TY  - CONF
AU  - Misita, Mirjana
AU  - Spasojević Brkić, Vesna
AU  - Perišić, Martina
AU  - Milanović, Marija
AU  - Borota-Tišma, Ankica
PY  - 2020
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/4119
AB  - This paper presents an approach to the digitalization of the workplace risk assessment and monitoring process. Workplace risk was assessed using the “5x5” method. Workplace are spatially distributed in the observed factory. The summary risk assessment is presented visually and the high-risk workplace is marked. The map is made dynamically so that the job estimates on the diagram changes if there is a charge in the input data for any of the identified sources of risk.
PB  - Technical faculty “Mihajlo Pupin”, Zrenjanin, University of Novi Sad
C3  - X International Conference Industrial Engineering and
Environmental Protection (IIZS 2020) : Proceedings, Zrenjanin, 8-9th October 2020.
T1  - An approach forward to digitalization of workplace risk assessment and monitoring
UR  - https://hdl.handle.net/21.15107/rcub_machinery_4119
ER  - 

@conference{
author = "Misita, Mirjana and Spasojević Brkić, Vesna and Perišić, Martina and Milanović, Marija and Borota-Tišma, Ankica",
year = "2020",
abstract = "This paper presents an approach to the digitalization of the workplace risk assessment and monitoring process. Workplace risk was assessed using the “5x5” method. Workplace are spatially distributed in the observed factory. The summary risk assessment is presented visually and the high-risk workplace is marked. The map is made dynamically so that the job estimates on the diagram changes if there is a charge in the input data for any of the identified sources of risk.",
publisher = "Technical faculty “Mihajlo Pupin”, Zrenjanin, University of Novi Sad",
journal = "X International Conference Industrial Engineering and
Environmental Protection (IIZS 2020) : Proceedings, Zrenjanin, 8-9th October 2020.",
title = "An approach forward to digitalization of workplace risk assessment and monitoring",
url = "https://hdl.handle.net/21.15107/rcub_machinery_4119"
}

Misita, M., Spasojević Brkić, V., Perišić, M., Milanović, M.,& Borota-Tišma, A.. (2020). An approach forward to digitalization of workplace risk assessment and monitoring. in X International Conference Industrial Engineering and
Environmental Protection (IIZS 2020) : Proceedings, Zrenjanin, 8-9th October 2020.
Technical faculty “Mihajlo Pupin”, Zrenjanin, University of Novi Sad..
https://hdl.handle.net/21.15107/rcub_machinery_4119

Misita M, Spasojević Brkić V, Perišić M, Milanović M, Borota-Tišma A. An approach forward to digitalization of workplace risk assessment and monitoring. in X International Conference Industrial Engineering and
Environmental Protection (IIZS 2020) : Proceedings, Zrenjanin, 8-9th October 2020.. 2020;.
https://hdl.handle.net/21.15107/rcub_machinery_4119 .

Misita, Mirjana, Spasojević Brkić, Vesna, Perišić, Martina, Milanović, Marija, Borota-Tišma, Ankica, "An approach forward to digitalization of workplace risk assessment and monitoring" in X International Conference Industrial Engineering and
Environmental Protection (IIZS 2020) : Proceedings, Zrenjanin, 8-9th October 2020. (2020),
https://hdl.handle.net/21.15107/rcub_machinery_4119 .

TY  - JOUR
AU  - Milanović, Marija
AU  - Misita, Mirjana
AU  - Komatina, Nikola
PY  - 2020
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/3290
AB  - In this paper, we consider the problem of determining the optimal production quantity under uncertainties. The treated problem has a critical effect on the achievement of business goals, which further propagates to the competitive advantage of manufacturing company. The considered problem is stated as the fuzzy linear programming task. The objective function is defined as the maximization of all profit over the time period. The set of constraints consists of constraints deriving from the enterprise (available capacities) and from the market (demand). The fuzzy rating coefficient values of objective function of each pair of the considered products are described by linguistic expressions which are modelled by triangular fuzzy numbers. Handling of uncertainties of the stated fuzzy pair-wise comparison matrix is performed by using the extent analysis. The right-hand-side values of the capacity constraints are determined by decision makers and modelled by the triangular fuzzy numbers. The market constraint values are given according to evidence data. Determination of the optimal quantities of considered products for each time period is based on the concept of equal possibilities. The proposed model is illustrated by an example with real-life data.
PB  - IOS Press, Amsterdam
T2  - Journal of Intelligent & Fuzzy Systems
T1  - Determination of the optimal production plan by using fuzzy AHP and fuzzy linear programming
EP  - 4325
IS  - 4
SP  - 4315
VL  - 38
DO  - 10.3233/JIFS-190913
ER  - 

@article{
author = "Milanović, Marija and Misita, Mirjana and Komatina, Nikola",
year = "2020",
abstract = "In this paper, we consider the problem of determining the optimal production quantity under uncertainties. The treated problem has a critical effect on the achievement of business goals, which further propagates to the competitive advantage of manufacturing company. The considered problem is stated as the fuzzy linear programming task. The objective function is defined as the maximization of all profit over the time period. The set of constraints consists of constraints deriving from the enterprise (available capacities) and from the market (demand). The fuzzy rating coefficient values of objective function of each pair of the considered products are described by linguistic expressions which are modelled by triangular fuzzy numbers. Handling of uncertainties of the stated fuzzy pair-wise comparison matrix is performed by using the extent analysis. The right-hand-side values of the capacity constraints are determined by decision makers and modelled by the triangular fuzzy numbers. The market constraint values are given according to evidence data. Determination of the optimal quantities of considered products for each time period is based on the concept of equal possibilities. The proposed model is illustrated by an example with real-life data.",
publisher = "IOS Press, Amsterdam",
journal = "Journal of Intelligent & Fuzzy Systems",
title = "Determination of the optimal production plan by using fuzzy AHP and fuzzy linear programming",
pages = "4325-4315",
number = "4",
volume = "38",
doi = "10.3233/JIFS-190913"
}

Milanović, M., Misita, M.,& Komatina, N.. (2020). Determination of the optimal production plan by using fuzzy AHP and fuzzy linear programming. in Journal of Intelligent & Fuzzy Systems
IOS Press, Amsterdam., 38(4), 4315-4325.
https://doi.org/10.3233/JIFS-190913

Milanović M, Misita M, Komatina N. Determination of the optimal production plan by using fuzzy AHP and fuzzy linear programming. in Journal of Intelligent & Fuzzy Systems. 2020;38(4):4315-4325.
doi:10.3233/JIFS-190913 .

Milanović, Marija, Misita, Mirjana, Komatina, Nikola, "Determination of the optimal production plan by using fuzzy AHP and fuzzy linear programming" in Journal of Intelligent & Fuzzy Systems, 38, no. 4 (2020):4315-4325,
https://doi.org/10.3233/JIFS-190913 . .

TY  - CONF
AU  - Milanović, Dragan
AU  - Misita, Mirjana
AU  - Kefer, Petar
AU  - Borota-Tišma, Ankica
AU  - Milanović, Marija
PY  - 2019
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/4129
AB  - U radu se istražuje strategijski pristup upravljanja lancima snabdevanja sa stanovišta Lean distribucije. Upravljanje lancima snabdevanja je proces dizajniranja, planiranja, izvršenja, kontrole i nadgledanja aktivnosti lanaca snabdevanja sa svrhom da se kreira neto vrednost, koja izgrađuje konkurentnu infrastrukturu, balansira internacionalnu logistiku, sinhronizuje snabdevanje sa potrebama i meri performansu poslovanja na globalnom nivou. Najbolje kompanije na svetu nalaze novi izvor konkurentne prednosti u upravljanju lancima snabdevanja, koji sadrži veliki broj aktivnosti koje su integrisane, kako bi proizvod ili usluga za što kraće vreme došli na tržište i zadovoljili potrebe kupca. Istraživanje definiše pet osnovnih postavki implementacije strategije upravljanja lancima snabdevanja sa stanovišta Lean distribucije.
PB  - Pirot : UO Privredna komora
C3  - III Međunarodna naučno-stručna konferencija Regionalni razvoj i saradnja : zbornik radova
T1  - Strategijski pristup upravljanja lancima snabdevanja sa stanovišta Lean distribucije
UR  - https://hdl.handle.net/21.15107/rcub_machinery_4129
ER  - 

@conference{
author = "Milanović, Dragan and Misita, Mirjana and Kefer, Petar and Borota-Tišma, Ankica and Milanović, Marija",
year = "2019",
abstract = "U radu se istražuje strategijski pristup upravljanja lancima snabdevanja sa stanovišta Lean distribucije. Upravljanje lancima snabdevanja je proces dizajniranja, planiranja, izvršenja, kontrole i nadgledanja aktivnosti lanaca snabdevanja sa svrhom da se kreira neto vrednost, koja izgrađuje konkurentnu infrastrukturu, balansira internacionalnu logistiku, sinhronizuje snabdevanje sa potrebama i meri performansu poslovanja na globalnom nivou. Najbolje kompanije na svetu nalaze novi izvor konkurentne prednosti u upravljanju lancima snabdevanja, koji sadrži veliki broj aktivnosti koje su integrisane, kako bi proizvod ili usluga za što kraće vreme došli na tržište i zadovoljili potrebe kupca. Istraživanje definiše pet osnovnih postavki implementacije strategije upravljanja lancima snabdevanja sa stanovišta Lean distribucije.",
publisher = "Pirot : UO Privredna komora",
journal = "III Međunarodna naučno-stručna konferencija Regionalni razvoj i saradnja : zbornik radova",
title = "Strategijski pristup upravljanja lancima snabdevanja sa stanovišta Lean distribucije",
url = "https://hdl.handle.net/21.15107/rcub_machinery_4129"
}

Milanović, D., Misita, M., Kefer, P., Borota-Tišma, A.,& Milanović, M.. (2019). Strategijski pristup upravljanja lancima snabdevanja sa stanovišta Lean distribucije. in III Međunarodna naučno-stručna konferencija Regionalni razvoj i saradnja : zbornik radova
Pirot : UO Privredna komora..
https://hdl.handle.net/21.15107/rcub_machinery_4129

Milanović D, Misita M, Kefer P, Borota-Tišma A, Milanović M. Strategijski pristup upravljanja lancima snabdevanja sa stanovišta Lean distribucije. in III Međunarodna naučno-stručna konferencija Regionalni razvoj i saradnja : zbornik radova. 2019;.
https://hdl.handle.net/21.15107/rcub_machinery_4129 .

Milanović, Dragan, Misita, Mirjana, Kefer, Petar, Borota-Tišma, Ankica, Milanović, Marija, "Strategijski pristup upravljanja lancima snabdevanja sa stanovišta Lean distribucije" in III Međunarodna naučno-stručna konferencija Regionalni razvoj i saradnja : zbornik radova (2019),
https://hdl.handle.net/21.15107/rcub_machinery_4129 .

TY  - CONF
AU  - Misita, Mirjana
AU  - Milanović, Marija
AU  - Tabašević, Ilija
PY  - 2018
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/4117
AB  - The paper shows research of production
program optimization in business-production
systems. In paper is shown generating optimal
criteria and constrains, and finding optimal solution
for each product volume. Nonlinear functions in
model are used. Extremes of objective functions are
used for calculating deviations from optimal volume
and size of admissible area for each product.
PB  - Belgrade : Faculty of Mechanical Engineering
C3  - 7th International Symposium of Industrial Engineering -
SIE 2018 : Proceedings, 27th-28th September, 2018, Belgrade
T1  - Example of production processes optimization
UR  - https://hdl.handle.net/21.15107/rcub_machinery_4117
ER  - 

@conference{
author = "Misita, Mirjana and Milanović, Marija and Tabašević, Ilija",
year = "2018",
abstract = "The paper shows research of production
program optimization in business-production
systems. In paper is shown generating optimal
criteria and constrains, and finding optimal solution
for each product volume. Nonlinear functions in
model are used. Extremes of objective functions are
used for calculating deviations from optimal volume
and size of admissible area for each product.",
publisher = "Belgrade : Faculty of Mechanical Engineering",
journal = "7th International Symposium of Industrial Engineering -
SIE 2018 : Proceedings, 27th-28th September, 2018, Belgrade",
title = "Example of production processes optimization",
url = "https://hdl.handle.net/21.15107/rcub_machinery_4117"
}

Misita, M., Milanović, M.,& Tabašević, I.. (2018). Example of production processes optimization. in 7th International Symposium of Industrial Engineering -
SIE 2018 : Proceedings, 27th-28th September, 2018, Belgrade
Belgrade : Faculty of Mechanical Engineering..
https://hdl.handle.net/21.15107/rcub_machinery_4117

Misita M, Milanović M, Tabašević I. Example of production processes optimization. in 7th International Symposium of Industrial Engineering -
SIE 2018 : Proceedings, 27th-28th September, 2018, Belgrade. 2018;.
https://hdl.handle.net/21.15107/rcub_machinery_4117 .

Misita, Mirjana, Milanović, Marija, Tabašević, Ilija, "Example of production processes optimization" in 7th International Symposium of Industrial Engineering -
SIE 2018 : Proceedings, 27th-28th September, 2018, Belgrade (2018),
https://hdl.handle.net/21.15107/rcub_machinery_4117 .

TY  - JOUR
AU  - Syzrantsev, Vladimir
AU  - Syzrantseva, Ksenia
AU  - Pazyak, Andrey
AU  - Milanović, Marija
PY  - 2017
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/2616
AB  - Korišćenjem konusnih zupčanika sa malim uglom precesije gornjeg konusa razvijen je pogon za jedan deo opreme na gas i ulje. Zupčanici se odlikuju visokim stepenom iskorišćenosti (oko 0,9) i malim početnim obrtnim momentom. Zahvaljujući sprezanju većeg broja parova zubaca ovi zupčanici imaju veći kapacitet opterećenja u poređenju sa drugim tipovima zupčanika, što obezbeđuje bezbedan rad na dalekom severu. Danas se najviše proučavaju konusni zupčanici sa malim uglom gornjeg konusa sa dvostrukim konkavno-konveksnim zupcima. Međutim, proces izrade zubaca takvih zupčanika je izuzetno komplikovan - mašina mora da se resetuje četiri puta. Tehnologija izrade se može pojednostaviti korišćenjem zupčanika bez ozubljenog većeg i sa ozubljenim manjim zupčanikom. Članak prikazuje izračunavanja pravaca dejstva kod sprezanja i redukovanu osnovnu zakrivljenost pravozubih konusnih zupčanika sa malim uglom gornjeg konusa bez ozubljenog većeg i sa ozubljenim manjim zupčanikom, geometrijske karakteristike potrebne za određivanje napona u kontaktu koji nastaje sprezanjem zubaca i za razvoj metoda za izračunavanje kapaciteta opterećenja zupčanika.
AB  - Based on the precessional bevel gears with a small shaft angle, a number of drives for oil and gas equipment have been developed. They are characterized by high efficiency (about 0.9) and a small starting torque. Due to multi-pair tooth meshing they have a higher load capacity as compared to other types of gears, which provides a safe drive operation in the Far North. Currently, the most studied gears are bevel gears with a small shaft angle with double-concave-convex teeth. However, the process of gear cutting for such gears is extremely complicated - the machine has to be reset four times. The cutting technology can be simplified by using gears with a non-generated gear and a generated pinion. The article provides calculations of the lines of action in meshing and the principal reduced curvature for a straight bevel gears with a small shaft angle with a non-generated gear and a generated pinion, geometrical characteristics necessary for determining the contact stress arising in tooth meshing and for developing methods of calculating the gear load capacity.
PB  - Univerzitet u Beogradu - Mašinski fakultet, Beograd
T2  - FME Transactions
T1  - Istraživanje geometrijskih karakteristika pravozubih konusnih zupčanika sa malim uglom gornjeg konusa bez ozubljenog većeg a sa ozubljenim manjim zupčanikom
T1  - Research on geometrical characteristics of straight bevel gears with a small shaft angle with a non-generated gear and generated pinion
EP  - 669
IS  - 4
SP  - 661
VL  - 45
DO  - 10.5937/fmet1704661S
ER  - 

@article{
author = "Syzrantsev, Vladimir and Syzrantseva, Ksenia and Pazyak, Andrey and Milanović, Marija",
year = "2017",
abstract = "Korišćenjem konusnih zupčanika sa malim uglom precesije gornjeg konusa razvijen je pogon za jedan deo opreme na gas i ulje. Zupčanici se odlikuju visokim stepenom iskorišćenosti (oko 0,9) i malim početnim obrtnim momentom. Zahvaljujući sprezanju većeg broja parova zubaca ovi zupčanici imaju veći kapacitet opterećenja u poređenju sa drugim tipovima zupčanika, što obezbeđuje bezbedan rad na dalekom severu. Danas se najviše proučavaju konusni zupčanici sa malim uglom gornjeg konusa sa dvostrukim konkavno-konveksnim zupcima. Međutim, proces izrade zubaca takvih zupčanika je izuzetno komplikovan - mašina mora da se resetuje četiri puta. Tehnologija izrade se može pojednostaviti korišćenjem zupčanika bez ozubljenog većeg i sa ozubljenim manjim zupčanikom. Članak prikazuje izračunavanja pravaca dejstva kod sprezanja i redukovanu osnovnu zakrivljenost pravozubih konusnih zupčanika sa malim uglom gornjeg konusa bez ozubljenog većeg i sa ozubljenim manjim zupčanikom, geometrijske karakteristike potrebne za određivanje napona u kontaktu koji nastaje sprezanjem zubaca i za razvoj metoda za izračunavanje kapaciteta opterećenja zupčanika., Based on the precessional bevel gears with a small shaft angle, a number of drives for oil and gas equipment have been developed. They are characterized by high efficiency (about 0.9) and a small starting torque. Due to multi-pair tooth meshing they have a higher load capacity as compared to other types of gears, which provides a safe drive operation in the Far North. Currently, the most studied gears are bevel gears with a small shaft angle with double-concave-convex teeth. However, the process of gear cutting for such gears is extremely complicated - the machine has to be reset four times. The cutting technology can be simplified by using gears with a non-generated gear and a generated pinion. The article provides calculations of the lines of action in meshing and the principal reduced curvature for a straight bevel gears with a small shaft angle with a non-generated gear and a generated pinion, geometrical characteristics necessary for determining the contact stress arising in tooth meshing and for developing methods of calculating the gear load capacity.",
publisher = "Univerzitet u Beogradu - Mašinski fakultet, Beograd",
journal = "FME Transactions",
title = "Istraživanje geometrijskih karakteristika pravozubih konusnih zupčanika sa malim uglom gornjeg konusa bez ozubljenog većeg a sa ozubljenim manjim zupčanikom, Research on geometrical characteristics of straight bevel gears with a small shaft angle with a non-generated gear and generated pinion",
pages = "669-661",
number = "4",
volume = "45",
doi = "10.5937/fmet1704661S"
}

Syzrantsev, V., Syzrantseva, K., Pazyak, A.,& Milanović, M.. (2017). Istraživanje geometrijskih karakteristika pravozubih konusnih zupčanika sa malim uglom gornjeg konusa bez ozubljenog većeg a sa ozubljenim manjim zupčanikom. in FME Transactions
Univerzitet u Beogradu - Mašinski fakultet, Beograd., 45(4), 661-669.
https://doi.org/10.5937/fmet1704661S

Syzrantsev V, Syzrantseva K, Pazyak A, Milanović M. Istraživanje geometrijskih karakteristika pravozubih konusnih zupčanika sa malim uglom gornjeg konusa bez ozubljenog većeg a sa ozubljenim manjim zupčanikom. in FME Transactions. 2017;45(4):661-669.
doi:10.5937/fmet1704661S .

Syzrantsev, Vladimir, Syzrantseva, Ksenia, Pazyak, Andrey, Milanović, Marija, "Istraživanje geometrijskih karakteristika pravozubih konusnih zupčanika sa malim uglom gornjeg konusa bez ozubljenog većeg a sa ozubljenim manjim zupčanikom" in FME Transactions, 45, no. 4 (2017):661-669,
https://doi.org/10.5937/fmet1704661S . .

TY  - CONF
AU  - Syzrantsev, Vladimir
AU  - Syzrantseva, Ksenia
AU  - Milanović, Marija
AU  - Pazyak, A.
PY  - 2016
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/2425
AB  - The aim of this paper is to analyse the semi-rolling bevel precessional gear with straight teeth. The given method of cutting pinion and gear teeth significantly simplifies its manufacture technology. Authors have given a system of equations to study the analysis of generating pinion tooth surfaces and geometry of meshing for semi-rolling bevel precessional gear with straight teeth. A computer program was developed to enable implement formulas provided in the paper. By using this program authors obtained contact lines on the pinion tooth surface and number of tooth pairs in gears mesh.
PB  - IOP Publishing Ltd, Bristol
C3  - Vii International Scientific Practical Conference Innovative Technologies in Engineering
T1  - Determination of Geometrical Parameters for Semi-Rolling Bevel Precessional Gears With Straight Teeth
VL  - 142
DO  - 10.1088/1757-899X/142/1/012086
ER  - 

@conference{
author = "Syzrantsev, Vladimir and Syzrantseva, Ksenia and Milanović, Marija and Pazyak, A.",
year = "2016",
abstract = "The aim of this paper is to analyse the semi-rolling bevel precessional gear with straight teeth. The given method of cutting pinion and gear teeth significantly simplifies its manufacture technology. Authors have given a system of equations to study the analysis of generating pinion tooth surfaces and geometry of meshing for semi-rolling bevel precessional gear with straight teeth. A computer program was developed to enable implement formulas provided in the paper. By using this program authors obtained contact lines on the pinion tooth surface and number of tooth pairs in gears mesh.",
publisher = "IOP Publishing Ltd, Bristol",
journal = "Vii International Scientific Practical Conference Innovative Technologies in Engineering",
title = "Determination of Geometrical Parameters for Semi-Rolling Bevel Precessional Gears With Straight Teeth",
volume = "142",
doi = "10.1088/1757-899X/142/1/012086"
}

Syzrantsev, V., Syzrantseva, K., Milanović, M.,& Pazyak, A.. (2016). Determination of Geometrical Parameters for Semi-Rolling Bevel Precessional Gears With Straight Teeth. in Vii International Scientific Practical Conference Innovative Technologies in Engineering
IOP Publishing Ltd, Bristol., 142.
https://doi.org/10.1088/1757-899X/142/1/012086

Syzrantsev V, Syzrantseva K, Milanović M, Pazyak A. Determination of Geometrical Parameters for Semi-Rolling Bevel Precessional Gears With Straight Teeth. in Vii International Scientific Practical Conference Innovative Technologies in Engineering. 2016;142.
doi:10.1088/1757-899X/142/1/012086 .

Syzrantsev, Vladimir, Syzrantseva, Ksenia, Milanović, Marija, Pazyak, A., "Determination of Geometrical Parameters for Semi-Rolling Bevel Precessional Gears With Straight Teeth" in Vii International Scientific Practical Conference Innovative Technologies in Engineering, 142 (2016),
https://doi.org/10.1088/1757-899X/142/1/012086 . .

TY  - JOUR
AU  - Lapcević, Nebojša
AU  - Misita, Mirjana
AU  - Milanović, Marija
AU  - Spasojević Brkić, Vesna
AU  - Tadić, Danijela
PY  - 2013
UR  - https://machinery.mas.bg.ac.rs/handle/123456789/1817
AB  - This paper presents the research of implementing the ERP (Enterprise Resource Planning) in manufacturing companies. Identified the factors that influence the assessment of the success of ERP implementation in manufacturing companies. It was found that the training of employees, especially management has great significance in the degree of success of ERP implementation and business results as well as after implementation of ERP. A high degree of correlation between the observed parameters confirmed the testing of the hypothesis set.
PB  - Editura Stiintifica F. M. R.
T2  - Metalurgia International
T1  - Research into factors that influence the success of erp implementation in a Serbian production company
EP  - 174
IS  - 2
SP  - 172
VL  - 18
UR  - https://hdl.handle.net/21.15107/rcub_machinery_1817
ER  - 

@article{
author = "Lapcević, Nebojša and Misita, Mirjana and Milanović, Marija and Spasojević Brkić, Vesna and Tadić, Danijela",
year = "2013",
abstract = "This paper presents the research of implementing the ERP (Enterprise Resource Planning) in manufacturing companies. Identified the factors that influence the assessment of the success of ERP implementation in manufacturing companies. It was found that the training of employees, especially management has great significance in the degree of success of ERP implementation and business results as well as after implementation of ERP. A high degree of correlation between the observed parameters confirmed the testing of the hypothesis set.",
publisher = "Editura Stiintifica F. M. R.",
journal = "Metalurgia International",
title = "Research into factors that influence the success of erp implementation in a Serbian production company",
pages = "174-172",
number = "2",
volume = "18",
url = "https://hdl.handle.net/21.15107/rcub_machinery_1817"
}

Lapcević, N., Misita, M., Milanović, M., Spasojević Brkić, V.,& Tadić, D.. (2013). Research into factors that influence the success of erp implementation in a Serbian production company. in Metalurgia International
Editura Stiintifica F. M. R.., 18(2), 172-174.
https://hdl.handle.net/21.15107/rcub_machinery_1817

Lapcević N, Misita M, Milanović M, Spasojević Brkić V, Tadić D. Research into factors that influence the success of erp implementation in a Serbian production company. in Metalurgia International. 2013;18(2):172-174.
https://hdl.handle.net/21.15107/rcub_machinery_1817 .

Lapcević, Nebojša, Misita, Mirjana, Milanović, Marija, Spasojević Brkić, Vesna, Tadić, Danijela, "Research into factors that influence the success of erp implementation in a Serbian production company" in Metalurgia International, 18, no. 2 (2013):172-174,
https://hdl.handle.net/21.15107/rcub_machinery_1817 .