor. This 
amount of steam enables efficient treatment of individual plants (tree, leaf) in a mass of 1t to the 
desired humidity level.",
publisher = "University of Belgrade, Faculty of Agriculture, The Institute for Agricultural Engineering",
journal = "The Fifth International Symposium on Agricultural Engineering - ISAE-2021, Proceedings",
title = "Reduction of plant weight loss in the process of hay baling using water steam",
pages = "I-73-I-63",
url = "https://hdl.handle.net/21.15107/rcub_machinery_5032"
}

Dražić, M., Gligorević, K., Pajić, M., Živković, M., Zlatanović, I., Simonović, V.,& Bošković, B.. (2021). Reduction of plant weight loss in the process of hay baling using water steam. in The Fifth International Symposium on Agricultural Engineering - ISAE-2021, Proceedings
University of Belgrade, Faculty of Agriculture, The Institute for Agricultural Engineering., I-63-I-73.
https://hdl.handle.net/21.15107/rcub_machinery_5032

Dražić M, Gligorević K, Pajić M, Živković M, Zlatanović I, Simonović V, Bošković B. Reduction of plant weight loss in the process of hay baling using water steam. in The Fifth International Symposium on Agricultural Engineering - ISAE-2021, Proceedings. 2021;:I-63-I-73.
https://hdl.handle.net/21.15107/rcub_machinery_5032 .

Dražić, MIlan, Gligorević, Kosta, Pajić, Miloš, Živković, Milovan, Zlatanović, Ivan, Simonović, Vojislav, Bošković, Biljana, "Reduction of plant weight loss in the process of hay baling using water steam" in The Fifth International Symposium on Agricultural Engineering - ISAE-2021, Proceedings (2021):I-63-I-73,
https://hdl.handle.net/21.15107/rcub_machinery_5032 .

TY  - CONF
AU  - Pajić, Miloš
AU  - Bošković, Biljana
AU  - Dražić, Milan
AU  - Gligorević, Kosta
AU  - Živković, Milovan
AU  - Simonović, Vojislav
AU  - Zlatanović, Ivan
PY  - 2021
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/5034
AB  - The application of precision agriculture in chemical plant protection enables the 
realization of high yields while preserving natural resources. The quality of chemical applications 
depends on the type of technical system that performs for this job. The task of the technical system 
is to protect the cultivated crop precisely, economically and while preserving the environment, and 
all that depends on the precission and the quality of application of the protective liquid. The use of 
UAV´s in chemical plant protection enables precise application of protective liquid, so their 
application is increasing in the protection of numerous crops. The same trend has been observed 
in field production, where the use of UAV´s is on the rise. The paper compares the exploatational 
and technological characteristics of the field sprayer (FS) and unmanned aerial vehicle (UAV) in 
the chemical protection of wheat. The amount of deposited protective liquid on plants and losses of 
deposited on the surface of the earth were monitored. Using UAV (T4: V = 3 m·s-1
, H = 1 m), the 
amount of protective liquid on the plant was determined to be 0.185 mg·l-1
compared to 0.037 mg·l 1
at FS, while the losses were 0.01 mg·l-1
at FS and 0.085 mg·l-1
at UAV. The presence of Fusarium 
(Fusarium spp.) after chemical protection was analyzed according to the compared technical 
systems and set treatments. It was recorded for 20% higher efficiency in protection against 
Fusarium (Fusarium spp.) using UAV (T5: V = 3 m·s-1
, H = 2 m) compared to FS. The values of 
wheat yield were measured according to the compared technical systems and set treatments, where 
the highest wheat yield was achieved using UAV (T5) with 10,667.7 kg·ha-1
, while using FS, 
14.84% lower yield was achieved. The application of UAV´s in the segment of chemical plant 
protection enables us to effectively protect crops, economical and optimized production, while 
preserving the environment in a way that has been completely new and unknown until now.
PB  - University of Belgrade, Faculty of Agriculture, The Institute for Agricultural Engineering
C3  - The Fifth International Symposium on Agricultural Engineering - ISAE-2021, Proceedings
T1  - Application of contemporary technical systems in chemical protection of field crops: case study of wheat production in Serbia
EP  - II-29
SP  - II-22
UR  - https://hdl.handle.net/21.15107/rcub_machinery_5034
ER  - 

@conference{
author = "Pajić, Miloš and Bošković, Biljana and Dražić, Milan and Gligorević, Kosta and Živković, Milovan and Simonović, Vojislav and Zlatanović, Ivan",
year = "2021",
abstract = "The application of precision agriculture in chemical plant protection enables the 
realization of high yields while preserving natural resources. The quality of chemical applications 
depends on the type of technical system that performs for this job. The task of the technical system 
is to protect the cultivated crop precisely, economically and while preserving the environment, and 
all that depends on the precission and the quality of application of the protective liquid. The use of 
UAV´s in chemical plant protection enables precise application of protective liquid, so their 
application is increasing in the protection of numerous crops. The same trend has been observed 
in field production, where the use of UAV´s is on the rise. The paper compares the exploatational 
and technological characteristics of the field sprayer (FS) and unmanned aerial vehicle (UAV) in 
the chemical protection of wheat. The amount of deposited protective liquid on plants and losses of 
deposited on the surface of the earth were monitored. Using UAV (T4: V = 3 m·s-1
, H = 1 m), the 
amount of protective liquid on the plant was determined to be 0.185 mg·l-1
compared to 0.037 mg·l 1
at FS, while the losses were 0.01 mg·l-1
at FS and 0.085 mg·l-1
at UAV. The presence of Fusarium 
(Fusarium spp.) after chemical protection was analyzed according to the compared technical 
systems and set treatments. It was recorded for 20% higher efficiency in protection against 
Fusarium (Fusarium spp.) using UAV (T5: V = 3 m·s-1
, H = 2 m) compared to FS. The values of 
wheat yield were measured according to the compared technical systems and set treatments, where 
the highest wheat yield was achieved using UAV (T5) with 10,667.7 kg·ha-1
, while using FS, 
14.84% lower yield was achieved. The application of UAV´s in the segment of chemical plant 
protection enables us to effectively protect crops, economical and optimized production, while 
preserving the environment in a way that has been completely new and unknown until now.",
publisher = "University of Belgrade, Faculty of Agriculture, The Institute for Agricultural Engineering",
journal = "The Fifth International Symposium on Agricultural Engineering - ISAE-2021, Proceedings",
title = "Application of contemporary technical systems in chemical protection of field crops: case study of wheat production in Serbia",
pages = "II-29-II-22",
url = "https://hdl.handle.net/21.15107/rcub_machinery_5034"
}

Pajić, M., Bošković, B., Dražić, M., Gligorević, K., Živković, M., Simonović, V.,& Zlatanović, I.. (2021). Application of contemporary technical systems in chemical protection of field crops: case study of wheat production in Serbia. in The Fifth International Symposium on Agricultural Engineering - ISAE-2021, Proceedings
University of Belgrade, Faculty of Agriculture, The Institute for Agricultural Engineering., II-22-II-29.
https://hdl.handle.net/21.15107/rcub_machinery_5034

Pajić M, Bošković B, Dražić M, Gligorević K, Živković M, Simonović V, Zlatanović I. Application of contemporary technical systems in chemical protection of field crops: case study of wheat production in Serbia. in The Fifth International Symposium on Agricultural Engineering - ISAE-2021, Proceedings. 2021;:II-22-II-29.
https://hdl.handle.net/21.15107/rcub_machinery_5034 .

Pajić, Miloš, Bošković, Biljana, Dražić, Milan, Gligorević, Kosta, Živković, Milovan, Simonović, Vojislav, Zlatanović, Ivan, "Application of contemporary technical systems in chemical protection of field crops: case study of wheat production in Serbia" in The Fifth International Symposium on Agricultural Engineering - ISAE-2021, Proceedings (2021):II-22-II-29,
https://hdl.handle.net/21.15107/rcub_machinery_5034 .

TY  - CONF
AU  - Vujančević, Jelena
AU  - Blagojević, Vladimir A.
AU  - Andričević, Pavao
AU  - Pavlović, Vera P.
AU  - Horvath, Endre
AU  - Forro, Laszlo
AU  - Vlahović, Branislav
AU  - Pavlović, Vladimir B.
AU  - Janaćković, Đorđe
PY  - 2021
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/4223
AB  - The aim of this study was to investigate the influence of vanadium oxide photosensitive surface layer on the photoactivity of TiO2 nanotubes. Nanotube arrays were synthesized by anodization of titanium foil at different voltages, and vanadium-oxide was deposited by wet chemical deposition. Deposition of the vanadium-oxide layer was confirmed by XPS analysis, which provided the chemical composition of the sample surface. Photovoltaic characteristics and photocatalytic performance for photodegradation of methyl orange dye of modified TiO2 nanotubes were correlated with the nanotube morphology (and anodization voltage). Optimal anodization voltage was determined, in conjunction with the deposition of the surface vanadium oxide layer, in order to achieve maximum performance of the modified TiO2 electrodes. This has been correlated with changes in the optical properties of the TiO2 electrodes, the nanotube length and diameter, as they occur with the change in the anodization voltage, as well as the changes in the vanadium-oxide content in the samples, where the vanadium-oxide content was found to be determined by the nanotube morphology. The photovoltaic performance of the optimized modified TiO2 electrode with the surface vanadium-oxide layer was found to be significantly better than both the performance of the corresponding TiO2 electrode, and the performance of all the other TiO2 electrodes included in the study.
PB  - Faculty of Technology, University of Novi Sad
C3  - Programme and Book of Abstracts of the ECerS 14th Conference for Young Scientists in Ceramics (CYSC-2021), October 20-23, 2021, Novi Sad, Serbia
T1  - Photoactivity of vanadium oxide TiO2 nanotubes
UR  - https://hdl.handle.net/21.15107/rcub_machinery_4223
ER  - 

@conference{
author = "Vujančević, Jelena and Blagojević, Vladimir A. and Andričević, Pavao and Pavlović, Vera P. and Horvath, Endre and Forro, Laszlo and Vlahović, Branislav and Pavlović, Vladimir B. and Janaćković, Đorđe",
year = "2021",
abstract = "The aim of this study was to investigate the influence of vanadium oxide photosensitive surface layer on the photoactivity of TiO2 nanotubes. Nanotube arrays were synthesized by anodization of titanium foil at different voltages, and vanadium-oxide was deposited by wet chemical deposition. Deposition of the vanadium-oxide layer was confirmed by XPS analysis, which provided the chemical composition of the sample surface. Photovoltaic characteristics and photocatalytic performance for photodegradation of methyl orange dye of modified TiO2 nanotubes were correlated with the nanotube morphology (and anodization voltage). Optimal anodization voltage was determined, in conjunction with the deposition of the surface vanadium oxide layer, in order to achieve maximum performance of the modified TiO2 electrodes. This has been correlated with changes in the optical properties of the TiO2 electrodes, the nanotube length and diameter, as they occur with the change in the anodization voltage, as well as the changes in the vanadium-oxide content in the samples, where the vanadium-oxide content was found to be determined by the nanotube morphology. The photovoltaic performance of the optimized modified TiO2 electrode with the surface vanadium-oxide layer was found to be significantly better than both the performance of the corresponding TiO2 electrode, and the performance of all the other TiO2 electrodes included in the study.",
publisher = "Faculty of Technology, University of Novi Sad",
journal = "Programme and Book of Abstracts of the ECerS 14th Conference for Young Scientists in Ceramics (CYSC-2021), October 20-23, 2021, Novi Sad, Serbia",
title = "Photoactivity of vanadium oxide TiO2 nanotubes",
url = "https://hdl.handle.net/21.15107/rcub_machinery_4223"
}

Vujančević, J., Blagojević, V. A., Andričević, P., Pavlović, V. P., Horvath, E., Forro, L., Vlahović, B., Pavlović, V. B.,& Janaćković, Đ.. (2021). Photoactivity of vanadium oxide TiO2 nanotubes. in Programme and Book of Abstracts of the ECerS 14th Conference for Young Scientists in Ceramics (CYSC-2021), October 20-23, 2021, Novi Sad, Serbia
Faculty of Technology, University of Novi Sad..
https://hdl.handle.net/21.15107/rcub_machinery_4223

Vujančević J, Blagojević VA, Andričević P, Pavlović VP, Horvath E, Forro L, Vlahović B, Pavlović VB, Janaćković Đ. Photoactivity of vanadium oxide TiO2 nanotubes. in Programme and Book of Abstracts of the ECerS 14th Conference for Young Scientists in Ceramics (CYSC-2021), October 20-23, 2021, Novi Sad, Serbia. 2021;.
https://hdl.handle.net/21.15107/rcub_machinery_4223 .

Vujančević, Jelena, Blagojević, Vladimir A., Andričević, Pavao, Pavlović, Vera P., Horvath, Endre, Forro, Laszlo, Vlahović, Branislav, Pavlović, Vladimir B., Janaćković, Đorđe, "Photoactivity of vanadium oxide TiO2 nanotubes" in Programme and Book of Abstracts of the ECerS 14th Conference for Young Scientists in Ceramics (CYSC-2021), October 20-23, 2021, Novi Sad, Serbia (2021),
https://hdl.handle.net/21.15107/rcub_machinery_4223 .

TY  - CONF
AU  - Živojinović, Jelena
AU  - Blagojević, Vladimir A.
AU  - Pavlović, Vera P.
AU  - Kosanović, Darko
AU  - Tadić, Nenad
AU  - Pavlović, Vladimir B.
PY  - 2021
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/4224
AB  - In recent years, a lot of interest has been shown in obtaining materials with predetermined properties. The aim is to establish a functional dependence between the synthesis parameters, structural characteristics, and properties of the material. Ceramic materials based on strontium titanate (SrTiO3) are of special interest due to their unique physical-chemical properties. Having in mind the importance of examining the influence of synthesis parameters on the process of obtaining and properties of functional electroceramic materials, and the importance of SrTiO3 as a perovskite material, the motive was to analyze and consider the influence of mechanical activation. It has been established that the time of mechanical activation (0, 10, 30, 60, 90, and 120 minutes) of SrTiO3 powders indirectly affects on electrical properties of SrTiO3 ceramics. It was noticed that in SrTiO3 ceramics the values of relative dielectric permittivity in the radio frequency range (0,3 MHz - 3 GHz) are stable, which is important for the fabrication of electronic components. Microstructural SEM analysis showed that the increase in mechanical activation time results in less porous samples. It was found that the value of the relative dielectric permittivity of ceramic samples at room temperature changes following the combined effect of changes in sample density, grain size, as well as changes in the grain boundary region. The maximum value of dielectric permittivity was observed in the sample activated for 10 minutes. Also, the sample activated for 10 min exhibits relatively low values of loss tangent, compared to the other mechanically activated samples, providing the best overall dielectric performance compared to other samples.
PB  - Innovation Center of Faculty of Mechanical Engineering, Belgrade
C3  - Programme and The Book of Abstracts - International Conference of Experimental and Numerical Investigations and New Technologies - CNN TECH 2021, 29 June - 02 July 2021, Zlatibor, Serbia
T1  - The influence of mechanical activation on microstructure and dielectric properties of SrTiO3 ceramics
UR  - https://hdl.handle.net/21.15107/rcub_machinery_4224
ER  - 

@conference{
author = "Živojinović, Jelena and Blagojević, Vladimir A. and Pavlović, Vera P. and Kosanović, Darko and Tadić, Nenad and Pavlović, Vladimir B.",
year = "2021",
abstract = "In recent years, a lot of interest has been shown in obtaining materials with predetermined properties. The aim is to establish a functional dependence between the synthesis parameters, structural characteristics, and properties of the material. Ceramic materials based on strontium titanate (SrTiO3) are of special interest due to their unique physical-chemical properties. Having in mind the importance of examining the influence of synthesis parameters on the process of obtaining and properties of functional electroceramic materials, and the importance of SrTiO3 as a perovskite material, the motive was to analyze and consider the influence of mechanical activation. It has been established that the time of mechanical activation (0, 10, 30, 60, 90, and 120 minutes) of SrTiO3 powders indirectly affects on electrical properties of SrTiO3 ceramics. It was noticed that in SrTiO3 ceramics the values of relative dielectric permittivity in the radio frequency range (0,3 MHz - 3 GHz) are stable, which is important for the fabrication of electronic components. Microstructural SEM analysis showed that the increase in mechanical activation time results in less porous samples. It was found that the value of the relative dielectric permittivity of ceramic samples at room temperature changes following the combined effect of changes in sample density, grain size, as well as changes in the grain boundary region. The maximum value of dielectric permittivity was observed in the sample activated for 10 minutes. Also, the sample activated for 10 min exhibits relatively low values of loss tangent, compared to the other mechanically activated samples, providing the best overall dielectric performance compared to other samples.",
publisher = "Innovation Center of Faculty of Mechanical Engineering, Belgrade",
journal = "Programme and The Book of Abstracts - International Conference of Experimental and Numerical Investigations and New Technologies - CNN TECH 2021, 29 June - 02 July 2021, Zlatibor, Serbia",
title = "The influence of mechanical activation on microstructure and dielectric properties of SrTiO3 ceramics",
url = "https://hdl.handle.net/21.15107/rcub_machinery_4224"
}

Živojinović, J., Blagojević, V. A., Pavlović, V. P., Kosanović, D., Tadić, N.,& Pavlović, V. B.. (2021). The influence of mechanical activation on microstructure and dielectric properties of SrTiO3 ceramics. in Programme and The Book of Abstracts - International Conference of Experimental and Numerical Investigations and New Technologies - CNN TECH 2021, 29 June - 02 July 2021, Zlatibor, Serbia
Innovation Center of Faculty of Mechanical Engineering, Belgrade..
https://hdl.handle.net/21.15107/rcub_machinery_4224

Živojinović J, Blagojević VA, Pavlović VP, Kosanović D, Tadić N, Pavlović VB. The influence of mechanical activation on microstructure and dielectric properties of SrTiO3 ceramics. in Programme and The Book of Abstracts - International Conference of Experimental and Numerical Investigations and New Technologies - CNN TECH 2021, 29 June - 02 July 2021, Zlatibor, Serbia. 2021;.
https://hdl.handle.net/21.15107/rcub_machinery_4224 .

Živojinović, Jelena, Blagojević, Vladimir A., Pavlović, Vera P., Kosanović, Darko, Tadić, Nenad, Pavlović, Vladimir B., "The influence of mechanical activation on microstructure and dielectric properties of SrTiO3 ceramics" in Programme and The Book of Abstracts - International Conference of Experimental and Numerical Investigations and New Technologies - CNN TECH 2021, 29 June - 02 July 2021, Zlatibor, Serbia (2021),
https://hdl.handle.net/21.15107/rcub_machinery_4224 .

TY  - CONF
AU  - Lučić, Milica
AU  - Sredović Ignjatović, Ivana
AU  - Lević, Steva
AU  - Zlatanović, Ivan
AU  - Onjia, Antonije
PY  - 2021
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/5104
AB  - Red pepper (Capsicum annum) fruits contain high amount of ascorbic acid (vitamin C), which is of 
great importance for human health. The aim of this study was to found how various pretreatments 
and drying methods influence on retention of ascorbic acid in dried pepper. The cultivar “Horgoška 
sweet 6”, often used for the production of paprika, was selected for analysis. Five sets of 
experiments were performed to investigate the effect of the following parameters: pretreatment 
temperature (20 oC, 50 oC, 80 oC), pH value (3, 6.5, 10), additive (0.25% citric acid, 0.25 % 
potassium metabisulfite and 0.25 % citric acid + 0.25 % potassium metabisulfite), ultrasound (off 
and on) and drying method (hot air drying and freeze drying). The initial content of ascorbic acid in 
fresh pepper was 292 mg/100 g dry basis (d.b.) and it was reduced after all pretreatment and after 
drying of pretreated samples. Most of examined pre-drying treatments improve retention of ascorbic 
acid in final dried peppers, except treatments at 80 oC. Our results indicate that temperature and 
drying method were parameters that significantly influenced ascorbic acid content in dried peppers. 
Other parameters were not significant, but had a certain effect on retention of ascorbic acid. The 
best parameters were temperature 20 oC, pH 6.5, citric acid/potassium metabisulfite, without 
applying ultrasound including freeze drying method.
PB  - University of Belgrade
C3  - Unifood conference, University of Belgrade, Book of Abstracts
T1  - HPLC analysis of ascorbic acid in pretreated and dried red pepper (Capsicum annum)
SP  - 179
UR  - https://hdl.handle.net/21.15107/rcub_machinery_5104
ER  - 

@conference{
author = "Lučić, Milica and Sredović Ignjatović, Ivana and Lević, Steva and Zlatanović, Ivan and Onjia, Antonije",
year = "2021",
abstract = "Red pepper (Capsicum annum) fruits contain high amount of ascorbic acid (vitamin C), which is of 
great importance for human health. The aim of this study was to found how various pretreatments 
and drying methods influence on retention of ascorbic acid in dried pepper. The cultivar “Horgoška 
sweet 6”, often used for the production of paprika, was selected for analysis. Five sets of 
experiments were performed to investigate the effect of the following parameters: pretreatment 
temperature (20 oC, 50 oC, 80 oC), pH value (3, 6.5, 10), additive (0.25% citric acid, 0.25 % 
potassium metabisulfite and 0.25 % citric acid + 0.25 % potassium metabisulfite), ultrasound (off 
and on) and drying method (hot air drying and freeze drying). The initial content of ascorbic acid in 
fresh pepper was 292 mg/100 g dry basis (d.b.) and it was reduced after all pretreatment and after 
drying of pretreated samples. Most of examined pre-drying treatments improve retention of ascorbic 
acid in final dried peppers, except treatments at 80 oC. Our results indicate that temperature and 
drying method were parameters that significantly influenced ascorbic acid content in dried peppers. 
Other parameters were not significant, but had a certain effect on retention of ascorbic acid. The 
best parameters were temperature 20 oC, pH 6.5, citric acid/potassium metabisulfite, without 
applying ultrasound including freeze drying method.",
publisher = "University of Belgrade",
journal = "Unifood conference, University of Belgrade, Book of Abstracts",
title = "HPLC analysis of ascorbic acid in pretreated and dried red pepper (Capsicum annum)",
pages = "179",
url = "https://hdl.handle.net/21.15107/rcub_machinery_5104"
}

Lučić, M., Sredović Ignjatović, I., Lević, S., Zlatanović, I.,& Onjia, A.. (2021). HPLC analysis of ascorbic acid in pretreated and dried red pepper (Capsicum annum). in Unifood conference, University of Belgrade, Book of Abstracts
University of Belgrade., 179.
https://hdl.handle.net/21.15107/rcub_machinery_5104

Lučić M, Sredović Ignjatović I, Lević S, Zlatanović I, Onjia A. HPLC analysis of ascorbic acid in pretreated and dried red pepper (Capsicum annum). in Unifood conference, University of Belgrade, Book of Abstracts. 2021;:179.
https://hdl.handle.net/21.15107/rcub_machinery_5104 .

Lučić, Milica, Sredović Ignjatović, Ivana, Lević, Steva, Zlatanović, Ivan, Onjia, Antonije, "HPLC analysis of ascorbic acid in pretreated and dried red pepper (Capsicum annum)" in Unifood conference, University of Belgrade, Book of Abstracts (2021):179,
https://hdl.handle.net/21.15107/rcub_machinery_5104 .

TY  - JOUR
AU  - Petrović, Dragan V.
AU  - Cerović, Vera
AU  - Radojević, Rade L.
AU  - Mileusnić, Zoran I.
PY  - 2021
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/3619
AB  - This paper presents an analytical algorithm with appropriate software specified for the approximation of the allowed critical slope of the solid flat terrain that guarantees static and/or dynamic stability of the specified self-propelled agricultural machines and their aggregates. This algorithm assumes machine as a rigid body, having 3 or 4 contact points (defined by wheels or crawlers), under uniform motion at different constant velocities and radii of curvature trajectories. Using this algorithm, based on the principles of theoretical mechanics combined with 3D analytical geometry, the computer program SSPM (stability of the self-propelled agricultural machines) has been coded. This software is intended to facilitate the analysis, comparison and optimization of different configurations of self-propelled agricultural machines in operation on horizontal and sloped flat terrains at constant velocities and radii of trajectory with respect to their static and dynamic stability. It calculates critical pitch and roll angles of the selfpropelled machine and the maximum allowed slope of the flat terrain under the given conditions. The algorithm and the appropriate SSPM software were experimentally verified using the platform and low-scale tractor model. Average difference between calculated and experimental critical values of roll and pitch angles were about 4 degrees
PB  - Pergamon-Elsevier Science Ltd, Oxford
T2  - Journal of Terramechanics
T1  - An approach to characterization of the agricultural self-propelled machines stability
EP  - 63
SP  - 51
VL  - 93
DO  - 10.1016/j.jterra.2020.11.001
ER  - 

@article{
author = "Petrović, Dragan V. and Cerović, Vera and Radojević, Rade L. and Mileusnić, Zoran I.",
year = "2021",
abstract = "This paper presents an analytical algorithm with appropriate software specified for the approximation of the allowed critical slope of the solid flat terrain that guarantees static and/or dynamic stability of the specified self-propelled agricultural machines and their aggregates. This algorithm assumes machine as a rigid body, having 3 or 4 contact points (defined by wheels or crawlers), under uniform motion at different constant velocities and radii of curvature trajectories. Using this algorithm, based on the principles of theoretical mechanics combined with 3D analytical geometry, the computer program SSPM (stability of the self-propelled agricultural machines) has been coded. This software is intended to facilitate the analysis, comparison and optimization of different configurations of self-propelled agricultural machines in operation on horizontal and sloped flat terrains at constant velocities and radii of trajectory with respect to their static and dynamic stability. It calculates critical pitch and roll angles of the selfpropelled machine and the maximum allowed slope of the flat terrain under the given conditions. The algorithm and the appropriate SSPM software were experimentally verified using the platform and low-scale tractor model. Average difference between calculated and experimental critical values of roll and pitch angles were about 4 degrees",
publisher = "Pergamon-Elsevier Science Ltd, Oxford",
journal = "Journal of Terramechanics",
title = "An approach to characterization of the agricultural self-propelled machines stability",
pages = "63-51",
volume = "93",
doi = "10.1016/j.jterra.2020.11.001"
}

Petrović, D. V., Cerović, V., Radojević, R. L.,& Mileusnić, Z. I.. (2021). An approach to characterization of the agricultural self-propelled machines stability. in Journal of Terramechanics
Pergamon-Elsevier Science Ltd, Oxford., 93, 51-63.
https://doi.org/10.1016/j.jterra.2020.11.001

Petrović DV, Cerović V, Radojević RL, Mileusnić ZI. An approach to characterization of the agricultural self-propelled machines stability. in Journal of Terramechanics. 2021;93:51-63.
doi:10.1016/j.jterra.2020.11.001 .

Petrović, Dragan V., Cerović, Vera, Radojević, Rade L., Mileusnić, Zoran I., "An approach to characterization of the agricultural self-propelled machines stability" in Journal of Terramechanics, 93 (2021):51-63,
https://doi.org/10.1016/j.jterra.2020.11.001 . .

TY  - CONF
AU  - Pavlović, Vera P.
AU  - Tshantshapanyan, Ani
AU  - Vlahović, Branislav
AU  - Živojinović, Jelena
AU  - Kosanović, Darko
AU  - Pavlović, Vladimir B.
PY  - 2020
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/7819
AB  - The changes in the Raman spectra of electronic materials obtained from mechanically activated BaTiO3 and SrTiO3 powders, with or without additives, are presented in this paper. Mechanical activation, performed in a high-energy planetary ball mill, was chosen as the method for the production of fine-grained nanocrystalline powders with an increased surface activity and an altered micro and/or crystal structure. Having in mind the growing relevance of the development of multiferroic materials, the analysis of Raman spectra was used not only for the structural investigations of the mechanically activated undoped titanate powder, but also for the examination of the mechanically activated Fe/BaTiO3 system and the subsequent hexaferrite formation during the sintering process. Additionally, Raman spectroscopy was applied in the study of the emergence of electroactive crystalline phases in nanocomposites based on semi-crystalline fluoropolymers, such as PVDF (polyvinylidene fluoride), in the case when mechanically activated BaTiO3 powder was used as a filler in the polymer matrix. Furthermore, the effects of the mechanical activation of SrTiO3 powder on the occurrence of polar nano and micro-regions at room temperature, as well as the simultaneous influence of activation and MnO2 addition on structural changes in ceramic SrTiO3 samples, have also been analysed using Raman spectroscopy.
PB  - Belgrade: ETRAN Society
PB  - Belgrade: Academic Mind
C3  - Зборник радова [Електронски извор] / 64. годишњa конференција за електронику, телекомуникације, рачунарство, аутоматику и нуклеарну технику EТРАН 2020 и 7. интернационалнa конференцијa за електротехнику, електронику и рачунарство ИцЕТРАН 2020 = 7th International Conference on Electrical, Electronic and Computing Engineering IcETRAN 2020 and 64th National Conference on Electrоnics, Telecommunication, Computing, Automatic Control and Nuclear Engineering ETRAN 2020
T1  - Raman spectra of the materials based on mechanically activated alkaline earth metal titanates
EP  - NMI 1.1.8
SP  - NMI 1.1.1
UR  - https://hdl.handle.net/21.15107/rcub_machinery_7819
ER  - 

@conference{
author = "Pavlović, Vera P. and Tshantshapanyan, Ani and Vlahović, Branislav and Živojinović, Jelena and Kosanović, Darko and Pavlović, Vladimir B.",
year = "2020",
abstract = "The changes in the Raman spectra of electronic materials obtained from mechanically activated BaTiO3 and SrTiO3 powders, with or without additives, are presented in this paper. Mechanical activation, performed in a high-energy planetary ball mill, was chosen as the method for the production of fine-grained nanocrystalline powders with an increased surface activity and an altered micro and/or crystal structure. Having in mind the growing relevance of the development of multiferroic materials, the analysis of Raman spectra was used not only for the structural investigations of the mechanically activated undoped titanate powder, but also for the examination of the mechanically activated Fe/BaTiO3 system and the subsequent hexaferrite formation during the sintering process. Additionally, Raman spectroscopy was applied in the study of the emergence of electroactive crystalline phases in nanocomposites based on semi-crystalline fluoropolymers, such as PVDF (polyvinylidene fluoride), in the case when mechanically activated BaTiO3 powder was used as a filler in the polymer matrix. Furthermore, the effects of the mechanical activation of SrTiO3 powder on the occurrence of polar nano and micro-regions at room temperature, as well as the simultaneous influence of activation and MnO2 addition on structural changes in ceramic SrTiO3 samples, have also been analysed using Raman spectroscopy.",
publisher = "Belgrade: ETRAN Society, Belgrade: Academic Mind",
journal = "Зборник радова [Електронски извор] / 64. годишњa конференција за електронику, телекомуникације, рачунарство, аутоматику и нуклеарну технику EТРАН 2020 и 7. интернационалнa конференцијa за електротехнику, електронику и рачунарство ИцЕТРАН 2020 = 7th International Conference on Electrical, Electronic and Computing Engineering IcETRAN 2020 and 64th National Conference on Electrоnics, Telecommunication, Computing, Automatic Control and Nuclear Engineering ETRAN 2020",
title = "Raman spectra of the materials based on mechanically activated alkaline earth metal titanates",
pages = "NMI 1.1.8-NMI 1.1.1",
url = "https://hdl.handle.net/21.15107/rcub_machinery_7819"
}

Pavlović, V. P., Tshantshapanyan, A., Vlahović, B., Živojinović, J., Kosanović, D.,& Pavlović, V. B.. (2020). Raman spectra of the materials based on mechanically activated alkaline earth metal titanates. in Зборник радова [Електронски извор] / 64. годишњa конференција за електронику, телекомуникације, рачунарство, аутоматику и нуклеарну технику EТРАН 2020 и 7. интернационалнa конференцијa за електротехнику, електронику и рачунарство ИцЕТРАН 2020 = 7th International Conference on Electrical, Electronic and Computing Engineering IcETRAN 2020 and 64th National Conference on Electrоnics, Telecommunication, Computing, Automatic Control and Nuclear Engineering ETRAN 2020
Belgrade: ETRAN Society., NMI 1.1.1-NMI 1.1.8.
https://hdl.handle.net/21.15107/rcub_machinery_7819

Pavlović VP, Tshantshapanyan A, Vlahović B, Živojinović J, Kosanović D, Pavlović VB. Raman spectra of the materials based on mechanically activated alkaline earth metal titanates. in Зборник радова [Електронски извор] / 64. годишњa конференција за електронику, телекомуникације, рачунарство, аутоматику и нуклеарну технику EТРАН 2020 и 7. интернационалнa конференцијa за електротехнику, електронику и рачунарство ИцЕТРАН 2020 = 7th International Conference on Electrical, Electronic and Computing Engineering IcETRAN 2020 and 64th National Conference on Electrоnics, Telecommunication, Computing, Automatic Control and Nuclear Engineering ETRAN 2020. 2020;:NMI 1.1.1-NMI 1.1.8.
https://hdl.handle.net/21.15107/rcub_machinery_7819 .

Pavlović, Vera P., Tshantshapanyan, Ani, Vlahović, Branislav, Živojinović, Jelena, Kosanović, Darko, Pavlović, Vladimir B., "Raman spectra of the materials based on mechanically activated alkaline earth metal titanates" in Зборник радова [Електронски извор] / 64. годишњa конференција за електронику, телекомуникације, рачунарство, аутоматику и нуклеарну технику EТРАН 2020 и 7. интернационалнa конференцијa за електротехнику, електронику и рачунарство ИцЕТРАН 2020 = 7th International Conference on Electrical, Electronic and Computing Engineering IcETRAN 2020 and 64th National Conference on Electrоnics, Telecommunication, Computing, Automatic Control and Nuclear Engineering ETRAN 2020 (2020):NMI 1.1.1-NMI 1.1.8,
https://hdl.handle.net/21.15107/rcub_machinery_7819 .

TY  - JOUR
AU  - Nedić, Nebojša M.
AU  - Gojak, Milan
AU  - Zlatanović, Ivan
AU  - Rudonja, Nedžad
AU  - Lazarević, Kristina B.
AU  - Drazić, Milan S.
AU  - Gligorević, Kosta
AU  - Pajić, Miloš B.
PY  - 2020
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/3276
AB  - The aim of this research is to study the drying kinetics of vacuum-dried and freeze-dried bee honey produced from two different varieties: Sunflower honey (Helianthus Annuus L.) and Acacia honey (Robinia pseudo acacia L.). Vacuum drying treatments were carried out with the honey samples' initial temperatures of +25 degrees C, -20 degrees C, and -40 degrees C. Water content, total soluble solids, as well as the water activity of fresh and dried honey samples were determined. Freeze-drying of bee honey with initial sample temperature of -40 degrees C has resulted in shorter drying time (7-9 hours), moisture content (10%-12%), water activity (0.405-0.427 aW) and effective moisture diffusivity coefficient (8.26.10-7-9.51.0-7 m(2)/s). The high-performance liquid chromatography method was used when analyzing the impact that drying pre-treatments had on honey quality. The application of pre-treatments has led to an increase in hydroxy-methyl-furfural by 39-71%, and a decrease in diastase activity by 17-36%, all compared to fresh honey samples. The solutions of Verma model proved to be the best fit with the experimental results.
PB  - Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd
T2  - Thermal Science
T1  - Study of vacuum and freeze drying of bee honey
EP  - 4251
IS  - 6
SP  - 4241
VL  - 24
DO  - 10.2298/TSCI200317194N
ER  - 

@article{
author = "Nedić, Nebojša M. and Gojak, Milan and Zlatanović, Ivan and Rudonja, Nedžad and Lazarević, Kristina B. and Drazić, Milan S. and Gligorević, Kosta and Pajić, Miloš B.",
year = "2020",
abstract = "The aim of this research is to study the drying kinetics of vacuum-dried and freeze-dried bee honey produced from two different varieties: Sunflower honey (Helianthus Annuus L.) and Acacia honey (Robinia pseudo acacia L.). Vacuum drying treatments were carried out with the honey samples' initial temperatures of +25 degrees C, -20 degrees C, and -40 degrees C. Water content, total soluble solids, as well as the water activity of fresh and dried honey samples were determined. Freeze-drying of bee honey with initial sample temperature of -40 degrees C has resulted in shorter drying time (7-9 hours), moisture content (10%-12%), water activity (0.405-0.427 aW) and effective moisture diffusivity coefficient (8.26.10-7-9.51.0-7 m(2)/s). The high-performance liquid chromatography method was used when analyzing the impact that drying pre-treatments had on honey quality. The application of pre-treatments has led to an increase in hydroxy-methyl-furfural by 39-71%, and a decrease in diastase activity by 17-36%, all compared to fresh honey samples. The solutions of Verma model proved to be the best fit with the experimental results.",
publisher = "Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd",
journal = "Thermal Science",
title = "Study of vacuum and freeze drying of bee honey",
pages = "4251-4241",
number = "6",
volume = "24",
doi = "10.2298/TSCI200317194N"
}

Nedić, N. M., Gojak, M., Zlatanović, I., Rudonja, N., Lazarević, K. B., Drazić, M. S., Gligorević, K.,& Pajić, M. B.. (2020). Study of vacuum and freeze drying of bee honey. in Thermal Science
Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd., 24(6), 4241-4251.
https://doi.org/10.2298/TSCI200317194N

Nedić NM, Gojak M, Zlatanović I, Rudonja N, Lazarević KB, Drazić MS, Gligorević K, Pajić MB. Study of vacuum and freeze drying of bee honey. in Thermal Science. 2020;24(6):4241-4251.
doi:10.2298/TSCI200317194N .

Nedić, Nebojša M., Gojak, Milan, Zlatanović, Ivan, Rudonja, Nedžad, Lazarević, Kristina B., Drazić, Milan S., Gligorević, Kosta, Pajić, Miloš B., "Study of vacuum and freeze drying of bee honey" in Thermal Science, 24, no. 6 (2020):4241-4251,
https://doi.org/10.2298/TSCI200317194N . .

TY  - JOUR
AU  - Pavlović, Vladimir B.
AU  - Vujančević, Jelena
AU  - Vlahović, Branislav
AU  - Pavlović, Vera P.
PY  - 2020
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/3369
AB  - Taking into account the importance of development of the advanced nanomaterials for the environmental protection, in this article the application of TiO2 based nanomaterials and nanostructures in the fields of renewable energy, chemical and bio decontamination has been presented. The role of TiO2 in formation of composite hybrid structures for solar energy harvesting has been explained, as well as the use photocatalytic degradation of pollutants. properties of TiO2 nanotubes obtained by decontamination.
AB  - Imajući u vidu značaj razvoja naprednih nanomaterijala za zaštitu prirodne okoline, u ovome radu su prezentovane primene nanomaterijala i nanostruktura na bazi TiO2 u oblastima obnovljivih izvora energije, hemijske i bio dekontaminacije. Objašnjena je uloga TiO2 u formiranju kompozitnih hibridnih struktura za prikupljanje solarne energije, kao i primena različitih antimikrobnih materijala na bazi TiO2 koji se koriste za fotokatalitičko uklanjanje polutanata. Naročita pažnja je posvećena strukturi i svojstvima titan dioksidnih nanotuba dobijenih primenom metode elektrohemijske anodizacije i njihova primena u bio dekontaminaciji.
PB  - Inženjersko društvo za koroziju, Beograd
T2  - Zaštita materijala
T1  - TiO2 based nanomaterials and nanostructures for green convergent technologies and environmental protection
T1  - Nanomaterijali i nanostrukture na bazi TiO2 za zelene konvergentne tehnologije i zaštitu prirodne okoline
EP  - 355
IS  - 4
SP  - 346
VL  - 61
DO  - 10.5937/zasmat2004346P
ER  - 

@article{
author = "Pavlović, Vladimir B. and Vujančević, Jelena and Vlahović, Branislav and Pavlović, Vera P.",
year = "2020",
abstract = "Taking into account the importance of development of the advanced nanomaterials for the environmental protection, in this article the application of TiO2 based nanomaterials and nanostructures in the fields of renewable energy, chemical and bio decontamination has been presented. The role of TiO2 in formation of composite hybrid structures for solar energy harvesting has been explained, as well as the use photocatalytic degradation of pollutants. properties of TiO2 nanotubes obtained by decontamination., Imajući u vidu značaj razvoja naprednih nanomaterijala za zaštitu prirodne okoline, u ovome radu su prezentovane primene nanomaterijala i nanostruktura na bazi TiO2 u oblastima obnovljivih izvora energije, hemijske i bio dekontaminacije. Objašnjena je uloga TiO2 u formiranju kompozitnih hibridnih struktura za prikupljanje solarne energije, kao i primena različitih antimikrobnih materijala na bazi TiO2 koji se koriste za fotokatalitičko uklanjanje polutanata. Naročita pažnja je posvećena strukturi i svojstvima titan dioksidnih nanotuba dobijenih primenom metode elektrohemijske anodizacije i njihova primena u bio dekontaminaciji.",
publisher = "Inženjersko društvo za koroziju, Beograd",
journal = "Zaštita materijala",
title = "TiO2 based nanomaterials and nanostructures for green convergent technologies and environmental protection, Nanomaterijali i nanostrukture na bazi TiO2 za zelene konvergentne tehnologije i zaštitu prirodne okoline",
pages = "355-346",
number = "4",
volume = "61",
doi = "10.5937/zasmat2004346P"
}

Pavlović, V. B., Vujančević, J., Vlahović, B.,& Pavlović, V. P.. (2020). TiO2 based nanomaterials and nanostructures for green convergent technologies and environmental protection. in Zaštita materijala
Inženjersko društvo za koroziju, Beograd., 61(4), 346-355.
https://doi.org/10.5937/zasmat2004346P

Pavlović VB, Vujančević J, Vlahović B, Pavlović VP. TiO2 based nanomaterials and nanostructures for green convergent technologies and environmental protection. in Zaštita materijala. 2020;61(4):346-355.
doi:10.5937/zasmat2004346P .

Pavlović, Vladimir B., Vujančević, Jelena, Vlahović, Branislav, Pavlović, Vera P., "TiO2 based nanomaterials and nanostructures for green convergent technologies and environmental protection" in Zaštita materijala, 61, no. 4 (2020):346-355,
https://doi.org/10.5937/zasmat2004346P . .

TY  - JOUR
AU  - Drazić, Milan
AU  - Gligorević, Kosta
AU  - Pajić, Miloš B.
AU  - Zlatanović, Ivan
AU  - Spalević, Velibor
AU  - Sestras, Paul
AU  - Skatarić, Goran
AU  - Dudić, Branislav
PY  - 2020
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/3416
AB  - The aim of this research was to study the impact of application technique and rate of liquid starter fertilizer applied with a novel device on the production of corn. Starter fertilizer was applied in the root system range of freshly germinated plants in the 'belt' and 'point' forms at different quantities (35, 50, 70, and 100 L ha(-1)), which led to intensive plant growth in the initial stages of development. This adapted system was used for sowing and for application of the liquid starter fertilizer at the same time. The field trial was set up at two sites (two different land types), in the conditions of the natural water regime of the soil during the three vegetation seasons in the period 2016-2018. For this purpose, a prototype of the electronic device EUKU-01 was designed. The starter fertilizer was applied at 5 cm laterally from the row where the sowing was performed and 5 cm below the depth at which the corn seeds were sown. Data were statistically analyzed by two-factor analysis of variance, where the influence of mineral fertilizer treatment and the influence of liquid starter fertilizer treatment were observed as factors. The results showed that the optimal choice of the technique of liquid starter fertilizer application can result in fertilizer savings by 30% without reducing yield.
PB  - MDPI, Basel
T2  - Agriculture
T1  - The Influence of the Application Technique and Amount of Liquid Starter Fertilizer on Corn Yield
IS  - 8
VL  - 10
DO  - 10.3390/agriculture10080347
ER  - 

@article{
author = "Drazić, Milan and Gligorević, Kosta and Pajić, Miloš B. and Zlatanović, Ivan and Spalević, Velibor and Sestras, Paul and Skatarić, Goran and Dudić, Branislav",
year = "2020",
abstract = "The aim of this research was to study the impact of application technique and rate of liquid starter fertilizer applied with a novel device on the production of corn. Starter fertilizer was applied in the root system range of freshly germinated plants in the 'belt' and 'point' forms at different quantities (35, 50, 70, and 100 L ha(-1)), which led to intensive plant growth in the initial stages of development. This adapted system was used for sowing and for application of the liquid starter fertilizer at the same time. The field trial was set up at two sites (two different land types), in the conditions of the natural water regime of the soil during the three vegetation seasons in the period 2016-2018. For this purpose, a prototype of the electronic device EUKU-01 was designed. The starter fertilizer was applied at 5 cm laterally from the row where the sowing was performed and 5 cm below the depth at which the corn seeds were sown. Data were statistically analyzed by two-factor analysis of variance, where the influence of mineral fertilizer treatment and the influence of liquid starter fertilizer treatment were observed as factors. The results showed that the optimal choice of the technique of liquid starter fertilizer application can result in fertilizer savings by 30% without reducing yield.",
publisher = "MDPI, Basel",
journal = "Agriculture",
title = "The Influence of the Application Technique and Amount of Liquid Starter Fertilizer on Corn Yield",
number = "8",
volume = "10",
doi = "10.3390/agriculture10080347"
}

Drazić, M., Gligorević, K., Pajić, M. B., Zlatanović, I., Spalević, V., Sestras, P., Skatarić, G.,& Dudić, B.. (2020). The Influence of the Application Technique and Amount of Liquid Starter Fertilizer on Corn Yield. in Agriculture
MDPI, Basel., 10(8).
https://doi.org/10.3390/agriculture10080347

Drazić M, Gligorević K, Pajić MB, Zlatanović I, Spalević V, Sestras P, Skatarić G, Dudić B. The Influence of the Application Technique and Amount of Liquid Starter Fertilizer on Corn Yield. in Agriculture. 2020;10(8).
doi:10.3390/agriculture10080347 .

Drazić, Milan, Gligorević, Kosta, Pajić, Miloš B., Zlatanović, Ivan, Spalević, Velibor, Sestras, Paul, Skatarić, Goran, Dudić, Branislav, "The Influence of the Application Technique and Amount of Liquid Starter Fertilizer on Corn Yield" in Agriculture, 10, no. 8 (2020),
https://doi.org/10.3390/agriculture10080347 . .